AMASE AUDIO BMW E46 7inch Android User manual

Installation manual
Are you ready to install our unit?
Let's go >>>
BMW E46 7inch Wince
V2

23
5 steps to install
STEP
STEP
STEP
STEP
STEP
STEP
01
01
02
03
04
05
Do the full installation.
Test the head unit functions.
Test your unit before installing
into your car
(Connect the power cable to your car)
Check
1) Do the screen is broken ?
2) Do the accessories have missing ?
Double check if has any
missing before installation.
Double check if has any
missing before installation.
In this case, the installation
can't be plug & play if your
car dash radio plug is
same as shown on the right
picture.
You need to seperately
purchase an extension
harness for connecting the
head unit and the BM54/24
amp in the trunk area.
5m extended harness
Please nd the ASIN in the listing.

45
The references of BM54 tuner location
Installation guide
If you are in above three situations,
your car should be built-in an amplier
- BM54/24 tuner in the trunk area. You
need to use the extended harness to
connect both of them.
Installation steps
1. Connect the power plug to the new head unit.
2. pull the extension harness to the trunk area as
shown.
3. Connect the female radio plug of your car with
the male plug of extended harness.
From extended harness

67
4. Connect the female plug of extension harness
with the amplier - BM54/24 tuner.
From
extended harness
If the factory plug like
below(only 17pin and
lack of 4pin). It's not
compatible with our
Amaseaudio head unit.
1. User Manual *1
2. External Miscrophone *1
3. GPS antenna *1
4. USB Adapter cable *1
5. Canbus *1
6. Radio Antenna connector *1
7. USB Adapter cable *1
8. Power cable *1
9. USB Adapter cable *1
10. Disassembly tool *1
Accessories
1
2
3
4
5
67
8
9
10

89
1. Double check the size and shape of the center console
panel.
4. Remove the 2 xed
screws on the factory
CD player with a Philips
screwdriver.
2. Pry the decoration strip
from edge with the plastic tool
3. Take out the decoration
strip
5. Take out the factory CD player, the AC controller and
the storage box.
6. Replace the AC controller to the place of storage box.
Now you can take out the power cable to connect the
head unit and then try to turn it on. If this part is no
problem, you can do the remain steps.
STEP
03
Test your unit before installing
into your car
(Connect the power cable to your car)
STEP
04 Do the full installation.

10 11
Wiring diagram
8. Connect those wires provided in the package like (1)
Power cable with canbus, (2) USB cable, (3) Radio antenna
adapter cable, (4) GPS antenna (5) External microphone
and (6) RCA cable as shown.
7. Remove the 4 xed screws of the factory mounting bracket
with a Philips screwdriver and take out the bracket
1
234
5
6

12 13
15. Plug the head unit into the center console, then place
the GPS antenna and microphone as shown. The wires are
hidden in the side of pillar trim and led to the head unit.
STEP
05 Test the head unit functions.
(FM, SD, USB, Bluetooth, reversing, handbrake,
headlight, steering wheel control and etc)

14
Optional : Reverse camera installation instruction
Trouble Shooting:
1. Conrm that all the lines are connected. The car is hung to the
reverse gear and the display switches to the reverse mode. If the
screen does not switch, please check whether the reverse detection
line is connected to the reverse lamp power supply line and has a
voltage of about 12V. If not, please connect it perfectly.
2. When the car is in the reverse gear position and the display switches
to the reverse model but there is no video display, then check that the
camera power supply and video signalcable are correctly connected to
the reverse video signal line input plug(CAMERA IN) on the machine.
Connect with "CAMERA IN"
cable of the Car Radio
Red cable connect with
"REVERSE" cable of the
power cable
Two red cables connect
together.