American Standard Lifetime 7236L User manual

HD-3
© 2007 American Standard Inc.
LIFETIME™ 6' X 36"
Comfortable bathing design with form-tted backrest
and molded-in armrests.
❏ Model# 7236L (specify color)
• Acrylic with berglass reinforcement
• Lifetime Overow Drain for maximum
water depth
• 2.1 HP self-draining pump/motor
• Ten ow adjustable jets including:
Two adjustable Ideal Flow Comfort Jets™
Eight adjustable Comfort Jets™
• Three silent air volume controls
• Side-mounted On/Off control
• Complete factory installed and tested
whirlpool system
• Self leveling feet
• Designed with undermount installation option
❏ Model# 7236LC (specify color)
• Same as above with the EverClean™ whirlpool
system. The EverClean™ antimicrobial system
incorporates AlphaSan®, a patented
antimicrobial agent manufactured right into the
circulation system components, which
suppresses the growth of unsightly algae,
fungus, mold and mildew.
❏ Model# 7236L.002 Bathing Pool Only
Nominal Dimensions:
72” x 36” x 21-1/4”
(1829 x 914 x 540mm)
Compliance Certications -
Meets or Exceeds the Following Specications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
AND PRODUCT SPECIFICATIONS
LIFETIME™ 6' X 36"
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
Components Required:
❏ Bath Filler*: (specify nish)
❏ Bath Drain: 1599.205.XXX (specify color)
OR 1599.500.020 (white only)
Custom Accessories Available:
❏ Six Foot Apron: 9271.019.XXX (specify color)
❏ E-Z-Install™ Whirlpool Heater - EZHEAT-100
❏ Tile Bead Kit: TILE-BEAD
Revised 7/07
For color/nish availability and other faucet choices, please
see the Product Selector and Pricing Guide.
NOTE: E-Z-Install™ Whirlpool Heater is designed to
maintain water temperature during operation. It will not heat
cold water to desired bathing temperature.
* See American Standard Faucet Selector
AlphaSan® is a registered trademark of Milliken & Co.

HD-4
© 2007 American Standard Inc.
LIFETIME™ 6' X 36"
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA TYPE INSTALLATION. SUMP OF BATH IS
SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL, DECK MOUNTED SPOUT AND INTEGRATED BATH FILLER FOR
ADDITIONAL INFORMATION.
OPTIONAL 3-WALL TILING BEAD KIT No. TILE-BEAD AND APRON No. 6FT-APRON MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING SYSTEM
PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaet.
Revised 7/07
72"
(1829mm)
36"
(914mm)
7-3/4"
(197mm)
11"
(279mm)
36"
(914mm)
3"
(76mm)
6"
(152mm)
13-3/4"
(349mm)
CUT OUT IN FLOOR
FOR DRAIN
21-1/2"(H)
(546mm)
20"(C)
(508mm)
20-1/8"(A)
(511mm)
DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE
OF TOLERANCES ESTABLISHED BY ANSI STANDARDS Z124.1 AND A112.19.7.
C/L OF
OVERFLOW
GENERAL SPECIFICATIONS FOR 7236L WHIRLPOOL
WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP
72 x 36 x 21-1/2 In. (1829 x 914 x 546mm)
106 Lbs. (48 Kg.)
1031 Lbs. (467 Kg.)
111 Gal. (420 L)
53 Gal. (201 L)
53-1/2 x 26-1/4 In. (1359 x 667mm)
64-1/2 x 30 In. (1638 x 762mm)
18-1/2 In.(470mm)
57 Lbs./Sq.Ft. (280 Kgs./Sq.m)
2.1 HP,14.4 AMPS,120V.
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)