Amart Furniture KHYBER 72840 User manual

ASSEMBLY INSTRUCTION
KHYBER QUEEN BED
ITEM CODE 72840
Imported by Amart Furniture Pty Ltd,Brisbane, Qld, Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
870mm
2160mm
1630mm
Imported by Amart Furniture Pty Ltd, Brisbane, Qld, Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
1 Item code 72840

Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
PRE-ASSEMBLY PREPARATION
2Item code 72840

Hardware List
Parts List
A B CD
E F GH
IJ K L
M N OP
1 2 3 4
5678
9
Headboard 1PC Foot Board 1PC SideRail 2PCS PlatformBottomRail
1PC
Single Plastic Cap 30pcs Double Plastic Cap 15pcsSlat 30 PCS
2PCS
4PCSLeg 4PCS
CentreSupportBar1PC Handle 1PC 
16 pcs
M8*30 x20 PCS
M5 x1PC
M8*50 x4PCS
PlatformSideRail2PC
M8*40 x14 PCS
SupportLeg 2PCS
1PCS
8pcs
12 pcs 1pcs1pcs
10 M8*40 x2PCS
Middle bar1PC
Q
PlatformTopRail1PC
3 Item code 72840
11 M6*20 x8SETS M4 x2PCS
12

1
4
5
6
C
C
L
1
6
Step1
5 8pcs
4 8pcs
1 16pcs
6 1pc
L 2pcs
Step2
B
A
Attach Legs (I) to bottom of Headboard (A) and Footboard (B) using Bolt (9) and Washer (5) as shown below.
Tighten with Allen key (6).
Connect Bolts (1) with Washer (5) and Spring washer (4) to Headboard (A) and Footboard (B).Do not tighten
these bolts fully until after Middle bar has been attached in Step 5. Attach Side Rails (C) to Headboard (A) and
Footboard (B) by hooking brackets over these bolts.
Attach Support Bracket (L) to Side Rail (C) and Footboard (B) using
Bolt (1) and Tighten with Allen Key (6).
5
9
6
I
I
I
I
I
4Item code 72840

J 4 pcs
2 8 pcs
3 8 pcs
7 1 pc
Step3
Step4
8 1
pc
8 1 pc
8
Attach the platform top rail(M), platform bottom rail(D) and platform side rail(E) using corner connectors (J),
fasten them with bolts and barrel nuts (11) and tighten with allen key (12). Then attach the centre support bar(O)
with the bolts(2) and nuts(3), tighten them by spanner(7) and screw driver(8). Attach support legs(K) under the
centre support bar(O), with bolts(2) and nuts(3), tighten them with spanner(7) and screw driver(8).
Attach gas strut to pneumatic frame. First remove the screw on the cross bar of the pneumatic frame, then place
the circle end of the gas strut over the barrel nut and replace screw loosely. Place the hook end of the strut support
over the barrel nut, between the gas strut and cross bar, and finally re-tighten the screw.
5Item code 72840
11 8sets
12 2 pcs
J
2
7
8
11
11
12
12
33
O
EE
M
D
8
3
3
7
2O
K
J
J
J
J
O
K2pcs

K
37
2
8
2 6 pcs
3 6 pcs
7 1 pc
8 1 pc
Step5
Step6
K
Q
Q
1
6
1 4pcs
6 1pc
Attach the centre support bar(Q) to the side rails (C) with bolts (1), and tighten all bolts holding side rails to
Headboard and Footboard from step 2.
Put the metal frame assembled in Step 3 onto the pneumatic frame, and attach with screws (2) and nuts(3) using
Spanner (7) and Screwdriver (8).
6Item code 72840

N
FG
H
N 1pc
P 1 pc
F 30 pcs
G 30 pcs
H 15 pcs
Step7
Step8
N
P
7
3
10
6
10 2pcs
3 2pcs
7 1pc
6 1pc
Attach hook (N) to Platform Top Rail (M) and handle (P) to Platform Bottom Rail (D)
with bolts (10) and nuts (3) using Spanner (7) and Allen Key (6).
Attach an end cap(G) onto one end of every slat (F), 1 per slat. Attach 2 slat pieces together using middle cap(H) to
form 14x slat pairs. Ensure the pins on the caps all face down as shown. Attach the slat pairs to the bed as shown below.
Push the cap pins into the holes to secure slats.
7Item code 72840

Assembly Is Complete
CAUTION
ALWAYS LIFT YOUR BEDS WHEN MOVING/RELOCATING -
DO NOT DRAG. DRAGGING CAN CAUSE THE CENTRE
SUPPORT LEG TO BENT/BREAK.
8 Item code 72840

Product Name: KHYBER QUEEN LIFT BED
Item Code: 72840
REGULAR CARE:
· Protect from direct sunlight
· Vacuum regularly using low suction
· Rotate reversible cushions regularly
· Avoid exposure to new clothing, cushions or throws as this may lead to dye
transfer and permanent staining
CLEANING:
· Do not remove cushion covers for separate cleaning even though they may have zippers
· Do not wash, Do not dry clean, Do not shampoo clean
· Clean only with hot water extraction machine. Professional cleaning recommended
· Do not use dishwashing liquid or laundry detergent. Use only upholstery detergents
· Do not wet filling
· Dry in shade away from direct heat and sunlight
· Allow to dry thoroughly before re-use
SPOT CLEANING:
· Do not rub
· Do not spot clean with any solvent
· Treat spills and stains as soon as possible
· Gently scrape off any soil or blot any liquid from the surface of the fabric before
applying cleaner
· Apply proprietary cleaning agents strictly according to instructions to remove the
residue of the spill
· Do not saturate the fabric or interior with water or other cleaning liquids
WARNING:
· Apply only water-based soil resist (fabric protection) treatments. Do not use
aerosol products
* PILLING IS NOT A FABRIC DEFECT OR FAULT AND IS NOT COVERED
BY WARRANTY
* PILLING IS A NORMAL OCCURRENCE CAUSED BY WEAR AND TEAR AND
DOES NOT AFFECT THE DURABILITY OR FUNCTIONALITY OF THE FABRIC
AND IS EASILY REMOVED
PRODUCT CARE
Made In China
Imported By
Amart Furniture Pty Ltd
Brisbane, Qld, Australia
Item Code: 72840
Product Name: KHYBER QUEEN LIFT BED
9Item code 72840