American Standard Evolution 7236V User manual

H95
© 2008 AS America Inc.
EVOLUTION™ 6' X 36"
WHIRLPOOL AND BATHING POOL
HIGH GLOSS
Revised 4/06
Components Required:
❏ Bath Filler*: (specify nish)
❏ Bath Drain: 1599.205.XXX (specify color)
Custom Accessories Available:
❏ Six Foot Apron: 9271.019.XXX (specify color)
❏ Safe-T-Heater Whirlpool Heater: 9075.120
❏ Tile Bead Kit: 751755-100
For color/nish availability and other faucet choices, please
see the Product Selector and Pricing Guide.
NOTE: Whirlpool Heater is designed to maintain water
temperature during operation. It will not heat cold water to
desired bathing temperature.
EVOLUTION™ 6' X 36"
Comfortable bathing design with form-tted
backrest and molded-in armrests
❏ 7236VC Whirlpool w/EverClean® System
• EverClean® System
• Acrylic with berglass reinforcement
• 2.1 HP self-draining pump/motor
• Ten ow adjustable jets including:
- Two adjustable Comfort Jets™ Hi Flo
- Eight adjustable Comfort Jets™
• Three silent air volume controls
• Side-mounted On/Off control
• Deep Soak Overow Drain for maximum
water depth
• Complete factory installed and tested
whirlpool system
• Self leveling feet
• Undermount installation option
• Quick connect whirlpool heater system
(must order whirlpool heater separately)
❏ 7236V Whirlpool
• Same as above without the EverClean® System
❏ 7236V.002 Bathing Pool
Nominal Dimensions:
72" x 36" x 21-1/4"
(1829 x 914 x 540mm)
American Standard whirlpools with EverClean®
incorporate a patented silver-ion additive right
into the circulation piping to protect the pipes
from mold, mildew, algae and fungus that could
cause deterioration or staining of the pipes.
Compliance Certications -
Meets or Exceeds the Following Specications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
AND PRODUCT SPECIFICATIONS
* See American Standard Faucet Selector

H96
© 2008 AS America Inc.
EVOLUTION™ 6' X 36"
WHIRLPOOL AND BATHING POOL
HIGH GLOSS
Revised 3/06
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA TYPE INSTALLATION. SUMP
OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.
■REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL, DECK MOUNTED SPOUT AND INTEGRATED BATH
FILLER FOR ADDITIONAL INFORMATION.
OPTIONAL 3-WALL TILING BEAD KIT No. TILE-BEAD AND APRON No. 6FT-APRON MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaet.
GENERAL SPECIFICATIONS FOR 7236V WHIRLPOOL
WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP
72 x 36 x 21-1/2 In. (1829 x 914 x 546mm)
106 Lbs. (48 Kg.)
1031 Lbs. (467 Kg.)
111 Gal. (420 L)
53 Gal. (201 L)
53-1/2 x 26-1/4 In. (1359 x 667mm)
64-1/2 x 30 In. (1638 x 762mm)
18-1/2 In.(470mm)
57 Lbs./Sq.Ft. (280 Kgs./Sq.m)
2.1 HP,14.4 AMPS,120V.
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
36"
(914mm)
21-1/2"(H)
(546mm)
20"(C)
(508mm)
20-1/8"(A)
(511mm)
DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE
OF TOLERANCES ESTABLISHED BY ANSI STANDARDS Z124.1 AND A112.19.7.
C/L OF
OVERFLOW
72"
(1829mm)
36"
(914mm)
7-3/4"
(197mm)
11"
(279mm)
3"
(76mm)
3-1/4"
(83mm)
6"
(152mm)
13-3/4"
(349mm)
CUT OUT IN FLOOR
FOR DRAIN
GENERAL SPECIFICATIONS FOR 7236V BATHING POOL
72 x 36 x 21-1/2 (1829 x 914 x 546mm)
91 Lbs. (41 Kg.)
1016 Lbs. (461 Kg.)
111 Gal. (420 L.)
53-1/2 x 26-1/4 In. (1359 x 667mm)
64-1/2 x 30 In. (1638 x 762mm)
18-1/2 (470mm)
56 Lbs./Sq.Ft. (275 Kgs./Sq.m)
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)