American Standard Cadenza Elite 6060EC Operating and safety instructions

CADENZA ELITE™ CORNER
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
CADENZA ELITE™ CORNER WHIRLPOOL
Comfortable two person design with dual back
support positions, integral seat and installed
grab bar. Includes factory installed E-Z-
Install™ Whirlpool Heater .
❏6060E (specify White 020, Bone 021, or
Linen 222)
• Acrylic with fiberglass reinforcement
• 2.0 HP self-draining pump/motor
with dry run seal
• Ten multi-directional and flow adjustable jets
including:
Two high performance Ideal-flow™ Jets
Eight interchangeable Flex-jets™
• Three silent air volume controls
• Deck-mounted On/Off control
• Complete factory installed and tested
whirlpool system
❏6060EC (specify White 020, Bone 021, or
Linen 222)
• Same as above with the StayClean™
whirlpool system featuring Antimicrobial
AlphaSan®
Nominal Dimensions:
54-1/2” x 54-1/2” x 21-1/2"
(1384 x 1384 x 546mm)
Installed Size: 76-3/4” x 65-3/8” x 21-1/2"
(1949x 1661 x 546mm)
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
© 2003 American Standard Inc. HD-001
SPS 6060E
Revised 10/03
Components Needed:
❏Bath Filler*: (specify finish)
❏Bath Drain: BATH-DRAIN
(specify Chrome 002, Polished Brass 099,
or Satin 295)
Custom Accessories Available:
❏Pulse Jet Kit: PULSE-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
❏Soft Jet Kit: SOFT-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
❏Corner Apron: CORNER-APRON (specify
White 020, Bone 021, or Linen 222)
❏Tile Bead Kit: TILE-BEAD
* See American Standard Faucet Selector
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
NOTE: E-Z-Install™ Whirlpool Heater is designed to
maintain water temperature during operation. It will not
heat cold water to desired bathing temperature.

CADENZA ELITE™ CORNER
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR
PENINSULA TYPE INSTALLATION. SUPPORT OF BATH BY INTEGRAL FEET. NO ADDITIONAL
SUPPORT REQUIRED. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL
INFORMATION.
OPTIONAL 2-WALL TILING BEAD KIT No.TILE-BEAD MUST BE ORDERED SEPARATELY.
CUTOUT TEMPLATE PROVIDED IN SHIPPING BOX. MAY BE REQUESTED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
FITTINGS NOT INCLUDED, MUST BE ORDERED SEPARATELY.
IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR
INTERFERENCE WITH CIRCULATING SYSTEM PIPING, DRAIN OVERFLOW, AND APRON
INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances
established by ANSI Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided leaflet.
NOTES:
●
●
■
▲
1949mm
(76-3/4 REF.)
546mm
(21-1/2)
ROUGH FLOOR
495mm
(19-1/2)
1384mm
(54-1/2)
1605mm
(63-3/16)
975mm
(38-3/8)
1661mm
(65-3/8)
346mm
(13-5/8)
SEAT AREA
254mm
(10) 114mm
(4-1/2)
PROVIDE ACCESS TO PUMP FOR SERVICE ON ALL INSTALLATIONS NOTE: APRON ASSEMBLY WILL PROVIDE REQUIRED ACCESS FOR SERVICING
51mm
(2)
89mm
(3-1/2)
C/L OF OVERFLOW LEVELING STRINGER
NOT FOR SUPPORT
PUMP
178mm x 381mm
(7 x 15) CUTOUT
C/L OF
DRAIN
143mm
(5-5/8)
OUTLINE OF
CUTOUT C/L
ON/OFF SWITCH
83mm
(3-1/4)
1-1/2 N.P.T. THREAD
1-1/2 O.D. TAILPIECE
38mm
(1-1/2) INTEGRAL FEET
SUPPORT
RECOMMENDED FITTING
LOCATION 64 X 381mm (2-1/2 X 15)
●
■
E-Z INSTALL WHIRLPOOL
HEATER
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
GENERAL SPECIFICATIONS FOR 6060E WHIRLPOOL
WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP
76-3/4 x 65-3/8 x 21-1/2 In. (1949 x 1661 x 546mm)
105 Lbs. (48 Kg.)
822 Lbs. (370 Kg.)
86 Gal. (326 L)
71 Gal. (269 L)
45 x 40 In. (1143 x 1016mm)
49 x 43 In. (1245 x 1092mm)
15-3/8 In. (391mm)
24 Lbs./Sq.Ft. (114 Kgs./Sq.m)
41.7
68.4
2.1 HP, 14.4 AMPS,120V.
E-Z INSTALL WHIRLPOOL HEATER 12.0 AMPS,120V.