Amart Furniture SIGNATURE 64529 User manual

ASSEMBLY INSTRUCTION
LA SALLE DRESSER WITH MIRROR
ITEM CODE 64529
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
1
CAUTION: HEAVY ITEM

IMPORTANT: CARE GUIDE FOR YOUR
TIMBER FURNITURE
1
•Congratulations! You have just purchased a quality product from
Amart Furniture. Please read on for important information regarding
your purchase.
•A multi-step finish is applied to all our furniture, but all wood comes
from nature. Because of this, there will be natural variations in
surface texture and grain like knots, mineral streaks and sap runs that
may affect the finish.
•These differences in character are not defects, but distinctions that
make each piece of furniture unique.
•Our furniture is built to last. Following these steps for basic care
should protect your investment for years to come.
•Dust frequently with a clean damp lint-free cloth. This will help
remove abrasive build up which can damage a finish over time.
•Do not place hot objects on any furniture surface. Always use a
coaster or placemat. Laminate and lacquer finishes on table tops
provide added scratch and heat resistance to our furniture, but they
can still be damaged without proper care.
•Avoid exposing your furniture to strong sunlight, heat outlets, open
windows or dampness. Prolonged exposure to direct sunlight can fade
the finish of your furniture, while extreme temperature and humidity
changes can cause cracking or splitting.
•Do not expose your furniture to any liquids. Never allow water to sit
on your furniture. Alcohol, nail polish and perfume are also dangerous
as they will dissolve the lacquer finish on contact and may require
professional repairs.
•Do not allow plastic to come in direct contact with your furniture.
Chemicals in the plastic of placemats etc may soften and mark the
finish if left in contact with the furniture for a period of time.
2

PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to
the point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
2
Allow at least 15min you will need 2 people
23

Part
DESCRIPTION
Qty
In box
1
DRESSER
1
1
2
MIRROR
1
2
3
SUPPORT BAR
2
2
PARTS LIST
3
A
M6 X 45 BOLT
10
PCES
B
M6.5 X 19 FLAT
WASHER
10
PCES
C
M6.5 X 9
SPRING
WASHER
10
PCES
D
ALLEN KEY
1 PCE
4

Step 1
You will need to assemble the M6 x 45 bolts (item A) with the
M6.5 x 9 spring washers (item C) and the M6.5 x 19 flat
washers (item B)
A
M6 X 45 BOLT
4
PCES
B
M6.5 X 19 FLAT
WASHER
4
PCES
C
M6.5 X 9
SPRING
WASHER
4
PCES
D
ALLEN KEY
1 PCE
YOU WILL NEED
4
Step 2
Attach a support bar (Part 3) to the Dresser as shown using 2
of the assembled sets from Step 1, using allen key (item D).
Step 3
Repeat for other support bar.
5

5
Step 4
Next you will need to assemble the M6 x 45 bolts (item A) with the
M6.5 x 9 spring washers (item C) and the M6.5 x 19 flat washers (item
B).
A
M6 X 45 BOLT
6
PCES
B
M6.5 X 19 FLAT
WASHER
6
PCES
C
M6.5 X 9
SPRING
WASHER
6
PCES
D
ALLEN KEY
1 PCE
Step 4
With one person holding the mirror in place, fasten the 6 bolt sets
from step 4, onto the mirror support bar as shown.
6

6
Removing the handles
Handles are installed on the inside for their own protection
during transport. You will need to unscrew them and reattach
them before use.
Step 1
Start by opening drawer with the string attached. Take a
Phillips head screw driver and turn the screws counter
clockwise. Take and store the screw safely once it is loose. As
per the diagram on the left
Step 2
Re-insert the screw from the inside. Hand turn the handle on
the screw until it is secure, then tighten with a Phillips head
screw driver until firmly fixed, as per the diagram on the
right.
7

Attaching the anti-tipping kit.
As wall types vary, we do not supply the screws that you will need, to
fasten onto your wall. Please seek advice from you trusted local
specialist.
Step 1
Attach one of the anchors to the back of the dresser.
Step 2
Mark the spot on the wall that will best line up with the anchors
already fixed on the unit. For best results we recommend placing the
wall anchor to one side and not directly inline with the unit anchor.
Step 3
After sourcing the correct screw system for your wall type, fasten the
wall side of the anchor.
Step 4
Move the unit into position and lock the uni anchor to the wall anchor
together with the cable tie supplied. Do for each anchor point on the
unit.
78

89
Assembly is complete