American Standard 1660 User manual

EXTENDER BODY SPRAYS
Installation
Instructions
M968617 Rev.1.2
1660.130
1660.140
1660.130 1660.140
LUXURY SHOWER
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1
ROUGHING-IN DIMENSIONS
Recommended Tools
Flat Blade Screwdriver
ALL CONNECTIONS 1/2" NPT
2-1/4" DIA.
(57mm) Hole Saw
75mm
(3")
54mm D.
(2-1/8") 35mm
(1-3/8")
57mm D.
(2-1/4")
HOLE SIZE
12mm
(1/2")
26mm
(1")
15°
FINISHED WALL 1/2" NPT
74mm D.
(2-15/16")
1660.140 Multifunction
Square Body Spray
1660.130 Multifunction
Round Body Spray
Teflon Tape Electric Drill
(63.6-70.6mm)
2-1/2" - 2-3/4"
(75.6-82.6mm)
2-15/16" - 3-1/4"

M968617 Rev.1.2
2INSTALL PLASTER GUARD
3
FINISHED WALL
REMOVE
MINIMUM
(LINE MARK)
MAX.
(LINE MARK)
2
1
INSTALL
Make sure the O-RING (3) is installed on the PLASTER GUARD (1).
Install the PLASTER GUARD (1) into ELBOW (2). Note: The finished wall must be between the Min. & Max.
lines on the PLASTER GUARD (1).
Complete all tiling and wall work. When walls are finished remove PLASTER GUARD (1).
1
CAUTION Turn off hot and cold water
supplies before beginning.
1INSTALL SUPPLY PIPING
Provide a “Installation Hole” 2-1/8" - 2-3/8" DIA., (54-60mm) and 3-1/4", (83mm) deep. Note: The “Installation Hole”
must be clear to allow body spray clearance.
Install the ELBOW (1) on a support within the wall at the *dimension shown. Secure with
two M5 SCREWS (2) (not provided).
FINISHED WALL
WALL SUPPORT
54-60mm
(2-1/8" - 2-3/8" DIA.)
1
2
83mm
(3-1/4")
54-60mm
(2-1/8" - 2-3/8" DIA.)
*63.6-70.6mm
(2-1/2" - 2-3/4")
82.6mm
(3-1/4")
*75.6-82.6mm
(2-15/16" - 3-1/4")
2
1
2
3
“Installation Hole”
“Installation Hole”
{

M968617 Rev.1.2
4INSTALL ESCUTCHEON
Align ribs on back of ESCUTCHEON (1, 2), with slots in BODY SPRAY (3). Push ESCUTCHEON (1, 2) against BODY
SPRAY (3) until ESCUTCHEON (1, 2) snaps into place.
Turn on water supply and test installed BODY SPRAY (3) for leaks and proper operation.
FINISHED WALL
6
4
1
3INSTALL BODY SPRAY
Remove the PLASTER GUARD (1) if not already removed.
Make sure the O-RING (2) and FLANGE GASKET (6) are installed on the BODY SPRAY (3). Thread BODY SPRAY (3)
into the ELBOW (4).
Tighten BODY SPRAY (3) using WRENCH (5) supplied until flush against finished wall and FLANGE GASKET (6) is
compressed. Turn on water supply and test installed BODY SPRAY (3) for leaks and proper operation.
2
2
6
3
FINISHED WALL
5
5
1
1 2
2
4
3
5CARE:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
3
ALIGNMENT RIBS ON
BACK OF ESCUTCHEON
ALIGNMENT RIBS ON
BACK OF ESCUTCHEON
SLOTS