American Standard SELECTRONIC 605X.202 User manual

M965652 (11/14)
CAUTION: Use only American Standard
supplied cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any
components will void the warranty.
CAUTION: Use only American Standard
supplied cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any
components will void the warranty.
Installation Instructions
Installation Instructions
Certified to comply with ASME A112.18.1
© 2014 American Standard
NOTE TO INSTALLER: Please give this manual to the customer after installation.NOTE TO INSTALLER: Please give this manual to the customer after installation.
To l e a r n m o r e a b o u t A m e r i c a n S t a n d a rd S e l e c t r o n i c
®
Products visit our website at: www.americanstandard-us.com
or e-mail us at: [e-mail]
For Parts, Service, Warranty or other Assistance,
please call (844) CRT-TEAM / [phone] (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-306-1093)
SELECTRONIC
®
Hard-Wired AC Powered
Innsbrook Lavatory
Proximity Faucet
Product No.'s & Options
Specifications
Faucet Installation
Electrical Installation
Start-up / Maintenance
FAQ’s / Troubleshooting
Parts
1
2
2-3
4-6
7-9
9-10
11
MODEL NUMBERS
605X.202 605X.204 605X.205

1M965 6 5 2 ( 11/1 4 )
605XTMV
6059.202
6059.205
PRODUCT No.s
2
4
3
10
5
Mixing ValveBas e Produc t
All American Standard Faucets Are Water Tested At Our Factory.
Some Residual Water May Remain In The Faucet During Shipping.
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure
that your installation proceeds smoothly--please read these instructions carefully before you begin.
UNPACKING
The illustration below shows the fitting and all loose items after they have been removed from the carton.
Some items may be packaged partially assembled to other items.
1. Installation Instructions
2. Spout Assembly
3. Mounting Nuts
4. Electrical Enclosure
5. Supply Hose
6a. DC Long Life Power Pack
6b. DC Standard Battery
9
7
6d
7
6c
6b
DC Standard
Battery
6055.193
AC Plug-in
6056.193
AC Hardwire
6059.193
AC Multi
6057.193
DC Long Life
Power Pack
6053.193
6a
DO NOT REMOVE
PROTECTIVE
FILM FROM
SENSOR EYE UNTIL
INSTALLATION IS
COMPLETE.
1
6c. AC Plug-In Power Supply
6d. AC Hard-Wire Power Transfomer
7. Y-Adapter
8. 27" Extension Cable
9. 10 ft. Extension
10. Mixing Valve (optional, must be ordered separately)
888 8
8
M965652 (11/14)
CAUTION:UseonlyAmerican Standa rd
suppliedcable sets.Using non-AS supplied
cables, or cutting,splicing or modifyi ng any
components will voidthe warranty.
CAUTION:UseonlyAmerican Standa rd
suppliedcable sets.Using non-AS supplied
cables, or cutting,splicing or modifyi ng any
components will voidthe warranty.
Installation Instructions
Certifiedto comply with ASME A112.18.1
© 2014American Standard
NOTETO INSTALLER: Please give this manual tothe customer after installation.NOTETO INSTALLER: Please give this manual tothe customer after installation.
Tolearn more aboutAmerican Standard Selectronic
®
Productsvisit our website at:www.americanstandard-us.com
or e-mail us at: [e-mail]
For Parts,Service ,Warranty or other Assistance,
please call (844) CRT-TEAM/ [phone] (InCanada: 1-800-387-0369)
(InToronto Area only: 1-905-306-1093)
SELECTRONIC
®
Hard-Wired AC Powered
Innsbrook Lavatory
Proximity Faucet
Product No.'s & Options
Specifications
Faucet Installation
Electrical Installation
Start-up / Maintenance
FAQ’s/ Troubleshooting
Parts
1
2
2-3
4-6
7-9
9-10
11
MODELNUMBERS
605X.202 605X.204 605X.205

TOOLS REQUIRED; Fig. 2 Fig. 2
1Slip Joint Pliers
2Adjustable Wrench
3Plumbers' Putty or Caulking
4Phillips Screwdriver
5Flat Blade Screwdriver
6Electric Drill & 1/4" Drill Bit
7Tape Measure
12
3
4
5
6
7
10'
2
381mm
(15)
155mm
(6-1/8)
102mm
(4)
38mm
(1-1/2)
MAX.
124mm
(4-7/8)
M9656 5 2 ( 11 / 14 )
Fig. 1
114mm
(4-1/2)
500mm
(20")
3/8" COMP.
125mm
(4-7/8)
81mm
(3-3/16)
MOUNTING
SURFACE
FINISHED
WALL
Roughing-in Dimensions
175mm
(6-7/8)
162mm
(6-3/8)
35mm
(1-3/8)
DIA.
3 HOLES
108mm
(4-1/4)
57mm
(2-1/4)
Fig. 1a
1
6
5
2
4
3
6
5
5
Fig. 1b
3
SENSOR
CABLES
GENERAL DESCRIPTION:
Electronic faucet with proximity operation. Vandal resistant
solid brass construction single post mounting. Operates on
DC (battery/power pack) or AC permanent power
(plug-in/hardwire). In-line strainer for solenoid is integral.
Single inlet 3/8 compression, built-in check valves, and
flexible stainless steel 16-1/4" reach inlet hose for spout
connection.
Note: All plumbing and electrical wiring must be
installed in accordance with applicable codes,
regulations and standards.
CAUTION:Use only American Standard
supplied cable sets. Using non-AS supplied
cables, or cutting, splicing or modifyingany
components will void the warranty.
RECOMENDED ELECTRICAL BOX OR
EQUIVALENT BY OTHERS
HARD-WIRED AND MULTI AC 10’ MAX. CABLE LENGTH
4"(102mm) SQ. X 3-1/2"(89mm) DEEP ELECTRICAL BOX
Hubbel-RACO #256 OR EQUAL (BY OTHERS).
INSTALL SPOUT ASSEMBLY;
Fig. 1
INSTALLATION
1
CAUTION
Turn off hot and cold water supplies before beginning
1. Make sure PUTTY PLATE (1) is installed on
FAUCET BODY (2). Fig. 1a.
2.
Connect the two 27 " EXTENSION CABLES (3) to the
Faucet Sensor Cables.
3. Insert 27" EXTENSION CABLES (3), FLEX HOSE
(4) and STUDS (5) through holes of mounting surface.
Fig. 1a.
4. From underside of mounting surface, install SPIN
NUTS (6) onto MOUNTING STUDS (5). Fig. 1b.
5. Align FAUCET (2) and hand tighten SPIN NUTS (6)
to secure faucet to mounting surface. Fig. 1b.

3M965652 (11/14)
Fig. 2
14"
(356mm)
3-3/4"
(96mm)
2-3/4"
(71mm)
3"
(76mm)
21"
(mm)
2
4
3
1
1
1
20"
(500mm)
MOUNTING HOLES
SUPPLIES
WASTE
ENCLOSURE
MOUNTING
HOLES
LAVATORY RIM OR
MOUNTING SURFACE
NOTE: If using Mixing Valve (optional) See Sheet
#M968808 for installation instructions.
Fig. 3 1
2
1
3
3
Fig. 4
2
COLD WATER OR
TEMPERED
WALL SUPPLY
Fig. 4a
4
1. Determine location of ENCLOSURE (1). It must be
located with-in the 14" (356mm) by 21" (533mm)
shaded area shown in Figure 2 in order for electrical
connections from the spout assembly to be made.
NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance
between wall supply and ENCLOSURE (1) must be
taken into consideration.
2. Remove 4 screws from ENCLOSURE COVER (2)
and pull off COVER (2). Hold the ENCLOSURE (1)
in desired location and mark the four mounting hole
locations as shown.
NOTE: For AC installation, make power supply
connection before mounting ENCLOSURE (1) to wall.
3. It is recommended that the ENCLOSURE (1) be secured
to a wall stud or cross brace within the wall using the
SCREWS (3) supplied. If the ENCLOSURE (1) is to be
installed on tile or plaster walls, the ANCHORS (4) and
SCREWS (3) should be used.
MOUNT ENCLOSURE; Fig. 2
2
1. Connect SUPPLY NUT (1) from spout hose to nipple on
top of ENCLOSURE (2). Tighten with adjustable wrench
to make a water tight connection. Fig. 3.
NOTE; If using the optional Mixing Valve See Sheet
#M968808 for installation instructions.
CONNECT SPOUT HOSE TO
ENCLOSURE; Fig. 3
CONNECT WATER SUPPLY TO
ENCLOSURE AND WALL SUPPLY;
Fig. 4, 4a
3
4
1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on
ENCLOSURE (2).
2. Connect FLEXIBLE SUPPLY HOSE (3) to SUPPLY
NUT (1) on ENCLOSURE (2). Tighten to make a
water tight connection. Use two wrenches to tighten
if necessary. Fig. 4.
3. Connect FLEXIBLE SUPPLY HOSE (3) directly to wall
supply. Connection on FLEXIBLE SUPPLY HOSE (3)
is 3/8" compression. Use adjustable wrench to
tighten connection. Do not over tighten. Fig. 4a.
Note: FLEXIBLE SUPPLY HOSE (3) measures 20" from the
bottom of the ENCLOSURE (2) base. If additional supply
length is required, installer must purchase parts separately.
Important: If FLEXIBLE SUPPLY HOSE (3) is too long,
loop to avoid kinking.

4M9656 5 2 ( 11 / 14 )
1. Remove ENCLOSURE COVER (1). Fig. 1.
2. Feed the 27" EXTENSION CABLES (2) through the
top of ENCLOSURE (3). Fig. 1a.
FOR STANDARD BATTERY VERSION ONLY
3. Insert BATTERY (4) into BATTERY HOLDER (5),
make sure the shape of the BATTERY (4) follows the
shape of the BATTERY HOLDER (5) and terminal
end is inserted first. Fig. 1b.
4. Insert the BATTERY CONNECTOR (5a) from the
Standard Battery or Long Life Power Pack through
side GROMMET (6) as shown. Fig. 1c.
5. Connect SOLENOID CABLE (7) and BATTERY
CONNECTOR (5a) to 27" EXTENSION CABLES (2).
Place Standard Battery or Long Life Power Pack into
housing. Fig. 1d.
6. Replace ENCLOSURE COVER (1). Tighten cover
screws firmly.
DC VERSIONS (LONG LIFE POWER
PACK & STANDARD BATTERY); Fig. 1
Product Page
DC Long Life Power Pack
(6053.193) 4
DC Standard Battery
(6055.193) 4
AC Plug-in
(6056.193) 5
AC Hardwire
(6059.193) 5
AC Multi Hook-up
(6057.193) 6
A
Fig. 1a Fig. 1b
Fig. 1
2
3
1
4
5
INSTALL BATTERY
CR-P2
5a
5
CAUTION:Use only American Standard supplied
cable sets. Using non-AS supplied cables, or
cutting, splicing or modifying any components will
voidthe warranty.
ELECTRICAL INSTALLATION
Fig. 1c
7
2
STANDARD
BATTERY
LONG LIFE
POWER PACK
5a
5a
6
STANDARD
BATTERY
LONG LIFE
POWER PACK
Fig. 1d 5a

M965652 (11/14)
5
CAUTION: Use only American Standard
supplied cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any
components will void the warranty.
ACVERSIONS (HARDWIRE / PLUG-IN);
Fig. 2
B
CAUTION Disconnect AC power supply before opening ENCLOSURE.
NOTE: For AC installation, make power supply connection
before mounting ENCLOSURE (3) to wall.
1. Remove ENCLOSURE COVER (1). Feed the
EXTENSION CABLES (2) from the Faucet through the
top of ENCLOSURE (3). Fig. 2.
2a. Insert POWER CORD (8) through POWER SUPPLY
GROMMET (9) Fig. 2a.
3a. Insert POWER CORD (8) through side GROMMET (6) as
shown. Fig. 2a.
4a. Connect 27" EXTENSION CABLES (2) to SOLENOID
CABLE (7) and POWER CORD (8). Fig. 2a.
5a. Mount ENCLOSURE to wall. Replace ENCLOSURE
COVER (1). Tighten cover screws firmly.
6a. Plug AC POWER SUPPLY into wall outlet.
2b. Insert one end of the 10' EXTENSION (10a) through POWER
SUPPLY GROMMET (9). Fig. 2b.
3b. Insert 10' EXTENSION (10a) through side GROMMET (6) as
shown. Fig. 2b.
4b. Connect 10' EXTENSION (10a) to single terminal of
Y-ADAPTER (11). Fig. 2b.
5b. Connect 27" EXTENSION CABLES (2) to SOLENOID CABLE (7)
and to either of the two terminals at the one end of the
Y-ADAPTER (11).
6b. Mount ENCLOSURE (3) to wall. Replace ENCLOSURE
COVER (1). Tighten cover screws firmly.
Contractor to supply ELECTRICAL BOX (12) and power to
POWER SUPPLY (13).
7b. Mount POWER SUPPLY (13) into ELECTRICAL BOX (12).
Connect White and Black connections to POWER SUPPLY
CONNECTIONS (14). Fig. 2c.
8b. Connect the10' EXTENSION (10b) to the POWER SUPPLY
CABLE (15). Fig. 2c.
Fig. 2
Fig. 2a
10a
11 7
2
2
7
Fig. 2b
2
3 1
6
6
9
9
FROM ELECTRICAL BOX
WITH POWER SUPPLY
Fig. 2c
BLACK & WHITE
POWER
CONNECTIONS
15
13 CONNECTOR NOT
USED IN THIS
INSTALLATION
10b
14
4" ELECTRICAL BOX
OR EQUIVALENT BY
OTHERS
12
FOR HARDWIRE HOOK-UP ONLY;
8
2
PLUG INTO
WALL OUTLET
FOR PLUG-IN HOOKUP ONLY

6M965652 (11/14)
MULTI-AC VERSION (DAISY-CHAIN); Fig. 3, 3a
Important: All enclosure covers must be removed before beginning to make daisy-chain connections.
Disconnect the first unit’s Y-Adapter from power supply before making daisy-chain connections.
Note: For Unit #1 electrical instructions, refer to section B (page 5).
For subsequent Units, refer to instructions below...
C
Unit #2 Detail
Unit #2 Unit #3
Fig. 3
Fig. 3a
10 ft.
EXTENSION
CABLE
AC POWER
SUPPLY
AC HARDWIRE
POWER SUPPLY
*MAXIMUM OF 15 UNITS PER
AC POWER SUPPLY.
10' MAXIMUM CABLE
LENGTH BETWEEN UNITS.
CAUTION: Use only American Standard
supplied cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any
components will void the warranty.
OR
5
5b
10b
6a
6b
10a
Unit #1
Already installed
7
2
2
11
11a
3
1. Remove COVERS from all ENCLOSURES (3).
2. Insert pervious unit’s 10' EXTENSION (11a) through
gray GROMMET (5b) and connect to single terminal of
Y-ADAPTER (11).
3. Remove solid black plug grommet from left side of all
ENCLOSURES (3), and replace with GRAY
GROMMET (5b). (Supplied with each Faucet).
4. Feed 27" EXTENSION CABLES (2) through the top of
ENCLOUSURE (3). Connect one 27" EXTENSION
CABLE (2) to the SOLENOID CABLE (7), and the other
to either of the two terminals at the one end of the
Y-ADAPTER (11). Connect the current unit’s 10'
EXTENSION (10a) to available terminal of the
Y-ADAPTER (11).
5. Feed the other end of the 10 ft.EXTENSION (10b)
through the two GRAY GROMMETS (6a and 6b) and
connect to the single terminal of the next unit’s
Y-ADAPTER (11). Place Y-ADAPTER (11) into
ENCLOSURE (3).
6. Repeat Steps above for each additional Unit, for a
Max. of 15 Units on one AC POWER SUPPLY.
7. Replace ENCLOSURE COVERS. Tighten cover screws firmly.

7M965652 (11/14)
Fig 1
5
6
4
10
3
DETECTION
ZONE
Fig. 2
1
MAINTENANCE
When the Sensor detects a user, the water immediately
starts to flow. Water flow will stop 2 seconds after user is
out of sensor range. The off delay allows the user to
comfortably move his hands without the flow cycling on
and off. As a precaution, a safety timer will turn off the
water, after the sensor has been blocked for 59 seconds.
The water will stay off until the blockage is removed from
the detection zone.
Detection Zone: 2" - 10" (50mm - 250mm)
Default: Set at Factory 6" (150mm)
HANDWASH SENSOR OPERATION;
Fig. 1
A
1. Remove cover from ENCLOSURE. Disconnect
Power Supply (1), then reconnect. Fig. 2.
2. While the SENSOR CONTROL LED (2) is blinking
slowly, place your hand 1 - 2 in. (30-50mm) in front
of the sensor. Fig. 2a.
3. When the LED stops blinking and stays "ON", move
your hand to the desired position and hold in place
until the LED begins to blink again. Fig. 2a.
4. Once the SENSOR CONTROL LED (2) begins to
blink again, remove your hand from the detection
zone. When the flashing stops, the detection
distance is set.
5. Replace ENCLOSURE COVERS (2). Tighten cover
screws firmly.
CHANGE SENSOR RANGE;
(Factory set at 6") Fig. 2, 2a
B
CLEAN FILTER ASSEMBLY; Fig. 3
C
CAUTION Before opening ENCLOSURE disconnect AC power supply.
6
WHITE
DEBRIS
CUP
FILTER
SCREEN
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Fig. 3
7/16" SOCKET
4mm HEX WRENCH
13
1. Remove ENCLOSURE COVER.
2. Close SUPPLY STOP (13) with 4mm Hex wrench.
Note: Activate sensor to keep water flowing out of
faucet while shutting off.
3. Unthread FILTER ASSEMBLY (6) using a 7/16" socket.
4. Pull out the FILTER ASSEMBLY (6), remove and clean
white debris cup and filter screen.
5. Install the FILTER ASSEMBLY (6) back in its place and
tighten with a 7/16" socket.
Caution: Do not over tighten.
6. Open SUPPLY STOP (13) with 4mm Hex wrench.
7. Replace ENCLOSURE COVER. Tighten cover
screws firmly.
Fig. 2a 1" - 2" (30mm - 50mm)
BLINKING LED
UP TO 10" (250mm)
BLINKING
LED
2
2

8M96 5 6 5 2 ( 11 / 14 )
1. Remove AERATOR HOUSING (1) with KEY supplied
with faucet.
3. Remove AERATOR (2) from HOUSING (1).
2. Clean the AERATOR SCREENS (3).
4. Clean with water. Reassemble and install into
spout end. Make sure black seal washer is in place.
CLEAN AND REMOVE
THE AERATOR; Fig. 5
E
2
3
Fig.5
1
Fig.5
INSTALL / REPLACE THE BATTERY or
LONG LIFE POWER PACK; Fig. 4
D
1. Remove COVER from ENCLOSURE (1).
2. Disconnect BATTERY HOLDER (3) from 27"
EXTENSION CABLE (5).
3. Remove old BATTERY from BATTERY HOLDER (3).
Install new BATTERY (2) making sure the terminal side
is inserted first and shape of the battery follows the shape
of the BATTERY HOLDER (3).
4. To replace LONG LIFE POWER PACK (4), unplug and
replace with new Power Pack.
5. Reconnect BATTERY HOLDER (3) to 27" EXTENSION
CABLE (5).
6. Replace ENCLOSURE COVER. Tighten cover screws firmly.
Fig. 4
CR-P2
6
3
2
STANDARD
BATTERY
LONG LIFE
POWER PACK
4
1
5

9M965652 (11/14)
CAUTION
GENERAL CLEANING; Fig. 6
1. For general cleaning use a damp, soft cloth to clean
the spout and the sensor.
2. For cleaning dirt use a soft cloth with diluted dish
washing detergent. Wipe the area using a wet cloth
and dry using a soft cloth.
Do not scratch the sensor when cleaning.
Avoid using anything that may scratch the spout
surface. Never use polishing power, detergent or a
nylon scrub brush. They will damage the surface of the
spout or Sensor.
F
Fig.6
FAQ'S
Q: How will I know if the battery needs to be replaced?
A: Valve will not open and sensor will continuously blink 2 times interrupted by a pause for up to 7 days.
Q: Why has the flow rate of the faucet reduced significantly?
A: The filter assembly, flow regulator or areator/spray may be clogged. Check and clean. Refer to Start-up/Mainenance,
sections C, D and E.
Q: Why doesn’t the water flow out of faucet when I'm within the sensor detection zone?
A: Battery may need replacement. Check. If sensor continuously blinks 2 times interrupted by pause, replace battery
or call (844) CRT-TEAM / [phone].
Q: What is the normal operating pressure range?
A: Faucet will operate with supply pressures ranging from 20-80 psi.

10 M965652 (11/14)
© American Standard Inc. 2012
TROUBLESHOOTING FLOW CHARTS
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
(844) CRT-TEAM / [phone]
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of AS America, Inc. ©2014
To learn more about American Standard Selectronic® Products visit our website at:
www.americanstandard-us.com or e-mail us at: [e-mail]
UNIT DOES NOT FUNCTION
11
22
YES
YES
YES
NO
NO
NO
YES
NO
OPEN EXTERNAL SUPPLY STOPS.
OPEN INTERNAL SUPPLY STOP.
(HEX KEY NEEDED)
CRITICALLY LOW BATTERY.
INSTALL NEW BATTERY.
DEAD BATTERY. INSTALL
NEW BATTERY. REPEAT.
NO
CHECK FOR DAMAGE TO SENSOR WIRE INSULATION.
REPLACE SENSOR.
ARE EXTERNAL SUPPLY
STOPS OPEN?
IS INTERNAL SUPPLY
STOP OPEN?
REPEATED DOUBLE FLASH
ON SENSOR?
RECONNECT BATTERY TO SENSOR.
DOES SENSOR FLASH FOR 5 SECONDS?
REPLACE SOLENOID
YES
YES
NO
CHECK FOR DAMAGE TO SENSOR WIRE INSULATION.
REPLACE SENSOR.
RECONNECT BATTERY TO SENSOR.
DOES SENSOR FLASH FOR 5 SECONDS?
NO
FULLY OPEN INTERNAL & EXTERNAL SUPPLY
STOPS BY TURNING COUNTER CLOCKWISE.
LOW FLOW COULD BE CAUSED BY DEBRIS
IN THE FILTER ASSEMBLY, FLOW REGULATOR
OR AERATOR/SPRAY. REMOVE, CLEAN AND
INSERT BACK TO ORIGINAL POSITION.
ARE INTERNAL & EXTERNAL SUPPLY
STOPS FULLY OPEN?
REPLACE SOLENOID
WATER IS CONTINUOUSLY RUNNING
LOW FLOW ISSUES