Amart Furniture AG1 User manual

Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
AG1 Gaming Chair
ITEM CODE 66360
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
1-8 66360

PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to
the point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
2-8 66360
X2
ADDITIONAL TOOLS REQUIRED

PARTS LIST
1 HEADREST
2 BACK
3 LUMBAR PILLOW
4 ARMREST(L)&(R)
5 REGULATOR
6 SEAT
7 MECHANISM
8 GAS LIFT COVER
9 GAS LIFT
10 BASE
11 CASTOR
3-8 66360
10
11
Allen key
Bolt Bolt
Rubber cover
Regulator housing
Bolt
A CB
D E
1 PC 2 PCS

STEP
1:
1. Insert castor
⑪into base ⑩.
2. Put gas lift
⑨into base ⑩, then put gas lift cover on gas
lift as shown.
STEP
2:
Attach the mechanism
⑦to the seat using bolt B and fasten
with the Allen key D.
4-8 66360
6
8
9
7
10
11
B

STEP
3:
Attach the armrest
④to seat ⑥using bolt A and fasten
with the Allen key D.
STEP
4:
Attach the regulator
⑤to the back ②
using bolt B. Then
fasten with the Allen key D as shown.
5-8 66360
46
A A
2
6
5

6-8 66360
STEP
5:
Cover the cover E of regulator using Bolt C, and fasten with
Cross wrench D,then cover bolt with rubber cover.
STEP
6:
Put the chair mechanism
⑦on the gas lift ⑨as shown.
7
9
E
E

7-8 66360
STEP 7:
Installation method for the top pillows and lower pillows.
STEP 8:
ASSEMBLY IS COMPLETE
Top pillows installed Lower pillows installed
1.Pass both ends of the adjustment
strap through the seat back hole.
2.Fasten both ends of the adjustment strap.
Adjustment strap
2.Pull the adjustment strap and
fasten it.Repeat the above operation
for the second adjustment strap.
Figure 2
Figure 1
Figure 2
Figure 1
Adjustment strap
1.Move the adjustment strap
across the back of the chair where
it is attached to the seat.

GENERAL PRODUCT CARE
●DO NOT STAND ON THIS CHAIR-DO NOT USE THIS CHAIR AS STEP LADDER.
●USE THIS PRODUCT ONLY FOR SEATING ONE PERSON AT A TIME.
●DO NOT USE THIS CHAIR UNLESS ALL BOLTS, SCREWS AND KNOBS ARE
FIRMLY SECURED.
●AT LEAST EVERY 4 MONTHS, CHECK ALL BOLTS, SCREWS AND KNOBS TO
BE SURE THEY ARE TIGHT.
●IF PARTS ARE MISSING, BROKEN, DAMAGED OR WORN, STOP USE THE
PRODUCT UNTIL REPAIRS ARE MADE. USING FACTORY AUTHORIZED PARTS.
●FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY.
8-8 66360
CARE AND MAINTENANCE
OFFICE CHAIR
DO NOT REMOVE THIS LABEL