amber connect Amber Covert T200 User manual

Know your device
AGT 200 Device view
Pinout
AGT200 pinout
Pin
number
Pin name
Description
1
GND (-)
Ground
2
CAN 1L
SAE J1939 CAN interface Low channel 1
3
1WIRE POWER
Power supply pin for Dallas 1-Wire® devices
4
DIN4
Digital input, channel 4
5
DIN2
Digital input, channel 2
6
CAN 2L
SAE J1939 CAN interface Low channel 2
7
AIN2
Analog input, channel 2. Input range: 0-30V/0-10V DC
8
DOUT3
Digital output. Open collector output
9
DOUT2
Digital output. Open collector output
10
AIN3
Analog input, channel 3. Input range: 0-30V/0-10V DC
11
VCC (+)
Power supply (+10-30 V DC)
12
CAN 1H
SAE J1939 CAN interface High channel 1
13
1WIRE DATA
Data channel for Dallas 1-Wire® devices

14
DIN3
Digital input, channel 3
15
IGN (DIN1)
Digital input, channel 1. DEDICATED FOR IGNITION
INPUT
16
CAN 2H
SAE J1939 CAN interface High channel 2
17
AIN1
Analog input, channel 1. Input range: 0-30V/0-10V DC
18
DOUT4/AIN4
Digital output. Open collector output OR Analog input,
channel 4. Input range: 0-30V/0-10V DC
19
DOUT1
Digital output channel 1. Open collector output
20
K-Line
K-LINE interface for online Tachograph Vehicle Data
transfer
Wiring scheme
AGT 200 Wiring scheme
Set up your device
How to insert Micro-SIM card and connect the battery
1. Unscrew 4 screws counter clockwise that are located on the bottom of the device.
2. Remove the cover.
3. Insert SIM card as shown with PIN request disabled or read Security info how to enter it later in
Amber Configurator. Make sure that SIM card cut-off corner is pointing forward to slot. SIM slot 1
is closer to PCB, SIM slot 2 is the upper one.
4. Connect battery as shown to device.
5. After configuration, see “PC Connection (Windows)”, attach device cover back
6. Screw in all screws. Device is ready to be mounted.

Unscrew screws Cover removal
SIM card insert Battery connection
Mounting recommendations
•Connecting wires
1. Wires should be connected while the module is not plugged in.
2. Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and
moving objects near the wires.
3. The connections should not be seen very clearly. If factory isolation was removed while connecting
wires, it should be applied again.
4. If the wires are placed in the exterior or in places where they can be damaged or exposed to heat,
humidity, dirt, etc., additional isolation should be applied.
5. Wires cannot be connected to the board computers or control units.
•Connecting power source
1. Be sure that after the car computer falls asleep, power is still available on chosen wire. Depending
on car, this may happen in 5 to 30 minutes period.
2. When the module is connected, measure the voltage again to make sure it did not decrease.
3. It is recommended to connect to the main power cable in the fuse box.

4. 3 A, 125 V external fuse
•Connecting ignition wire
1. Be sure to check if it is a real ignition wire power does not disappear while starting the engine.
2. Check if this is not an ACC wire (when key is in the first position, most electronics of the vehicle
are available).
3. Check if power is still available when you turn off any of vehicles devices.
4. Ignition is connected to the ignition relay output. As alternative, any other relay, which has power
output when ignition is on, may be chosen.
•Connecting ground wire
1. Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
2. If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
3. For better contact scrub paint from the spot where loop is going to be connected.
PAY ATTENTION! Connecting the power supply must be carried out in a very low impedance point of on-board vehicle network.
Connecting the GND at an arbitrary point to the mass of the car is unacceptable, as static and dynamic potentials on the line
GND will be unpredictable, which can lead to unstable AGT400-M operation and even its failure.
LED indications
Navigation LED indications
Behaviour
Meaning
Permanently switched on
GNSS signal is not received
Blinking every second
Normal mode, GNSS is working
Off
GNSS is turned off because: Device is not working or Device
is in sleep mode
Blinking fast constantly
Device firmware is being flashed
Status LED indications
Behaviour
Meaning
Blinking every second
Normal mode
Blinking every two seconds
Sleep mode
Blinking fast for a short time
Modem activity
Off
Device is not working or Device is in boot mode

Characteristics
Basic characteristics
Module
Name
AGT 200
Technology
GSM ,GPRS, GNSS, BLUETOOTH
GNSS
GNSS
GPS, GLONASS, GALILEO, BEIDOU, QZSS, DGPS
Receiver
Tracking: 33/99 acquisition channels
Tracking sensitivity
-165 dBM
Accuracy
< 3 m
Hot start
< 1 s
Warm start
< 25 s
Cold start
< 35 s
Cellular
Technology
GSM/GPRS
2G bands
Quad-band 850/900/1800/1900 MHz
GPRS
GPRS Mobile Station Class B
Data transfer
GPRS Multi-Slot Class 12 (up to 240 kbps)
Data support
SMS (text/data)
Power
Input voltage range
10-30 V DC with overvoltage protection
Back-up battery
550 mAh 8,4V Ni-MH battery
2 W max. Current consumption
at 12 V
GPRS: average 69 mA
Nominal: average 39 mA
GNSS sleep: average 24 mA
Deep Sleep: average 7.5 mA
Online Deep Sleep: average 2.4 mA
2 W max. Current consumption
at 24 V
GPRS: average 35 mA
Nominal: average 20 mA
GNSS sleep: average 12,5 mA
Deep Sleep: average 3,8 mA
Online Deep Sleep: average 1.3 mA
Interface
Digital Inputs
4
Digital Outputs
4
Analog Inputs
4
1-Wire temperature sensors
6
1-Wire iButton
1
RS232
2
RS485
1
CAN J1939
2
J1708
1
K-Line
1
LVCAN/ALLCAN
1
GNSS antenna
External High Gain
GSM antenna
External High Gain
USB
2.0 Mini-USB
LED indication
2 status LED lights
SIM
2x SIM Card (Dual-SIM)

Memory
2MB internal flash memory and Micro-SD card
Bluetooth
Specification
4.0 + LE
Supported peripherals
Headset, Inateck Barcode Scanner
Features
Sensors
Accelerometer
Scenarios
Green Driving, Over Speeding detection, Jamming
detection, Excessive Idling detection, Crash detection,
Immobilizer, iButton Read Notification, Towing detection,
Functionalities
Crash detection, Auto Geofence, Manual Geofence, Trip
Detection, Odometer, DDD download and Tacho Online
Data
Sleep modes
GPS Sleep, Online Deep Sleep, Deep Sleep
Configuration and firmware update
FOTA Web, FOTA, Amber Configurator (USB, Bluetooth),
FMBT mobile application (Configuration)
SMS
Configuration, Events, DOUT control, Debug
GPRS commands
Configuration, DOUT control,
Time Synchronization
GPS, NITZ, NTP
Fuel monitoring
LLS (Analog), LV-CAN, ALL-CAN, CAN FMS,
RS232/RS485 Fuel Sensor, Ultrasonic level sensor
Ignition detection
Digital Input , Accelerometer, External Power Voltage
Physical specification
Dimensions
104,1 x 76,8 x 31,5 mm (L x W x H)
Weight
197 g
Operating environment
Operating temperature (without
battery)
-40 °C to +85 °C
Storage temperature (without battery)
-40 °C to +85 °C
Operating humidity
5% to 95% non-condensing
Ingress Protection Rating
IP41
Electrical characteristics
Characteristic description
Value
Min.
Typ.
Max.
Unit
Supply Voltage
Supply Voltage (Recommended
Operating Conditions)
+10
+30
V
Digital Output (Open Drain grade)
Drain current
(Digital Output OFF)
120
μA
Drain current (Digital Output
ON, Recommended Operating
Conditions)
0.5
A
Static Drain-Source resistance (Digital
Output ON)
400
300
mΩ

Digital Input
Input resistance (DIN1)
15
kΩ
Input resistance (DIN2)
15
kΩ
Input resistance (DIN3)
15
kΩ
Input resistance (DIN4)
15
Input voltage (Recommended Operating
Conditions)
0
Supply
voltage
V
Input Voltage threshold (DIN1, DIN2,
DIN3,DIN4)
7.5
V
Input Voltage threshold (DIN2, DIN3,
DIN4)
7.5
V
Analog Input
Input voltage (Recommended Operating
Conditions), Range 1
0
+10
V
Input resistance
120
kΩ
Input Voltage (Recommended Operating
Conditions), Range 2
0
+30
V
Input resistance
147
kΩ
1-Wire
Supply voltage
+3.3
+3.9
V
Output inner resistance
7
Ω
Output current (Uout > 3.0 V)
30
mA
Short circuit current (Uout = 0)
75
mA
CAN Interface
Internal terminal resistors CAN bus
120
Ω
Differential input resistance
19
30
52
kΩ
Recessive output voltage
2
2.5
3
V
Differential output voltage
0.5
0.7
0.9
V
Common mode input voltage
-30
30
V
Safety information
This message contains information on how to operate AGT 200 safely. By following these
requirements and recommendations, you will avoid dangerous situations. You must read
these instructions carefully and follow them strictly before operating the device!
•The device uses SELV limited power source. The nominal voltage is +12 V DC. The
allowed voltage range is +10...+30 V DC.
•To avoid mechanical damage, it is advised to transport the device in an impact-proof
package. Before usage, the device should be placed so that its LED indicators are
visible. They show the status of device operation.
•When connecting the 2x10 connector wires to the vehicle, the appropriate jumpers of the
vehicle power supply should be disconnected.
•Before dismounting the device from the vehicle, the 2x10 connector must be disconnected.
•The device is designed to be mounted in a zone of limited access, which is inaccessible to the
operator. All related devices must meet the requirements of EN 62368-1 standard.
•The device AGT 200 is not designed as a navigational device for boats.

Do not disassemble the device. If the device is damaged, the power supply cables
are not isolated or the isolation is damaged, DO NOT touch the device before
unplugging the power supply.
All wireless data transferring devices produce interference that may affect other
devices which are placed nearby.
The device must be connected only by qualified personnel.
The device must be firmly fastened in a predefined location.
The programming must be performed using a PC with autonomic power supply.
Installation and/or handling during a lightning storm is prohibited.
The device is susceptible to water and humidity.
Certification and Approvals

•AGT400-M CE / RED
•AGT400-M CE E-Mark
•AGT400-M CE REACH
•AGT400-M CE Declaration of IMEI assignment
•AGT400-M CE Declaration of device operation temperature
•AGT400-M CE RoHS
•AGT400-M CE EAC
This sign on the package means that it is necessary to read the User‘s Manual
before your start using the device. Full User‘s Manual version can be found in our
Wiki.
This sign on the package means that all used electronic and electric equipment
should not be mixed with general household waste.

Hereby, Amber declare under our sole responsibility that the above described
product is in conformity with the relevant Community harmonization: European
Directive 2014/53/EU (RED).
Warranty
Amber connect guarantees its products to be free of any manufacturing defects for a period of 24
months. With additional agreement we can agree on a different warranty period, for more detailed
information please contact our sales manager.
All batteries carry a reduced 6 month warranty period.
If a product should fail within this specific warranty time, the product can be:
•Repaired
•Replaced with a new product
•Replaced with an equivalent repaired product fulfilling the same functionality
•Amber can also repair products that are out of warranty at an agreed cost.
Warranty Disclaimer
Amber products are intended to be used by persons with training and experience. Any other use renders
the limited warranties expressed herein and all implied warranties null and void and same are hereby
excluded. also excluded from this limited warranty are any and all incidental or consequential damages
including but not limited to, loss of use or revenue, loss of time, inconvenience or any other economic loss.