American Standard Colony Corner 1730.002 User manual

H71
© 2008 AS America Inc.
COLONY CORNER™
WHIRLPOOL AND BATHING POOL
HIGH GLOSS
Revised 2/08
COLONY CORNER™ WHIRLPOOL AND
BATHING POOL
❏ 1730.018 Whirlpool featuring System I
• Acrylic with berglass reinforcement
• Molded-in seat
• Center drain outlet
• 1.25 HP single speed, self-draining pump/motor
• Factory installed power cord with plug
• Six multi-directional and ow-adjustable jets
• Deck-mounted air switch On/Off
• Two air volume controls
• Factory installed and tested whirlpool system
❏ 1730.018C EverClean® Whirlpool
Featuring System I:
• Same as 1730.018 except with the
EverClean System
❏ 1730.002 Bathing Pool only
Nominal Dimensions:
1524 x 1524 x 495mm
(60" x 60" x 19-1/2")
Compliance Certications -
Meets or Exceeds the Following Specications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
American Standard whirlpools and air baths with
EverClean® incorporate a patented silver-ion
additive right into the circulation piping to protect
the pipes from mold, mildew, algae and fungus that
could cause deterioration or staining of the pipes.
SEE REVERSE FOR PRODUCT DIMENSIONS
AND SPECIFICATIONS
To Be Specied - Required:
❏ Color:
❏ Bath Filler: (specify nish)
❏ Bath Drain: 1583.470 (specify nish)
To Be Specied - Optional:
❏ Corner Apron: 0730.121 (specify color)
❏ Jet Trim Ring Kit: 9860.200-two per kit (specify nish)
❏ Universal Tile Bead Kit: 751755-100
For color/nish availability and other faucet choices, please
see the Product Selector and Pricing Guide.

H72
© 2008 AS America Inc.
COLONY CORNER™
WHIRLPOOL AND BATHING POOL
HIGH GLOSS
495mm
(19-1/2)
117mm
(4-5/8)
C/L OF DRAIN
OUTLET
51mm
(2)
1546mm
(60-7/8)
ALT.
PUMP
1064mm
(41-7/8)
686mm
(27)
318mm
(12-1/2)
1168mm
)(46
1514mm
(59-5/8)
TOP OF
DECK
445mm
(17-1/2)
70mm
(2-3/4)
ROUGH
FLOOR
83mm
(3-1/4)
BATH SUPPORT
MATERIAL
38mm (1-1/2)
O.D. TAILPIECE
PUMP
PROVIDE ACCESS
FOR SERVICING
PUMP & CONTROLS
(6) JETS
ON/OFF
SWITCH
2 AIR
VALVES
LEVELING
STRINGER
NOT FOR
SUPPORT
483mm
(19)
2134mm
)(84
*
BATH SUPPORT
MATERIAL
495mm
(19-1/2)
6.3mm (1/4) INTEGRAL
TILE FLANGE (2 SIDES)
19mm ( )3/4
C/L OF DRAIN
OUTLET
LEVELING STRINGER
NOT FOR SUPPORT
457mm
)(18
38mm
(1-1/2)
1549mm
)(61
1064mm
( )41-29/32
686mm
)(27 686mm
)(27
1168mm
)(46
1511mm
(59-1/2)
876mm
(34-1/2) 876mm
(34-1/2)
TOP OF
DECK
56mm
)(2-7/32
ROUGH
FLOOR
79mm ( )3-1/8
101x101mm
4 x 4” FEET 38mm (1-1/2) O.D. TAILPIECE
60 x 60 x 19-1/2 In.(1524 x 1524 x 495mm)
115 Lbs. (52 Kg.)
908 Lbs. (412 Kg.)
95 Gal. (360 L.)
65 Gal. (246 L.)
30 x 50 In. (762 x 1270mm)
45-1/2 x 63-1/2 In.(1156 x 1613mm)
13 In. (330 mm)
36 Lbs./Sq. Ft. (177 Kgs/Sq. m.)
27.8
54
GENERAL SPECIFICATIONS FOR 1730 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
1.25 HP, 9.9 AMPS, 120V.SYSTEM I PUMP
60 x 60 x 19-1/2 In.
(1524 x 1524 x 495mm)
95 Lbs. (43 Kg.)
888 Lbs. (403 Kg.)
95 Gal. (360 L)
30 x 50 In. (762 x 1270mm)
45-1/2 X 31-1/2 In. (1156 x 1613mm)
13 In. (330mm)
36 Lbs./Sq.Ft. (174 Kgs./Sq.m)
27.8
54
GENERAL SPECIFICATIONS FOR 1730 BATHING POOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUMP OF
BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
CONCEALED PIPING NOT INCLUDED.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
● IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING
SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1. These
measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
Revised 2/08