American Standard Williamsburg Elite 5' Integral Apron Whirlpool... User manual

WILLIAMSBURG ELITE™5’INTEGRAL APRON
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
WILLIAMSBURG ELITE™5’INTEGRAL APRON
WHIRLPOOL
Comfortable bathing design with form-fitted
backrest and molded-in armrests
❏2425E-LHO Left Hand Drain Outlet
(specify White 020, Bone 021, or Linen 222)
❏2425E-RHO Right Hand Drain Outlet
(specify White 020, Bone 021, or Linen 222)
•Acrylic with fiberglass reinforcement
•Integral apron with removable access panel
•Integral three-sided, tiling / water retention
flange
•1.5 HP self-draining pump/motor
with dry run seal
•Eight multi-directional and flow adjustable jets
including:
Two high performance Ideal-flow™Jets
Six interchangeable Flex-jets™
•Two silent air volume controls
•Deck-mounted On/Off control
•Complete factory installed and tested
whirlpool system
❏2425EC-LHO Left Hand Drain Outlet
(specify White 020, Bone 021, or Linen 222)
❏2425EC-RHO Right Hand Drain Outlet
(specify White 020, Bone 021, or Linen 222)
•Same as above with the StayClean™
whirlpool system featuring Antimicrobial
AlphaSan®
Nominal Dimensions:
60”x 32”x 21-1/2”
(1524 x 813 x 546mm)
© 2003 American Standard Inc. HD-016
SPS 2425E-LHO/RHO
Revised 6/03
Compliance Certifications -
Meets or Exceeds the Following Specifications:
•Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
•ASME A112.19.7M for Whirlpool Appliances
•ANSI Z124.1 for Plastic Bathtubs
•ASTM E162 for Flammability
•NFPA 258 for Smoke Density
* See American Standard Faucet Selector
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
Components Needed:
❏Bath Filler*: (specify finish)
❏Bath Drain: BATH-DRAIN
(specify Chrome 002, Polished Brass 099,
or Satin 295)
Custom Accessories Available:
❏Pulse Jet Kit: PULSE-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
❏Soft Jet Kit: SOFT-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
❏E-Z-Install™Whirlpool Heater - EZHEAT-100
NOTE: E-Z-Install™Whirlpool Heater is designed to
maintain water temperature during operation. It will not
heat cold water to desired bathing temperature.

WILLIAMSBURG ELITE™5’INTEGRAL APRON
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE
INSTALLATION. SUPPORT OF BATH BY SUMP BEDDING. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or
voided leaflet.
21-1/4
(540mm)
REF.
DIM
1" WATER
RETENTION
FLANGE
(3 SIDES)
21-1/2
(546mm)
1-1/2 O.D.TAILPIECE
BATH
SUPPORT
MATERIAL
LEVELING STRINGER
NOT FOR SUPPORT
ROUGH
FLOOR
FINISHED
WALL
TOP OF
DECK
60
(1524mm)
32
(813mm)
WATER
RETENTION
FLANGE
(3 SIDES)
10-1/4
(260mm)
12
(305mm)
3
(76mm)
(8) JETS
3-1/2
(89mm)
CUTOUT IN FLOOR FOR DRAIN
PUMP
FINISHED
WALL
12
(305mm)
OPT.
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
65 & 78
(1651 & 1981mm)
C/L OF
OVERFLOW 4
(102 mm)
C/L OF
SPOUT
TILING
FLANGE
C/L OF
VALVES
C/L OF
SHOWER ARM
2-3/4
(70mm) 4-5/8
(117mm)
1-1/2 N.P.T.M.
THREADS
3/4
(19mm)
9
(229 mm)
C/L OF
SUPPLIES
C/L OF DRAIN
SEE FITTING
SPECS FOR
DIMENSIONS
(2) AIR VALVES
ON/OFF
SWITCH
ACCESS TO PUMP/MOTOR
THROUGH REMOVABLE
FRONT ACCESS PANEL
UNDERSIDE
OF DECK
16
(406mm)
IN-LINE HEATER
REMOVABLE
BLANK
GENERAL SPECIFICATIONS FOR 2425E WHIRLPOOL
WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP 1.6 HP, 9.7 AMPS,120V.
60 x 32 x 21-1/2 (1524 x 813 x 546mm)
115 Lbs. (52 Kg.)
574 Lbs. (258 Kg.)
55 Gal. (208 L.)
45 Gal. (171 L.)
16-1/4 x 38-1/4 (413 x 972mm)
26-1/4 x 52-1/2 (667 x 1334mm)
15 (381mm)
43 Lbs./Sq.Ft. (208 Kgs./Sq.m)
20.8
35.3
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)