Amart Furniture NARA 72815 User manual

Imported by Amart Furniture Pty Ltd,Brisbane ,Qld Australia.
For any assistance with assembly or for missing parts please phone Amart
Furniture, Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
NARA QUEEN BED
ITEM CODE 72815
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please
phone Amart Furniture , Customer Service Free call 1800 351 084
1ITEM CODE 72815

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lifting. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
2 ITEM CODE 72815
Allow 20 min For 2 person Additional tools required
X2

3ITEM CODE 72815
PARTS LIST
1 SUPPORT BAR
2 FOOTBOARD
3 FOOTBOARD LEG
4 FOOTBOARD LEG
5 SIDE RAIL
6 SIDE RAIL
7 SUPPORT LEG
8 HEADBOARD SUPPORT BOARD
9 SUPPORT LEG
10 CENTRE RAIL
11 SLATS
12 HEADBOARD
13 HEADBOARD LEG

4ITEM CODE 72815
STEP 1:
Attach the footboard legs(3)(4) to footboard(2) with
bolt (D) and washer (E) using allen key (G).
Note that the footboard legs are divided into left and
right, please install them as show in the figure.

ITEM CODE 72815
5
STEP 2:
STEP 3:
Attach the support bar(1)to footboard(2) with bolt (D) and
washer (E) using allen key (G).
Note the side with a hole in the middle of the bar is upward.
Attach headboard legs (13) to headboard (12) with bolt (D)
and washer (E)using allen key (G)

ITEM CODE 72815
6
STEP 4:
STEP 5:
6
Insert dowel (A) to siderails (5)(6)
Fix angle irons(F) to siderails (5)(6) with bolt (C) and washer
(E) using allen key (G)

ITEM CODE 728157
STEP 6:
STEP 7:
Attach siderails (5)(6) to footboard (2) with bolt (C) and
washer (E) using allen key (G)
Attach the headboard support board(8) to siderails (5)(6)
with hexagon socket screw (I) and nut (J) using allen key (K)

ITEM CODE 72815
8
STEP 8:
STEP 9:
Attach support leg (7) to headboard support board (8) with
bolt (D) and washer (E) using allen key (G)
Attach headboard support board(8) to headboard legs (13)
with bolt (D) and washer (E) using allen key(G)

ITEM CODE 728159
STEP 10:
Attach support legs(9) to centre rail(10) with screw (H) using
allen key (G).
Attach centre rail(10) to support leg(7) and support bar(1) with
bolt (D) and washer (E), using allen key (G).

10 ITEM CODE 72815
STEP 10:
ASSEMBLY IS COMPLETE
CAUTION
Always Lift Your Bed When Moving /Relocating - Do Not
Drag. Dragging Can Cause The Centre Support Legs To
Bend/Break.
Attach slats (11) to the existing unit using screws (B).

To protect your furniture,we suggest the following:
•Avoid placing your furniture in direct sunlight.
•Do not place furniture directly under windows.
•Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
•Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
•Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
11 ITEM CODE 72815