Amart Furniture SIGNATURE 64105 User manual

ASSEMBLY INSTRUCTION
LA SALLE BENCH SEAT
ITEM CODE 64105
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
64105

IMPORTANT: CARE GUIDE FOR YOUR
TIMBER FURNITURE
•Congratulations! You have just purchased a quality product from
Amart Furniture. Please read on for important information regarding
your purchase.
•A multi-step finish is applied to all our furniture, but all wood comes
from nature. Because of this, there will be natural variations in
surface texture and grain like knots, mineral streaks and sap runs that
may affect the finish.
•These differences in character are not defects, but distinctions that
make each piece of furniture unique.
•Our furniture is built to last. Following these steps for basic care
should protect your investment for years to come.
•Dust frequently with a clean damp lint-free cloth. This will help
remove abrasive build up which can damage a finish over time.
•Do not place hot objects on any furniture surface. Always use a
coaster or placemat. Laminate and lacquer finishes on table tops
provide added scratch and heat resistance to our furniture, but they
can still be damaged without proper care.
•Avoid exposing your furniture to strong sunlight, heat outlets, open
windows or dampness. Prolonged exposure to direct sunlight can fade
the finish of your furniture, while extreme temperature and humidity
changes can cause cracking or splitting.
•Do not expose your furniture to any liquids. Never allow water to sit
on your furniture. Alcohol, nail polish and perfume are also dangerous
as they will dissolve the lacquer finish on contact and may require
professional repairs.
•Do not allow plastic to come in direct contact with your furniture.
Chemicals in the plastic of placemats etc may soften and mark the
finish if left in contact with the furniture for a period of time.
164105

PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to
the point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
2
Allow at least 45min you will need 2 people
264105

Part
DESCRIPTION
Qty
In box
Part
DESCRIPTION
Qty
In box
1
BENCH TOP
1
1
4
CROSS BAR
1
1
2
RAILS
2
1
5
LEGS
2
2
3
PEDESTALS
2
2
6
SUPPORT BAR
1
1
PARTS LIST
3
A
M6 X 30 BOLT
16
PCES
B
M6 X 80 BOLT
8
PCES
C
M8 X 50 BOLT
2
PCE
S
D
M6 X 60 BOLT
3PC
ES
E
CURVED
WASHER
2PCE
S
F
M6.5 X 19 FLAT
WASHER
24
PCES
G
M6.5 X 9
SPRING
WASHER
24
PCE
S
H
ALLEN KEY
1
PCE
64105

Step 1
You should have started by opening box 1, upside down. Keep
the bench top inside the box until later advised. Open the
legs box as the hardware is in there.
Step 2
Next you will need to assemble the M6 x 30 bolts (item A) with
the M6.5 x 9 spring washers (item G) and the M6.5 x 19 flat
washers (item F)
A
M6 X 30 BOLT
8
PCES
F
M6.5 X 19 FLAT
WASHER
8
PCES
G
M6.5 X 9
SPRING
WASHER
8
PCES
H
ALLEN KEY
1 PCE
YOU WILL NEED
464105

Step 3
With the assembled bolts from step 2, attach a rail (part 2) to
a pedestal (part 3) as per diagram below. Make sure the
pedestal is standing upright at all times as shown, we
recommend 2 people for this, with one holding the pedestal at
all times. Fasten firmly, but do not over tighten, over
tightening may damage surface of item.
Step 4
Repeat Step 3, with the remaining rail and pedestal. You
should be left with 8 sets of the assembled bolts from step 2,
you will need them for step 8
564105

Step 5
Next you will need to assemble the M6 x 80 bolts (item B) with
the M6.5 x 9 spring washers (item G) and the M6.5 x 19 flat
washers (item F)
Step 6
With the assembled bolts from step 5, attach a leg (part 5) to
a pedestal (part 3) as per diagram below. Make sure the
pedestal is standing upright at all times as shown, we
recommend 2 people for this, with one holding the pedestal at
all times. Fasten firmly, but do not over tighten, over
tightening may damage surface of item.
B
M6 X 80 BOLT
16
PCES
F
M6.5 X 19 FLAT
WASHER
16
PCES
G
M6.5 X 9
SPRING
WASHER
16
PCES
H
ALLEN KEY
1 PCE
YOU WILL NEED
664105

Step 7
Repeat Step 6 with the other leg and pedestal.
Step 8
Next we’ll be attaching the leg structures to the bench top.
We recommend 2 people for this with one person holding the
leg structure up right at all times. take the 8 remaining
assembled bolt sets from step 2. Affix the leg structure to the
table top with these using the Allen key provided (item H), as
per the diagram below. Fasten firmly, but do not over tighten,
over tightening may damage surface of item. Repeat for the
other side.
764105

D
M6 X 60 BOLT
3
PCES
H
ALLEN KEY
1 PCE
Step 9
Next we’ll be attaching the support bar (part 6) onto the
bench top. You will need 3, M6 x 60 bolts (item D) fastened
with the Allen key supplied (item H), as per the diagram
below. Fasten firmly, but do not over tighten, over tightening
may damage surface of item.
8
YOU WILL NEED
64105

Step 10
Next we’ll be attaching the cross bar. You will require 2
people for this step. One to fasten one end whilst the other
holds the other end in place. Due to the space constraint of
the slotted hole, please be patient whilst fastening the bolt.
Start by placing the curved washer (item D), into place as
shown below, then insert the bolt (item C) and fasten. Fasten
firmly, but do not over tighten, over tightening may damage
surface of item. Repeat for the other side.
9
C
M6 X 50 BOLT
2
PCES
E
CURVED
WASHER
2
PCES
H
ALLEN KEY
1 PCE
YOU WILL NEED
64105