AmazonBasics MP0070 User manual

INSTRUCTION MANUAL
UNIVERSAL PROJECTOR MOUNT
Maximum Load: 15 kg (33 lbs)
Tilt Range: - 15° to 15° up/down
Swivel Range: up to 360°
Distance from Ceiling: 12.8 cm (5.0”)
Read these instructions before you begin. If you are unsure
of any part of the process, contact a professional contractor or
installer for assistance. Improper installation can result in injury
or damage.
The ceiling or mounting surface must be capable of
supporting the combined weight of the mount and the
projector; if not, the structure must be reinforced.
Locate pipes, wires, or any other hazards in the area where you
wish to install the mount before drilling.
Safety gear and proper tools must be used. Failure to do so
can result in injury or damage.
Follow all instructions and recommendations regarding
adequate ventilation and suitable locations for mounting your
projector. Consult the owner‘s manual for your particular
display for more information.
CAUTION: This mount is intended for use only with the
maximum weight of 15 kg (33 lbs). Use with heavier than the
maximum weights indicated may result in instability causing
possible injury.
1
2
3
4
(A) Wood Screw M6.3 x63 (x2)
(B) Wall Anchor (x2)
(C) M3 x12 (x4)
(D) M4 x 12 (x4)
(E) M5 x 10 (x8)
(F) M5 x 12 (x4)
(G) M6 x 12 (X8)
(H) M5 Washer (x4)
(I)M4 Washer (x4)
(J) M5 small washer (x2)
(K) M6 Washer (x4)
(L) M5 larger washer (x4)
(M) M5 plastic washer (x4)
5
SPECIFICATIONS
BOX CONTENTS
HARDWARE KIT
TOOLS REQUIRED
WARNINGS
Phillips Head Screw Driver
Electric or Portable Drill
3 mm (1/8”) Drill Bit and Stud Finder for Drywall Installation
8 mm (5/16”) Masonry Bit for Concrete Installation
Ceiling Plate (x1)
Mount Body (x1)
Mount Base (x1)
Extension arm (x4)
Instruction Manual (x1)
Hardware Kit (x1)
Attach the M5 large washer (L)
to the Mount Body using the M5
x 10 screw (E) from the kit (see
Fig. 2). Leave the screw loose
enough so that the mount can
be hooked onto the mount
body.
Use a high-quality stud finder to
locate a ceiling joist where you wish to install your mount.
Mark both edges of the joist to help identify the exact center.
Wood studs should be 2” x 4”, at minimum:1.5”x 3.5” (38mm x
89mm) (see Fig. 3).
2
Place the ceiling plate over the
joist and mark two locations for
securing the plate to the ceiling
(see Fig. 4).
Set the ceiling plate aside and
drill two holes 2.5” (64 mm) deep
using a 1/8” (or 3 mm) size drill
bit at each marked location.
4
Install the ceiling plate using
two lag Bolts (A) in the “A” and “B”
holes. Do not over tighten lag
Bolts (see Fig. 5).
6
5
Attach the Mount Body to the
ceiling plate using the M5 x 10
screw (E), M5 small washer (J),
M5 plastic washer (M) from the
kit (see Fig. 1).
1
3
Part 1A – Mounting to the Ceiling (Drywall)
Part 1A – Mounting to the Ceiling (Drywall) (continued)
INSTALLATION
Part 1B –Mounting to the Ceiling (Concrete)
(E)
(M)
(J)
Attach the mount body to the
ceiling plate using the M5 x 10
screw (E), M5 small washer (J),
M5 plastic washer (M) from the
kit (see Fig. 6).
1
(E)
(M)
(J)
(E)
(L)
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
(A)

Part 2 – Attaching the Projector to the Mount
XXXX-20181008
1Swivel adjustment can be made by simply turning your
projector in the desired direction (see Fig. 16).
OPERATION AND ADJUSTMENT
Examine the mounting holes on
the back of your projector to
determine the extension arm
needed or not.You may need to
remove the fixing screw on the
extension arm to shorten the
extension arm for smaller
projector(see Fig. 11).
1
Hook the mount base with your projector attached onto the
mount body. Tighten the M5 x 10 screws (E) on the sides of
the mount base to hold it in place (see Fig. 15).
1
Attach your projector to the mount arms as shown using the
appropriate screw from the hardware kit (C, D, F and G) (see
Fig. 13)．
3
Attach the mount arms to the mount base as shown using the
M6 x 12 screws (G) and M6 washer (K) from the kit. Attach one
mount arm into each slot in the mount base (see Fig. 12).
Leave the screws loose enough so that the arms can be
moved when attaching the projector.
2
Tighten the M6 x 12 screws (G) used to attach the arms to the
mount base in step 1 (see Fig. 14).
NOTE: If you cannot find a screw from the
provided hardware kit that fits, consult the
manufacturer of your display for the
proper size.
Part 2 – Attaching the Projector to the Mount (continued)
Part 3 – Assembling the Mount
4
2
3
Attach the M5 large washer (L)
to the Mount Body using the M5
x 10 screw (E) from the kit (see
Fig. 7). Leave the screw loose
enough so that the mount can
be hooked onto the mount
body.
After you have determined your
desired Projector location, Place
the ceiling plate over the joist
and mark two locations for
securing the plate to the ceiling.
4
5
6
Set the ceiling plate aside and
drill two holes 3”(76mm) deep
using a 5/16”(or 8mm) size drill
bit at each marked location (see
Fig. 8).
Insert concrete anchors (B) into
each hole so that it is flush with
the concrete surface. A hammer
can be used to lightly tap the
anchors into place if necessary
(see Fig. 9).
Install the Ceiling Plate using
two Lag Bolts (A) in the “A” and
“B” holes. Do not over tighten lag Bolts (see Fig. 10).
Part 1B – Mounting to the Ceiling (Concrete)(continued)
(G) (C or D or F)
(I or H)
C I
D I
F H
(E)
(A)
360°
2Tilt adjustments can be made by loosening the screws on
both sides of the ceiling plate and mount base, moving the
projector to the desired angle, and then re-tightening the
screws (see Fig. 17).
3Periodically clean your mount with a dry cloth. Inspect all
screws and hardware at regular intervals to ensure that no
connections have become loose over time. Re-tighten as
needed.
±15°
±15°
Fig. 8
Fig. 9
Fig. 10
Fig. 11
(G)
(K)
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 17
Fig. 16
(E)
(L)
Fig. 7