American Standard WILLIAMSBURG ELITE 2806E User manual

WILLIAMSBURG ELITE™6 FT
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
WILLIAMSBURG ELITE™6 FT WHIRLPOOL
Comfortable oval bathing design with form-fitted
backrest and molded-in armrests
❏2806E (specify White 020, Bone 021, or
Linen 222)
•Acrylic with fiberglass reinforcement
•2.0 HP self-draining pump/motor
with dry run seal
•Six multi-directional and flow adjustable jets
including:
Two high performance Ideal-flow™Jets
Four interchangeable Flex-jets™
•Two silent air volume controls
•Deck-mounted On/Off control
•Complete factory installed and tested
whirlpool system
❏2806EC (specify White 020, Bone 021, or
Linen 222)
•Same as above with the StayClean™
whirlpool system featuring Antimicrobial
AlphaSan®
Nominal Dimensions: 72”x 36”x 21-1/2"
(1829 x 915 x 546mm)
© 2003 American Standard Inc. HD-008
SPS 2806E
Revised 6/03
Compliance Certifications -
Meets or Exceeds the Following Specifications:
•Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
•ASME A112.19.7M for Whirlpool Appliances
•ANSI Z124.1 for Plastic Bathtubs
•ASTM E162 for Flammability
•NFPA 258 for Smoke Density
Components Needed:
❏Bath Filler*: (specify finish)
❏Bath Drain: BATH-DRAIN
(specify Chrome 002, Polished Brass 099,
or Satin 295)
Custom Accessories Available:
❏Pulse Jet Kit: PULSE-JET (two per kit,
specify White 020, Bone 021, or Linen 222)
❏Soft Jet Kit: SOFT-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
❏E-Z-Install™Whirlpool Heater - EZHEAT-100
* See American Standard Faucet Selector
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
NOTE: E-Z-Install™Whirlpool Heater is designed to
maintain water temperature during operation. It will not
heat cold water to desired bathing temperature.

© 2003 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY
INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
▲ CUTOUT TEMPLATE PROVIDED IN SHIPPING BOX. MAY BE REQUESTED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
● IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING SYSTEM PIPING, DRAIN
OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.
SUPPLY PIPING NOT INCLUDED.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1.These
measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
GENERAL SPECIFICATIONS FOR 2806E WHIRLPOOL
72 x 36 x 21-1/2 In. (1829 x 914 x 546mm)
135 Lbs. (61 Kg.)
744 Lbs. (338 Kg.)
73 Gal. (276 L)
44 Gal. (167 L)
45 x 24 In. (1143 x 610mm)
60 x 30 In. (1524 x 762 mm)
14-1/2 In. (368mm)
41 Lbs./Sq.Ft. (198 Kgs./Sq.m)
25.6
49.4
2.1 HP, 14.4 AMPS ,120V.PUMP
WHIRLPOOL ELECTRICAL SPECIFICATIONS
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
914mm
(36)
457mm
(18)
279mm
(11)
INTEGRAL
FITTING DECK
ON/OFF
SWITCH
1829mm
(72)
PUMP
140mm
(5-1/2) C/L OF
DRAIN
OVERFLOW
OUTLINE OF
CUTOUT
229 x 330mm
(9 X 13)
FLOOR
CUTOUT
PROVIDE ACCESS
TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
LEVELING STRINGER
(NOT FOR SUPPORT)
1-1/2 N.P.T.M. THREADS
51mm
(2)
108mm
(4-1/4)
546mm
(21-1/2)
495mm
(19-1/2)
ROUGH
FLOOR
INTEGRAL
FEET
SUPPORT
1-1/2 O.D.TAILPIECE 51mm
(2)
108mm
(4-1/4)
IN-LINE HEATER
REMOVABLE
BLANK
C/L OF
OVERFLOW
WILLIAMSBURG ELITE™6 FT
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC