American Standard Virtuoso Elite Whirlpool 7236EC User manual

VIRTUOSO ELITE™
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
VIRTUOSO ELITE™WHIRLPOOL
Comfortable two person design with dual back
support positions and factory installed grab bar
❏7236E (specify White 020, Bone 021, or
Linen 222)
•Acrylic with fiberglass reinforcement
•2.0 HP self-draining pump/motor
with dry run seal
•Ten multi-directional and flow adjustable jets
including:
Two high performance Ideal-flow™Jets
Eight interchangeable Flex-jets™
•Three silent air volume controls
•Deck-mounted On/Off control
•Complete factory installed and tested
whirlpool system
❏7236EC (specify White 020, Bone 021, or
Linen 222)
•Same as above with the StayClean™
whirlpool system featuring Antimicrobial
AlphaSan®
Nominal Dimensions:
72”x 36”x 21-1/4"
(1829 x 914 x 540mm)
© 2003 American Standard Inc. HD-007
SPS 7236E
Revised 6/03
Compliance Certifications -
Meets or Exceeds the Following Specifications:
•Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
•ASME A112.19.7M for Whirlpool Appliances
•ANSI Z124.1 for Plastic Bathtubs
•ASTM E162 for Flammability
•NFPA 258 for Smoke Density
Components Needed:
❏Bath Filler*: (specify finish)
❏Bath Drain: BATH-DRAIN
(specify Chrome 002, Polished Brass 099,
or Satin 295)
Custom Accessories Available:
❏Pulse Jet Kit: PULSE-JET (two per kit,
specify White 020, Bone 021, or Linen 222)
❏Soft Jet Kit: SOFT-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
❏Six Foot Apron: 6FT-APRON (specify White
020, Bone 021, or Linen 222)
❏E-Z-Install™Whirlpool Heater - EZHEAT-100
❏Tile Bead Kit: TILE-BEAD
* See American Standard Faucet Selector
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
NOTE: E-Z-Install™Whirlpool Heater is designed to
maintain water temperature during operation. It will not
heat cold water to desired bathing temperature.

VIRTUOSO ELITE™
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
●
■
NOTES: BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR
PENINSULA TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO
ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL, DECK MOUNTED SPOUT
AND INTEGRATED BATH FILLER FOR ADDITIONAL INFORMATION.
OPTIONAL 3-WALL TILING BEAD KIT No. TILE-BEAD AND APRON No. 6FT-APRON MUST BE
ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR
INTERFERENCE WITH CIRCULATING SYSTEM PIPING, DRAIN OVERFLOW, AND APRON
INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established
by ANSI Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided leaflet.
1829mm
(72)
914mm
(36)
914mm
(36)
279mm
(11)
102mm
(4) 470mm
(18-1/2)
19mm
(3/4)
TYP.
178mm X 356mm
(7 x 14) CUTOUT
OUTLINE OF CUTOUT
1791mm X 876mm
(70-1/2 X 34-1/2)
PUMP
ON/ OFF
SWITCH
C/L OF
DRAIN
51mm
(2)
489mm
(19-1/4)
ROUGH FLOOR
1-1/2 O.D.
TAILPIECE
76mm
(3)
PROVIDE ACCESS
TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
540mm
21-1/4
C/L OF
OVERFLOW IN-LINE HEATER
REMOVABLE BLANK
1-1/2 N.P.T. THREAD INTEGRAL
FEET
LEVELING
STRINGER
NOT FOR
SUPPORT
44mm
(1-3/4)
89mm
(3-1/2)
RECOMMENDED
FITTING LOCATION
64 X 279mm (2-1/2 X 11)
GENERAL SPECIFICATIONS FOR 7236E WHIRLPOOL
WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP
72 x 36 x 21-1/4 In. (1829 x 914 x 540mm)
101 Lbs. (45 Kg.)
751 Lbs. (338 Kg.)
78 Gal. (296 L)
69 Gal. (262 L)
46 x 18 In. (1168 x 457mm)
66 x 30-1/2 In. (1676 x 775mm)
15-3/4 In.(400mm)
42 Lbs./Sq.Ft. (204 Kgs./Sq.m)
25.6
49.4
2.1 HP,14.4 AMPS,120V.
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)