American Standard ACRYLUX 6032Y1.102 Operating and safety instructions

H129
© 2008 AS America Inc.
ACRYLUX™ 60" x 32" w/INTEGRAL APRON
WHIRLPOOL AND BATHING POOL
HIGH GLOSS
ACRYLUX 60" x 32" w/INTEGRAL APRON
❑ 6032Y1.102 Bathing Pool, Right Drain
❑ 6032Y1.202 Bathing Pool, Left Drain
Product Features:
• High-gloss acrylic-capped ABS with
berglass reinforcement
• Integral apron
• Integral three-sided, tiling/water retention ange
• Integral lumbar support
• Pre-leveled tub bottom
❑ 6032Y1.118 Whirlpool, Right Drain
❑ 6032Y1.218 Whirlpool, Left Drain
Whirlpool Features:
• 1.25 hp, single-speed pump motor
• 8 whirlpool jets
– 4 adjustable jets
– 4 mini-jets in the lumbar and foot areas
• Deck mounted air on/off switch
• Removable access panel
Nominal Dimensions:
59-7/8" x 32" x 18"
(1521 x 813 x 457mm)
For use with:
• 6032Y1.BW Bath Wall Set
• 6032Y1.BWT Bath Tile Wall Set
• Tub can also be installed without
Acrylux wall set
Compliance Certications -
Meets or Exceeds the Following Specications:
• UL 1795 for Hydromassage Bathtubs
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
6032Y1.102
6032Y1.118
Revised 5/08

H130
© 2008 AS America Inc.
ACRYLUX™ 60" x 32" w/INTEGRAL APRON
WHIRLPOOL AND BATHING POOL
HIGH GLOSS
GENERAL SPECIFICATIONS FOR 6032Y1 WHIRLPOOL
60 x 32 x 18 In. (1524 x 813 x 457mm)
76 Lbs. (34 Kg.)
526 Lbs. (239 Kg.)
54 Gal. (204 L)
28 Gal. (106 L)
3 In. L (76mm L)
54 In. L (1372mm L)
14 in (356mm L)
39 Lbs./Sq.Ft. (193 Kgs./Sq.m)
7.3
23.321ft3
1.25 HP, 9.7 AMPS ,120V.WHIRLPOOL PUMP
WHIRLPOOL ELECTRICAL SPECIFICATIONS
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
GENERAL SPECIFICATIONS FOR 6032Y1 BATHING POOL
60 x 32 x 18 In. (1524 x 813 x 457mm)
54 Lbs. (24 Kg.)
495 Lbs. (225 Kg.)
53 Gal. (201 L)
3 In. L (76mm L)
54 In. L (1372mm L)
14 in (356mm L)
37 Lbs./Sq.Ft. (181 Kgs./Sq.m)
7.3
23.321ft3
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA TYPE INSTALLATION. SUMP
OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIALS BY OTHERS.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
● FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
● IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING
SYSTEM PIPING AND DRAIN OVERFLOW. MOUNTING HOLES DRILLED BY INSTALLER.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1.
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaet.
10"
STUD LAYOUT
33-1/2"
(851mm)
60"
(800mm)
(254mm)
10"
6" (154mm)
15" (381mm)
8"
(203mm)
Drain C
Floor Cut Out
6"x 10"(154 x 254mm)
= Stud Location
L
59-7/8"
(1521mm)
18"
(457mm)
32"
(813mm)
Revised 5/08