American Standard Williamsburg Elite Whirlpool 2805EC User manual

WILLIAMSBURG ELITE™5’x 42”
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
WILLIAMSBURG ELITE™5’X 42”WHIRLPOOL
Comfortable two person design with dual back
support positions
❏2805E (specify White 020, Bone 021, or
Linen 222)
•Acrylic with fiberglass reinforcement
•1.5 HP self-draining pump/motor
with dry run seal
•Six multi-directional and flow adjustable jets
including:
Two high performance Ideal-flow™Jets
Four interchangeable Flex-jets™
•Two silent air volume controls
•Deck-mounted On/Off control
•Complete factory installed and tested
whirlpool system
❏2805EC (specify White 020, Bone 021, or
Linen 222)
•Same as above with the StayClean™
whirlpool system featuring Antimicrobial
AlphaSan®
Nominal Dimensions: 60”x 42”x 21-1/2"
(1524 x 1067 x 546mm)
© 2003 American Standard Inc. HD-012
SPS 2805E
Revised 6/03
Compliance Certifications -
Meets or Exceeds the Following Specifications:
•Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
•ASME A112.19.7M for Whirlpool Appliances
•ANSI Z124.1 for Plastic Bathtubs
•ASTM E162 for Flammability
•NFPA 258 for Smoke Density
* See American Standard Faucet Selector
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
Components Needed:
❏Bath Filler*: (specify finish)
❏Bath Drain: BATH-DRAIN
(specify Chrome 002, Polished Brass 099,
or Satin 295)
Custom Accessories Available:
❏Pulse Jet Kit: PULSE-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
❏Soft Jet Kit: SOFT-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
❏Williamsburg 5-Foot Apron: WBURG5-APRON
(specify White 020, Bone 021, or Linen 222)
❏E-Z-Install™Whirlpool Heater - EZHEAT-100
❏Tile Bead Kit: TILE-BEAD NOTE: E-Z-Install™Whirlpool Heater is designed to
maintain water temperature during operation. It will not
heat cold water to desired bathing temperature.

WILLIAMSBURG ELITE™5’x 42”
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUMP OF BATH IS
SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
OPTIONAL 3- WALL TILING BEAD KIT No. TILE-BEAD AND APRON WBURG5-APRON MUST BE ORDERED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
● IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING SYSTEM PIPING, DRAIN
OVERFLOW. MOUNTING HOLES DRILLED BY INSTALLER.
SUPPLY PIPING NOT INCLUDED.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1.These
measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
1524mm
(60)
INTEGRAL
FITTING DECK
762mm
(30)
1067mm
(42)
ON/OFF
SWITCH
OUTLINE OF CUTOUT
1486mm x 1029mm
(58-1/2 x 40-1/2)
PROVIDE ACCESS
TO PUMP FOR
SERVICE ON ALL
INSTALLATIONS
C/L OF
DRAIN
178mm x 381mm
(7 x 15)
FLOOR
CUTOUT
19mm
(3/4)
PUMP
305mm
(12)
152mm
(6)
1-1/2 N.P.T.
THREADS
ROUGH
FLOOR INTEGRAL
FEET
1-1/2 O.D.
TAILPIECE
546mm
(21-1/2)
495mm
(19-1/2)
133mm
(5-1/4)
64mm
(2-1/2)
121mm
(4-3/4)
LEVELING STRINGER
NOT FOR SUPPORT
C/L OF
OVERFLOW
51mm(2) IN-LINE HEATER
REMOVABLE
BLANK
GENERAL SPECIFICATIONS FOR 2805E WHIRLPOOL
60 x 42 x 21-1/2 In. (1524 x 1067 x 546mm)
130 Lbs. (59 Kg.)
689 Lbs. (310 Kg.)
64 Gal. (243 L)
52 Gal. (197 L)
43 x 22 In. (1092 x 559mm)
55 x 35-1/2 In. (1397 x 902mm)
14 In. (356mm)
39 Lbs./Sq.Ft. (191 Kgs./Sq.m)
27.8
47.4
1.6 HP, 9.7 AMPS ,120V.PUMP
WHIRLPOOL ELECTRICAL SPECIFICATIONS
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)