American Dynamics Illustra Flex Series User manual

Illustra Flex Series
1MP & 3MP Outdoor Dome
Quick Start Guide
8200-1027-10 B0

Illustra Flex 1MP & 3MP Outdoor Dome
2
Notice
Please read this manual thoroughly and save it for future use before attempting to connect or operate this unit.
The information in this manual was current when published. The manufacturer reserves the right to revise and
improve its products. All specifications are therefore subject to change without notice.
Copyright
Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced, translated or
reduced to any electronic medium or machine-readable form, in whole or in part, without prior written consent of
Tyco Security Products. © 2013 Tyco Security Products. All rights reserved.
American Dynamics
6600 Congress Avenue
Boca Raton, FL 33487 U.S.A.
Customer Service
Thank you for using American Dynamics products. We support our products through an extensive worldwide
network of dealers. The dealer through whom you originally purchased this product is your point of contact if you
need service or support. Our dealers are empowered to provide the very best in customer service and support.
Dealers should contact American Dynamics at [phone] or [phone] or on the Web at
www.americandynamics.net.
Trademarks
The trademarks, logos, and service marks displayed on this document are registered in the United States [or
other countries]. Any misuse of the trademarks is strictly prohibited and Tyco Security Products. will
aggressively enforce its intellectual property rights to the fullest extent of the law, including pursuit of criminal
prosecution wherever necessary. All trademarks not owned by Tyco Security Products. are the property of their
respective owners, and are used with permission or allowed under applicable laws.
Product offerings and specifications are subject to change without notice. Actual products may vary from photos.
Not all products include all features. Availability varies by region; contact your sales representative.

Illustra Flex 1MP & 3MP Outdoor Dome
3
Table of Contents
WARNING ........................................................................................................................................................4
Preface.............................................................................................................................................................5
1. Product Overview....................................................................................................................................6
1.1 Physical Characteristics.......................................................................................................................6
2. Installation and Connection ................................................................................................................9
2.1 Unpack Everything...............................................................................................................................9
2.2 Installation............................................................................................................................................9
2.2.1 Checking Appearance............................................................................................................. 9
2.2.2 Disassembling the Camera................................................................................................... 10
2.2.3 Connecting the wires............................................................................................................. 10
2.2.4 Mounting the camera............................................................................................................. 12
2.2.5 Adjusting the camera position............................................................................................... 14
2.2.6 Locking the camera............................................................................................................... 15
2.2.7 Network Topology.................................................................................................................. 15
2.2.8 System Requirements........................................................................................................... 16
2.3 Connection.........................................................................................................................................17
2.3.1 Default IP address................................................................................................................. 17
2.3.2 Connecting from a computer & Viewing Preparation............................................................ 17
2.4 Using the illustra Connect Tool to Manage Cameras.........................................................................20

Illustra Flex 1MP & 3MP Outdoor Dome
4
WARNING
This unit operates at AC 24V/ PoE.
Installation and service should be performed only by qualified and experienced technicians and comply
with all local codes and rules to maintain your warranty.
To reduce the risk of fire or electric shock, do not expose the product to rain or moisture.
Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral detergent and
wipe with a dry soft cloth.
Do not apply benzene or thinner to the camera, which may cause the surface of the unit to be melted or
lens to be fogged.
Avoid aligning the lens to very bright objects (example, light fixtures) for long periods of time.
Avoid operating or storing the unit in the following locations:
Extremely humid, dusty, or hot/cold environments (recommended operating temperature: -40°C to
+50°C) (PoE does not support heater.)
Close to sources of powerful radio or TV transmitters
Close to fluorescent lamps or objects with reflections
Under unstable or flickering light sources
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product
(applicable in the European Union and other European countries with separate collection
systems). This product should be disposed of, at the end of its useful life, as per applicable
local laws, regulations, and procedures.

Illustra Flex 1MP & 3MP Outdoor Dome
5
Preface
This user manual is designed as a reference for the installation and manipulations of the unit including the
camera’s features, functions, and detailed explanation of the menu tree. The reader is supposed to be able to
get following information in the manual.
Product Overview: the main functions and system requirements of the unit.
Installation and Connection: instructions on unit installation and wire connections.
Administration and Configuration: the main menu navigation and controls explanations.

Illustra Flex 1MP & 3MP Outdoor Dome
6
1. Product Overview
1.1 Physical Characteristics
FIGURE 1-1: PHYSICAL DIMENSION A
FIGURE 1-2: PICTORIAL INDEX*
* Refer to table 1-1 for definitions
Unit: mm

Illustra Flex 1MP & 3MP Outdoor Dome
7
TABLE 1-1: PICTORIAL INDEX DEFINITION
Index #
Name
1 Camera bottom case
2 Tilt adjustment bracket and thumbnuts, notches(X2),
3 IR board
4 Loosen the screw to take off camera housing
5 Camera top case
6 Dome cover
FIGURE 1-3: PIN DEFINITIONS 1/2
TABLE 1-2: PIN DEFINITIONS 1/3
DEFAULT return to factory default by press button for 5
seconds
RESET system restart

Illustra Flex 1MP & 3MP Outdoor Dome
8
FIGURE 1-4: PIN DEFINITIONS 2/2
Note Connectors and field wiring terminal for external Class 2 circuits provided with marking
indicating minimum Class of wiring to be used. Class 2 shall be marked adjacent to the field
wiring terminals.
TABLE 1-3: PIN DEFINITIONS 2/3
Au/I Audio in
GND
Au/O Audio out
GND
AI Alarm in
GND
AO Alarm out
COM
TABLE 1-4: PIN DEFINITIONS 3/3
AC 24V Network IR vandal dome camera can operate at AC 24V
only

Illustra Flex 1MP & 3MP Outdoor Dome
9
2. Installation and Connection
2.1 Unpack Everything
Check everything in the packing box matches to the order form and the packing slip. In addition to this
manual, items below are included in the packing box.
One Network IR vandal dome Camera
2-pin terminal block for power input, and 8-pin terminal block for alarm input/output
One CD containing Illustra Connect, user manual and quick installation guide.
One printed quick installation guide
One monitor out cable
One mounting template
One hexagon screw driver
3 screw anchors
3 screws
Please contact your dealer if any item missing.
2.2 Installation
Following tools might help you complete the installation:
a drill
screwdrivers
wire cutters
2.2.1 Checking Appearance
When first unboxing, please check whether if there is any visible damage to appearance of the unit and its
accessories. The protective materials used for the packaging should be able to protect the unit from most of
accidents during transportation.
Please remove the protective film of the unit when every item is checked in accordance with the list
in 2.1 Unpacking Everything.

Illustra Flex 1MP & 3MP Outdoor Dome
10
2.2.2 Disassembling the Camera
Gently remove the screw to take off camera housing (3).
Set the camera housing (4) aside.
FIGURE 2-1: DISASSEMBLING THE CAMERA
2.2.3 Connecting the wires
1. Connect the power cable to the power plugs with one of the following options.
Inset power cable for AC 24V, Connect 24 V (~) cables to terminals ~AC 24V.
PoE: Connect the RJ-45 jack to a PoE compatible network device that supplied power through the
Ethernet cable.

Illustra Flex 1MP & 3MP Outdoor Dome
11
2. Insert Audio cable and alarm cable to the unit, and connect the network cable to the RJ-45 terminal of a
switch.
FIGURE 2-2: CONNECTING THE WIRES
3. Connected the wiring then place the camera to a proper position by pushing the button.
FIGURE 2-3: CONNECTING THE WIRES

Illustra Flex 1MP & 3MP Outdoor Dome
12
2.2.4 Mounting the camera
Place the mounting template sticker (supplied) on the mounting surface and mark three holes according to
the mounting template sticker. Then fasten the anchors to the mounting surface with screws. Next, secure the
unit bottom case (1) to the wall/ceiling with tapping screws as supplied and adjust the view angle (zoom,
focus, and horizontal rotation).
FIGURE 2-4: MOUNTING THE CAMERA
Refer to figure 2-5. Connect the Safety Wire (Fall Prevention Wire, not supplied) with one end to the
wall/ceiling and the other to the safety-cord screw of the unit.
FIGURE 2-5: MOUNTING THE CAMERA
Warning Depending on the material of mounting surface, different screws and anchors than those
supplied may be required. To prevent the unit from falling off, ensure that it is mounted to a
firm place (ceiling slab or channel) using a safety wire strong enough to withstand the total
weight of the unit. (Pay also attention to the finishing at the end of the wire.)
Caution Safety wire must be connected with one end to the wall/ceiling and the other to the
safety-cord screw of the unit.
Safety wire (not supplied).
Please tighten on a firm place as shown.

Illustra Flex 1MP & 3MP Outdoor Dome
13
(Optional) 4S Electrical junction box
1. Secure the mounting kit (optional) to 4S Electrical box using 2 appropriate screws.
2. Secure the unit case to mounting kit using 2 appropriate screws.
3. Tuck the cables in the 4S Electrical box.
4. Adjust the view angles (zoom, focus, and horizontal rotation).
5. Attach the unit housing.
6. Turn the power on after installed the unit.
FIGURE 2-6: MOUNTING THE CAMERA
Note Keeping tilt angel over 25 degrees is recommended when IR-LED light is used. If tilt angel is
below 25 degrees from the horizontal, the image would be flashed by the reflection of IR-LED
light.
The mounting kit is
not supplied

Illustra Flex 1MP & 3MP Outdoor Dome
14
2.2.5 Adjusting the camera position
The unit has three axes for positioning. While screening the picture on the monitor, adjust the position by
procedures below.
Pan Adjustment (A): for wall mount and tilted ceiling rotate the lens base (360° maximum) until satisfied
with the field of view.
Horizontal Rotation (B): rotate 3D assembly in the base, but do not turn assembly more than 360° as
this may have the internal cables twisted, disconnected, or broken.
Tilt Adjustment (C): after loosening the thumbnuts, position the camera as desired, then finger –tighten
the thumbnuts to set the position.
Note
For Outdoor dome series:
Users can adjust zoom level and focus level manually according to the ambient condition.
Caution
Limitation for three axes position:
Pan range: ±175°
Tilt range: 25°～90°
Rotate range: Manual Lens ±180° / Motorize Lens ±175°
FIGURE 2-7: ADJUSTING THE CAMERA POSITION
Caution
Retighten the locking screws to prevent slack after adjustment.

Illustra Flex 1MP & 3MP Outdoor Dome
15
2.2.6 Locking the camera
Use soft, lint -free cloth to wipe the dome cover and remove fingerprints. Attach camera housing. Turn the
power on after you have installed the unit.
2.2.7 Network Topology
The camera can deliver video images and audio in real time using the Internet and Intranet. It's equipped with
Ethernet RJ-45 network interface.
FIGURE 2-8: NETWORK TOPOLOGY TYPE
Ⅰ
FIGURE 2-9: NETWORK TOPOLOGY TYPE
Ⅱ

Illustra Flex 1MP & 3MP Outdoor Dome
16
2.2.8 System Requirements
Below table lists the minimum requirement to implement and operate a Illustra Flex Outdoor Dome.
TABLE 2-1: SYSTEM REQUIREMENTS
System Hardware
CPU Intel Pentium 4 2.4GHz or equivalent
RAM 1 GB
Display NVIDIA GeForce 6 Series or ATI Mobility Radeon 9500
System Software
Operating System Microsoft Windows XP, Windows Vista, or Windows 7
Browser Microsoft Internet Explorer 8 or above
Unit
Power Supply AC 24V / PoE
Networking
Wired* 10/100BASE-T Ethernet (RJ-45 connector)
*a switch is required for surveillance on multiple units.
Note All the installation and operations should comply with your local electricity safety rules.
Caution To avoid damage to the unit, never connect more than one type of power supply (PoE
IEEE802.3 Ethernet Class 0 or AC 24V power plug) at the same time. If using PoE, this
camera is to be connecting only to PoE networks without routing to heterogeneous devices.

Illustra Flex 1MP & 3MP Outdoor Dome
17
2.3 Connection
2.3.1 Default IP address
Since this is a network-based unit, an IP address must be assigned at the very first. The unit’s default IP
address is 192.168.1.168 and sub mask is 255.255.255.0. However, if you have a DHCP server in your
network, the unit would obtain an IP address automatically from the DHCP server so that you don’t need to
change the camera’s IP address. But be sure to enable DHCP in “Network/Basic setting”
2.3.2 Connecting from a computer & Viewing Preparation
2.3.2.1 Connecting from a computer
1. Make sure the unit and your computer are in the same subnet.
2. Check whether if the networking available between the unit and the computer by executing ping the
default IP address. To do this, simply start a command prompt (Windows: from the Start Menu, select
Program. Then select Accessories and choose Command Prompt.), and type “Ping 192.168.1.168”. If
the message “Reply from…” appears, it means the connection is available.
3. Start Internet Explorer and enter IP address: 192.168.1.168. A login window should pop up. In the
window, enter the default user name: admin and password: admin to log in.
FIGURE 2-10:LOGIN WINDOW

Illustra Flex 1MP & 3MP Outdoor Dome
18
2.3.2.2 Viewing Preparation
Images of the unit can be viewed through Microsoft Internet Explorer 8 or above. Before viewing, follow these
steps to enable the display.
1. Enable Cookies as instructions below
In Internet Explorer, click Internet Options on the Tools menu.
On the Privacy tab, move the settings slider to Low or Accept All Cookies.
Click OK.
2. When a proxy server is used, click Internet Options on the Tools menus of Internet Explorer, select
Connect tab, click LAN button, and set proxy server.
3. Change Security in Internet options as instructions below
On Toolsmenu, click Internet Options.
Press the Security tab.
If the camera operates inside of the intranet, click the Intranet icon.
If the camera operates outside of the intranet, click the Internet icon.
Click Custom Level. This will open the Security Settings – Internet Zone screen.
FIGURE 2-11:SECURITY SETTINGS 1/4

Illustra Flex 1MP & 3MP Outdoor Dome
19
Scroll down to the ActiveX controls and plug-ins radio buttons and set as follows:
【
Download signed ActiveX controls
】
Prompt (recommended)
【
Download unsigned ActiveX controls
】
Prompt
【
Initialize and script ActiveX not marked as safe for scripting
】
Prompt
FIGURE 2-12: SECURITY SETTINGS 2/4
【
Automatic prompting for ActiveX controls
】
Enable
FIGURE 2-13: SECURITY SETTINGS 3/4

Illustra Flex 1MP & 3MP Outdoor Dome
20
【
Run ActiveX controls and plug-ins
】
Enable
【
Script ActiveX controls marked safe for scripting*
】
Enable
FIGURE 2-14: SECURITY SETTINGS 4/4
Press OK to save the settings.
Close all Microsoft Internet Explorer Windows and restart a new window. This will allow the new
settings taking effect.
Type your setting IP address into the browser.
Then you should be able to see the camera image screen.
2.4 Using the illustra Connect Tool to Manage Cameras
In addition to using the IE browser to access your camera, you can alternatively use the provided tool, illustra
Connect.
illustra Connect is a management tool designed to manage your network cameras on the LAN. It can:
help you find multiple network cameras
set the IP addresses
show connection status
manage firmware upgrades
For further information on Illustra Connect, refer to the Illustra Connect User Guide, located on the CD
supplied.