AMASE AUDIO BMW E46 7inch Android User manual

Installation manual
Are you ready to install our unit?
Let's go >>>
V2
BMW E46 7inch Android

23
In this case, the installation
can't be plug & play if your
car dash radio plug is
same as shown on the right
picture.
You need to seperately
purchase an extension
harness for connecting the
head unit and the BM54/24
amp in the trunk area.
5m extended harness
Please nd the ASIN in the listing.
5 steps to install
STEP
STEP
STEP
STEP
STEP
STEP
01
01
02
03
04
05
Do the full installation.
Test the head unit functions.
Test your unit before installing
into your car
(Connect the power cable to your car)
Check
1) Do the screen is broken ?
2) Do the accessories have missing ?
Double check if has any
missing before installation.
Double check if has any
missing before installation.

45
The references of BM54 tuner location
Installation guide
If you are in above three situations,
your car should be built-in an amplier
- BM54/24 tuner in the trunk area. You
need to use the extended harness to
connect both of them.
Installation steps
1. Connect the power plug to the new head unit.
2. pull the extension harness to the trunk area as
shown.
3. Connect the female radio plug of your car with
the male plug of extended harness.
From extended harness

67
4. Connect the female plug of extension harness
with the amplier - BM54/24 tuner.
From
extended harness
If the factory plug like
below(only 17pin and
lack of 4pin). It's not
compatible with our
Amaseaudio head unit.
1. Power cable *1
2. GPS antenna *1
3. USB adapter cable *1
4. Wi-Fi antenna *1
5. External microphone *1
6. Canbus *1
7. USB adapter cable *1
8. USB adapter cable *1
9. Radio antenna connector *1
10. Disassembly tool *1
11. 3M adhesive *1
12. 15A fuse *1
13. Radio antenna adapter *1
14. Long screw *2
15. A&V output harness *1
16. Disassembly key *2
17. Warrenty card *2
17
Accessories

89
1. Double check the size and shape of the center console
panel.
4. Remove the 2 xed
screws on the factory
CD player with a Philips
screwdriver.
2. Pry the decoration strip
from edge with the plastic tool
3. Take out the decoration
strip
5. Take out the factory CD player, the AC controller and
the storage box.
6. Replace the AC controller to the place of storage box.
Now you can take out the power cable to connect the
head unit and then try to turn it on. If this part is no
problem, you can do the remain steps.
STEP
03
Test your unit before installing
into your car
(Connect the power cable to your car)
STEP
04 Do the full installation.

10 11
8. Connect those wires provided in the package like (1)
Power cable with canbus, (2) USB cable, (3) Radio antenna
adapter cable, (4) GPS antenna, (5) Wi- antenna and (6)
External microphone as shown.
1
2
2
3
4
65
7. Remove the 4 xed screws of the factory mounting bracket
with a Philips screwdriver and take out the bracket Wiring diagram

12 13
9. Plug the head unit into the center console, then place
the GPS antenna and microphone as shown. The wires are
hidden in the side of pillar trim and led to the head unit.
STEP
05 Test the head unit functions.
(FM, SD, USB, Bluetooth, reversing, handbrake,
headlight, steering wheel control and etc)
Wire connection for the amplier, the subwoofer
and the headset monitors

14 15

16 17
Below is our rear camera. This will be a reference to teach
you how to connect a rear camera to our head unit.
The ASIN of this rear camera
has placed in the listing.
Optional : Install a rear camera System Initial setup
1
2
Set radio location
Set RDS
The default radio country in the unit is Europe, if you
are from other country, you need to access the "factory
mode (PW: 126) > Radio" to adjust the country.
The Radio has RDS function but this function is only
for Europe, if the clients from other countries use it, it
will affect the radio receival, so please close it.

18
Q: Do my head unit has one year maintanence?
A: Denitely yes, you will have our commitment
after you purchase.
(The maintainence period will base on the date you
make the order)
About after sales service
Set the unit language
Please go to setting > Languages & input, then you
can add the desirable language you need.
3