American Standard 3052OD.0 Series Quick start guide

1754818-100 Rev. A
THANK YOU...
for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The
combination tub version is completely assembled with pump, motor, and system piping. All you need to finish
the combination tub installation are your selected fittings and electrical connections.
To ensure maximum performance and pleasure from this product, please follow the instructions and cautions.
©
AS Americas Inc. 2014
All product names listed herein are trademarks of AS Americas Inc. unless otherwise noted.
WALK-IN BATH
INSTALLATION INSTRUCTIONS
AND OWNER’S MANUAL
MODEL NUMBERS:
3052OD.X0X
C3052OD.X0X
3052D.XXX
C3052D.XXX
3252OD.X0X
C3252OD.X0X
SSXOD5230
SSXOD5230C
SSXOD5232
SSXOD5232C
ST5230D
ST5232DC

2
754818-100 Rev. A
You are now the owner of a walk-in bathtub from the most trusted name in plumbing.
We thank you for your purchase. Your American Standard®walk-in bath is a true
investment in your health and peace of mind.
Customer Support: [phone]
CONGRATULATIONS!

754818-100 Rev. A
3
OWNER’S MANUAL
TABLE OF CONTENTS:
UNPACKING THE UNIT...................................................................................... Page 4
RESPONSIBILITIES OF THE INSTALLER ......................................................... Page 5
TESTING YOUR TUB BEFORE INSTALLATION................................................. Page 6
INSTALLATION PREPARATION.......................................................................... Page 7
ELECTRICAL INSTALLATION............................................................................. Page 8
INSTALLATION PROCEDURES..................................................................... Page 9-17
SAFETY INSTRUCTIONS..................................................................................Page 18
OPERATING INSTRUCTIONS..................................................................... Page 19-20
CLEANING & MAINTENANCE.......................................................................... Page 21
WARRANTY...................................................................................................... Page 22
TROUBLESHOOTING.................................................................................. Page 23-25

4
754818-100 Rev. A
OWNER’S MANUAL
1. FIRST, inspect the carton for damage: CAREFULLY DOCUMENT AND PHOTOGRAGH ALL PERCEIVED
DAMAGE. Report all damage claims to customer service at 1-866-423-0800.
2. DO NOT LIFT THE TUB BY THE PLUMBING. Doing so can result in leaks, for which the installer is
responsible. All Walk-In Tubs are water tested before they leave our factory and the bathtub you have
purchased has passed inspection.
3. Immediately inspect the unit for damage even if there is no carton damage. All product damage must be
reported within 72 hours of receipt from American Standard®. Once the unit is installed, surface damages will
be assumed to be installation-related if not reported prior to installation. Installers are also responsible
for damage that occurs once the unit is placed in its niche.
NOTE: Remove all packaging material except for the protective plastic. This has been placed on the tub at
the factory to eliminate abrasions from handling. Thisshould only be removed at final clean up.
4. Inspect the plumbing for any fittings that may have loosened in transit.
5. Read the following instructions completely before installing this product. If the home-owner or installer has any
questions, please call us at 1-866-423-0800.
6. You must follow all the instructions in this manual.
FAILURE TO READ AND COMPLY WITH ALL INSTRUCTIONS CAN RESULT IN PRODUCT DAMAGE
OR INJURY TO BOTH INSTALLER AND HOMEOWNER. IT WILL ALSO RESULT IN ASSUMPTION OF ALL
LIABILITY BY SAID INSTALLER.
UNPACKING THE UNIT

754818-100 Rev. A
5
OWNER’S MANUAL
The Installer must inspect and water test the product prior to installation to ensure the unit is free of defect
and /or damage. In the event of a problem, the unit must not be installed. If the packaging or product has
been damaged, please call immediately at 1-866-423-0800.
This product has been listed by INTERTEK / ETL and IAPMO / C UPC. The product has been tested and
complies with the following standards and guidelines: IAPMO /C UPC, UL-1795, ANSI Z-124.1.2,
ASME A 112.19.7, ASME A 112.19.15 & CSA B-45. The installer is responsible for compliance to
state and local codes.
This product is designed to be installed by a licensed tradesperson. Licensed plumbers and electricians
should be employed to insure proper installation. Installer assumes all liabilities for installation procedures.
Although American Standard®has taken reasonable precautions to ensure that the Quick DrainTM is suitable for
residential plumbing; it is the responsibility of the installer to insure that the plumbing is acceptable for use of
the Quick DrainTM. American Standard® does not accept responsibility for damage arising from use of the
Quick DrainTM.
Only accessories authorized by manufacturer should be used with this product.
RESPONSIBILITIES OF THE INSTALLER
INSTRUCTIONS PERTAINING TO RISK OF FIRE,
ELECTRICAL SHOCK OR INJURY TO PERSONS
SAVE THESE INSTRUCTIONS!
WARNING! ALL INSTRUCTIONS LISTED IN THIS MANUAL SHOULD BE READ AND FOLLOWED CAREFULLY.
A
LL PRECAUTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS MUST BE
UNDERSTOOD AND EXPLAINED TO OWNER.
TO REDUCE THE RISK OF INJURY, CHILDREN OR PERSONS WITH INFIRMITIES MUST NOT BE PERMITTED
TO USE THIS PRODUCT WITHOUT CLOSE AND CONTINUOUS SUPERVISION.
RESPONSIBILITIES OF THE INSTALLER

6
754818-100 Rev. A
OWNER’S MANUAL
1.
All American Standard®walk-in baths are 100% water tested at the factory and have passed inspection.
Transportation and mishandling may loosen fittings and cause leaks. It is therefore necessary to
test the
bathtub while there is access to all sides of the bath.
2.
The unit needs to be filled with water and inspected for leaks along the door as well as the whirlpool and
air systems if equipped. The inspection needs to be performed with and without the whirlpool and / or ai
r
systems operating. It is best to test the unit outside by filling with a garden hose.
a. Place the tub on a completely flat surface in an area where it may be drained after testing.
b. Using a clean rag and warm water wipe down seal to insure it is free of debris.
c. Seal the drain hole (this can be done with tape) and fill the tub to at least three inches above
the highest jet, or to the bottom of the safety bar if no jets are present.
d. Allow the water to stand in tub for 30 minutes and then inspect all plumbing and seals for leaks.
e. Using appropriately rated three-prong extension cords, all plugged in to separate outlets,
operate all electrical components (air blower, water pump, and heater if applicable) for another
30 minutes and inspect for leaks again. Inspect the unions around the pump and heater.
f. If a leak persists at a union after tightening, it may have been over-tightened or might have a
displaced O-ring. Disassemble it and make sure the O-ring was seated properly. Do the same
if a leak persists at the heater. Verify that the heater threads match the pipe threads.
g. Ensure that all jets are open and working, some jets are adjustable for both flow rate and
direction of flow. The jet water flow rate is adjusted by turning either the outside ring or the
inside nozzle clockwise or counterclockwise. Some jets are not adjustable at the jet face, but
can be adjust by the “Leg’s Only Massage”. The “Legs Only Massage” Valve is located near
the seat. (If equipped.) .
3.
If the pump/blower/lights/heater does not operate:
a. Check the breaker to ensure that power is on and make sure that any cables and / or air lines
connecting the control boxes to the switches and pumps are firmly attached. Verify the correct
electrical circuit and amps of the electrical cord.
b. Go to Trouble Shooting Guidelines. (See pages 24-26.)
c. Do not run any pumps unless the tub is filled with water to the proper level. Damage due to
dry operation of pumps is not covered under the warranty period. (See pg. 23.)
Failure to perform these tests before installation will make the installer liable for future repair costs.
TESTING YOUR WALK-IN TUB BEFORE INSTALLATION

754818-100 Rev. A
7
OWNER’S MANUAL
1.
Check the floor area where the tub is to be installed.
a. Clean area of any debris or trash.
b. Use a 5 or 6-foot level and determine if the floor is level. If the floor is not level, adjust all leveling
feet to perfectly level the tub.
Note: It is important that all leveling feet are completely touching the floor and level for
the door system to work properly.
2.
Check to ensure that the drain piping has been “roughed-in” at the proper location. See specification sheets
(installation detail) included in this manual.
3.
Ensure that the proper electrical service has been installed at the pump location. See electrical
requirements in the manual. (See page 8.)
INSTALLATION PREPARATION
Leveling
Feet

8
754818-100 Rev. A
OWNER’S MANUAL
All electrical wiring must be installed in accordance with the National Electrical Code and with all local codes.
All wiring shall be done by a qualified electrician. Run one, two or three branch circuits (as required) from the
main electrical service panel to the pump area of the framing structure to provide power to the unit.
Electrical components have specific wiring requirements. Refer to the matrix below for the electrical supply
requirements for the whirlpool bathtub and factory installed components.
Branch circuits must be rated for 110 – 120 volts. Use 12 Gauge, 3 conductor cable for the circuits. If the length
run exceeds 100 feet, check with local codes for requirements. Install moisture proof junction box(s) 6" above the
floor at the pump end of the framing for each circuit.
DO NOT INSTALL THE JUNCTION BOX(S) WHERE IT CAN BE REACHED WHILE SITTING OR STANDING
IN THE TUB OR TOUCHING THE FAUCETS.
QUICK DRAIN®, LIGHTS, WHIRLPOOL, AIR SPA, COMBO & HEATER ELECTRIAL REQUIREMENTS
This section lists the factory installed components of the Whirlpool and/or Air Spa Systems.
Note the required number of circuits and their rating for the Whirlpool & Air Spa unit you are
planning to install.
ELECTRICAL REQUIREMENTS FOR FACTORY INSTALLED COMPONENTS
ELECTRICAL INSTALLATION
Electrical Rating Electrical Rating Dedicated
Systems Circuit 1 Circuit 2 Circuit
Soaker w / Quick Drain®15 Amp GFCI
Soaker w / Light 15 Amp GFCI
Soaker w / Quick Drain®w / Light 15 Amp GFCI
Whirlpool or Air Spa 15 Amp GFCI
Whirlpool or Air Spa w / Light 15 Amp GFCI
Whirlpool or Air Spa w/ Quick Drain®15 Amp GFCI 15 Amp GFCI
Whirlpool or Air Spa w/ Light & Quick Drain®15 Amp GFCI 15 Amp GFCI
Whirlpool & Air Spa (Combo) 15 Amp GFCI 15 Amp GFCI
Whirlpool & Air Spa (Combo) w/ Light 15 Amp GFCI 15 Amp GFCI
Whirlpool & Air Spa (Combo) w/ Quick Drain®20 Amp GFCI 15 Amp GFCI
Whirlpool & Air Spa (Combo) w/ Light & Quick Drain®20 Amp GFCI 15 Amp GFCI
Whirlpool Inline Heater - Dedicated Circuit 15 Amp GFCI
All electrical connections must be carried out by a certified electrician
in accordance with local electricalrequirements and codes.

754818-100 Rev. A
OWNER’S MANUAL
9
WARNING: When installing whirlpool massage baths, air spa baths, combo baths, or Quick Drain®
equipped baths, the following precautions must be followed:
WARNING: Danger: Risk of electrical shock; connect components to separate circuits, EACH protected
by a ground fault circuit interrupter (GFCI)
WARNING: Installation must provide access for servicing the pump and motor (all American Standard®
walk-in baths come with access panels for the pump, motor and faucet).
1. Install tub waste/overflow according to instructions included with the provided kits. The Gel Coat Series
requires the installation of a door drain with check valve. The check valve and tubing must be installed
horizontal to the floor. Some installations will require the purchase of additional fittings.
2. American Standard Faucet Installation # 9FHS-CH
• Review the installation instructions packed with the faucet set.
• Mask off the tub’s deck with a protective tape.
• Locate and mark the center line of the overflow fitting
• Locate and mark 1-1/2" line either side of the tub’s center line to establish the overflow clearance.
• Follow the drill template and faucet installation instructions.
3. Other Faucet Model and / or Brand
• Review the installation instructions packed with the faucet set.
• Mask off the tub’s deck with a protective tape.
• Locate and mark the center line of the overflow fitting
• Locate and mark 1-1/2" line either side of the tub’s center line to establish the overflow clearance.
• Verify the first two component mounting clearance on either side of the waste overflow as well as
above and below the tub’s deck.
• Verify the remaining component mounting clearance on both sides of the overflow as well as above
and below the tub’s deck.
• It is recommended the hand held shower be installed on the corner closest to the wall to prevent water
from leaking off the deck and on to the floor.
4. Install the optional in-line water heater per manufacturer’s instructions.
5. Standard Walk-In Bath Installation — After framing is complete, set product in place to check fit and make
certain that the tub can be properly leveled. (Caution: If the bathtub is not resting on all leveling feet, water
will not drain properly and this may cause the door to leak). Secure tub frame to the studs using metal
straps. (Not provided.)
5a. Fire-Rated Drywall — If fire-rated drywall is specified, the finished fire-rated wall must be in place before
the tub is installed. The dimensions of the framing structure must be increased by the thickness of firerated
drywall.
INSTALLATION PROCEDURES
!
!
!

10
754818-100 Rev. A
OWNER’S MANUAL
WARNING:
Never allow the weight of the tub to be supported by wood support stringers and do not use
integral tile flange (if equipped) to screw or nail in place,
as this will result in product failure and will
void the warranty.
6.
Verify the product is completely level by checking tub deck surface and ensure all leveling feet are
touching the ground.
7.
Electrical connection is made by simply plugging each cord into the GFCI outlet.
8
.After plumbing and electrical connections have been made, the tub and door seal should be cleaned of dirt
and debris. Use warm water and a non abrasive cleaner for clean up.
9.
Installation is not complete until the bathtub has been water-tested in place and does not leak.
INSTALLATION PROCEDURES
(continued)