American Standard Lakeland 33 User manual

G41
© 2008 AS America Inc.
LAKELAND™ 33" LARGE SINGLE BOWL
KITCHEN SINK
• Americast® brand engineered material
• Single bowl design
• Titanium enamel - heat resistant up to 1000°
• Acid-resisting glossy porcelain nish
• Top mount or undercounter installation
• Silicone sealant supplied
• Available in 0, 1, 3, 4 or 5 faucet
hole conguration
• Customized Hole Punching Available
(See Holes page G56)
Top Mount/Undercounter:
❏ 7193.000 No Holes
❏ 7193.001 1 Center Hole
❏ 7193.803 3 Holes
❏ 7193.804 4 Holes
❏ 7193.805 5 Holes
Undercounter Installation Order:
❏ 791123-100 Mounting Kit (consists of
cut-out templates and mounting clips)
Nominal Dimensions:
838 x 559 x 241mm
(33" x 22" x 9-1/2")
Bowl sizes:
679mm (26-3/4") wide
413mm (16-1/4") front to back
229mm (9") deep
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.4M for Americast Plumbing Fixtures
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
* See faucet section for available models
To Be Specied:
❏ Color:
❏ Faucet*:
❏ Faucet Finish:
❏ Basket Strainer: 4331.013
❏ Trap:
Optional Accessories:
❏ Basin: 8193.300.365
❏ Bottom Sink Rack: 8193.120.075
❏ Bamboo Cutting Board: 8193.200.090
❏ Dish Rack with Two Utensil Holders and
Colander Kit: 8193.400.075
❏ Under Cabinet Storage: 8193.140.075
LAKELAND™ 33"
LARGE SINGLE BOWL SINK
AMERICAST®
SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS
Revised 2/08
Shown with 4114.100 Lakeland Pull-Out
Kitchen Faucet

G42
© 2008 AS America Inc.
7193.001/803/4/5 Top Mount
7193.001/803/4/5 Undercounter Mount
NOTES:
* COUNTERTOP CUTOUT for NEW INSTALLATIONS
756mm X 527mm with 25mm Radius
(29-3/4" X 20-3/4" WITH 1" RADIUS)
* COUNTERTOP CUTOUT for REPLACEMENT INSTALLATIONS
756mm to 806mm X 527mm with 25mm Radius
(29-3/4" to 31-3/4" X 20-3/4" WITH 1" RADIUS)
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
FINISHED FLOOR
36" (914mm)
TO FINISHED
FLOOR (OPTIONAL)
COUNTERTOP
BY OTHERS
SEALING
COMPOUND
7193.804
(4 HOLES)
FINISHED WALL
OR SPLASHBACK
7193.805
(5 HOLES)
1-1/2"
(38mm)
RAD. TYP.
CUTOUT
NOTE
SPRAY
H C
*
1-1/2" O.D. TAILPIECE
1/2"
(13mm)
5-3/4"
(146mm)
9"
(229mm)
2" (51mm) OPTIONAL
33"
(838mm)
8-1/8"
(206mm)
2-1/8"
(54mm)
16-1/2"
(419mm)
8-3/8"
(213mm)
22"
(559mm)
3-1/2"
(89mm)
DIA.
1-1/2" (38mm)
DIA. HOLES TYP.
4"
(102mm)
4"
(102mm)
4"
(102mm)
4"
(102mm)
DETAIL OF MOUNTING CLIP
(KIT No.791123-100)
BRASS
INSERT 13mm
(1/2)
MIN.
REFER TO INSTRUCTIONS
PROVIDED WITH KIT FOR
ADDITIONAL INFORMATION
CLIP
MACH.
SCREW
SINK
FINISHED FLOOR
COUNTERTOP
BY OTHERS
SEALING
COMPOUND
7193.804
(4 HOLES)
FINISHED WALL
OR SPLASHBACK
7193.805
(5 HOLES)
CUTOUT
NOTE
SPRAY
*
H C
MOUNTING CLIP
(SEE DETAIL)
36" (914mm)
TO FINISHED
FLOOR (OPTIONAL)
1-1/2"
(38mm)
RAD. TYP.
1-1/2" O.D. TAILPIECE
1/2"
(13mm)
5-3/4"
(146mm)
2" (51mm) OPTIONAL
33"
(838mm)
8-1/8"
(206mm)
2-1/8"
(54mm)
16-1/2"
(419mm)
8-3/8"
(213mm)
22"
(559mm)
3-1/2"
(89mm)
DIA.
1-1/2" (38mm)
DIA. HOLES TYP.
4"
(102mm)
4"
(102mm)
4"
(102mm)
4"
(102mm)
9-1/2"
(241mm)
NOTES:
● Recommended minimum countertop thickness:
Wood - 19mm (3/4")
Marble and Solid Surface - 12mm (1/2")
* TEMPLATE PROVIDED WITH MOUNTING KIT 791123-100 FOR
UNDERCOUNTER, INSTALLATION AND COUNTERTOP CUTOUT.
FITTINGS AND UNDERCOUNTER MOUNTING KIT NOT INCLUDED
AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
LAKELAND™ 33"
LARGE SINGLE BOWL SINK
AMERICAST®
Revised 2/08