American Standard CAMBRIDGE 2460.XXXW SERIES User manual

INSTALLATION INSTRUCTIONS
791033-100 Rev. I © American Standard Inc. 2003
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
AMERICAST BRAND
ENGINEERED MATERIAL
CAMBRIDGE™
WHIRLPOOL/BATHING POOL
2460.XXXW SERIES
2461.XXXW SERIES
FOR AFTER-SALES SERVICE CALL 1 [phone] WEEKDAYS.
1-1/2 N.P.T. THREADS
1-1/2 O.D. TAILPIECE
441mm
(17-3/8)
70mm
(2-3/4)
117mm
(4-5/8)
ROUGH
FLOOR
102mm
(4)
451mm
(17-3/4)
24mm
(15/16)
406mm
(16)
OPTIONAL
TO FLOOR
USUALLY
BETWEEN
1651 & 1981mm
(65 & 78)
711mm
(28)
C/L OF CURTAIN ROD
USUALLY 1930mm(76) FROM
FINISHED FLOOR
C/L OF
VALVES
102mm
(4)
102mm
(4)
SPOUT-
1/2 N.P.T.
FINISHED
WALL
SHOWER ARM- 1/2 N.P.T.
32mm(1-1/4) DIA. HOLE
SEE
NOTE
■
76mm
(3)
813mm
(32)
1524mm
(60)
19mm
(3/4) 70mm
(2-3/4)
203mm
(8) FINISHED
WALL
102mm
(4)
102mm
(4)
C/L OF 1/2
SUPPLIES
AS REQ'D C/L OF
DRAIN
229mm x 305mm
(9 x 12)
FLOOR
CUTOUT
PUMP
406mm
(16)
PROVIDE ACCESS TO PUMP FOR SERVICING ON ALL INSTALLATIONS
ON / OFF
SWITCH
64mm
(2-1/2)
25mm
(1)
(2) 54mm(2-1/8)
DIA. HOLES
60mm 13mm
+
(2-3/8) (1/2)
+
GENERAL SPECIFICATIONS FOR 2460/2461 WHIRLPOOL
WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM I PUMP
SAFETY HEATER 1.6 HP, 9.7 AMPS,120V.
12 AMPS, 120V.
60 x 32 x 17-3/4 In. (1524 x 813 x 451mm)
190 Lbs. (86 Kg.)
607 Lbs. (273 Kg.)
50 Gal. (190 L)
39 Gal. (148 L)
41 x 20 In. (1041 x 508mm)
54 x 26 In. (1372 x 660mm)
14 In. (356mm)
46 Lbs./Sq.Ft. (220 Kgs./Sq.m)
15.6
31.5
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
THANK YOU...
for selecting an American Standard bath. Your new
bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump,
motor, and system piping. All you need to finish the
installation are your selected fittings and electrical
connections for a whirlpool.
To insure maximum performance and pleasure from
this product, please follow the instructions and
cautions.
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor
immediately.
After inspection and during installation, protect the bath from construction damage. After installation, and before
enclosing with wallboard, tile, etc., water test the unit and check for leaks.
Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect
the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump,
motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and
enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead
(required for recess installations).
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.
WARNING! Do not lift whirlpool by the piping harness at any time.
List of Optional Components (not included):
• Safe-T-Heater 9075.120*
* see your American Standard Distributor
List of Required Components (not included):
• Drain 1583.470*
• Bath Filler*
* see your American Standard Distributor
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 4
Stringers
• Drop Cloth
• 15 amp GFCI
Outlet
• Cement, Plaster,
Grout
SAFE-T-HEATER
REMOVABLE BLANK

TYPICAL RECESS INSTALLATION
610 mm
(24)
305mm
(12)
441mm
(17-3/8)
1527mm
(60-1/8) 229 X 305mm
(9 X 12) FLOOR
CUTOUT
813mm
(32)
TUB WIDTH
791033-100 Rev. I (2)
FRAMING AND INSTALLATION
BATH MAY ONLY BE INSTALLED ABOVE THE FLOOR LINE IN A RECESS TYPE INSTALLATION, AS SHOWN IN RECESS INSTALLATION DIAGRAM.
LOCATE STUDS AS REQUIRED. INSURE ROUGH DIMENSIONS ARE PROPER, PLUMB AND SQUARE. FOR WHIRLPOOLS, PROVISION MUST
BE MADE IN ALL INSTALLATIONS FOR AN ACCESS OPENING FOR SERVICING PUMP AND CONTROLS.
THE FOLLOWING PROCEDURE MUST BE USED FOR ALL INSTALLATIONS: LEVELING SUPPORT STRINGER SHOULD BE AS INDICATED.
THE BATH IS SUPPORTED FROM THE APRON AND THE REAR TILING FLANGE. NO SUPPORT UNDER THE SUMP IS NECESSARY.
POSITION BATHTUB/WHIRLPOOL WITHIN THE RECESS, CHECK LEVEL, FRONT TO BACK, SIDE TO SIDE, AND SHIM AS NECESSARY. ALSO
CHECK DRAIN CLEARANCE HOLE IN THE SUBFLOOR.
TO SECURE THE TUB TO WOOD STUDS USE ROOFING NAILS IMMEDIATELY ABOVE THE FLANGE OF THE TUB.
TO SECURE THE TUB TO STEEL STUDS USE DRYWALL SCREWS AND FLATWASHERS.
CAUTION: TAKE EXTRA CARE WHEN DRIVING NAILS OR SCREWS TO AVOID DAMAGING THE TUB.
THE TILE OR SIMILAR FINISHED FLOOR WILL BE BUTTED AGAINST THE BOTTOM OF THE TUB APRON, ALSO HOLDING THE TUB IN PLACE.
SUGGESTED WHIRLPOOL/BATH INSTALLATION METHOD
SECURE THE BATH TO THE STUDS
AS SHOWN FOR WOOD OR STEEL STUD
CONSTRUCTION.
STUD
SHIM
DRY WALL
TILE
SEALANT
TUB
ROOFING NAIL
51 x 102mm (2 x 4) WOOD
STRINGER FULL LENGTH
51 x 102mm (2 x 4) WOOD
STRINGER FULL LENGTH
STEEL
STUD
SHIM
DRY WALL WASHER
TILE
SEALANT
TUB
4" (102mm)
DRYWALL
SCREW
WOOD STUDS
STEEL STUDS
WHIRLPOOL ONLY:
UNLESS AN ACCESS OPENING OF AT LEAST
12" X 24" (305 X 610MM) IS PROVIDED,
WARRANTY SERVICE WILL NOT BE PERFORMED.

791033-100 Rev. I (3)
ELECTRICAL DIAGRAM
READ AND FOLLOW ALL INSTRUCTIONS
BLACK
WHITE
120 VAC
GND.
SEPARATE 15 AMP
GFCI OUTLET
WHIRLPOOL MOUNTED
AIR SWITCH or
WALL TIMER
ELECTRICAL INSTALLATION
PUMP/MOTOR
ELECTRICAL INSTALLATION INSTRUCTIONS
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other
applicable codes.
WARNING:
When using electrical products, basic precautions should always be observed, including the following:
1. DANGER: RISK OF ELECTRIC SHOCK
Connect only to a circuit protected by a ground-fault circuit interrupter.
2. Grounding is required. The unit should be installed by a licensed electrician and grounded.
3. Install to permit access for servicing.
4. All building materials and wiring should be routed away from the pump body and heater (if equipped).
The whirlpool should be installed on a 120 vac, 15 amp dedicated circuit. The circuit should be hard-wired from the
electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded
neutral wire and a third wire, earth ground, are essential. ADDING THE SAFE-T-HEATER REQUIRES A SEPARATE
15 AMP MAXIMUM GFCI CIRCUIT.

791033-100 Rev. I
DRAIN CONNECTION AND SYSTEM TEST
Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the
pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of
the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings
are factory tightened and inspected, some loosening may have occured during transit.) Make sure the whirlpool is
connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the
whirlpool is running.
POST INSTALLATION CLEAN-UP
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.
Do not use wire brushes or any other metal implement on bath surface.
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or
stains may be removed using granular Spic and Span®mixed with water.
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.
HARSH CHEMICALS SHOULD NEVER BE USED ON ENAMEL SURFACES.
Abrasive cleaners must not be used since they will scratch and dull the surface. Dulled areas can be restored by rubbing
with a white automotive-type polishing compound and waxing with a liquid wax.
(4) SPIC AND SPAN®IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE
WIRE SELECTION GUIDE
Maximum distance from
fusebox to motor The sizes shown on this
chart are recommendations
for copper conductors
only. Always follow
local and national
electrical codes
Motor
Hi-Performance
Rating
50' 100'
120V Power Line
150' 200'
12 12 10 8
1.6