American Standard BERWICK 7431.9 Series User manual

DECK MOUNT BATH FILLER
BERWICK™/ BOULEVARD™
Certified to comply with ANSI A112.18.1M
Installation
Instructions
7430.9XX
7431.9XX
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Recommended Tools
*Supplied with Fitting
*Hex key
SPOUT BASE RECESS
Turn off hot and cold water
supplies before beginning.
CAUTION
12
Assemble RUBBER WASHER (4) and BRASS WASHER (5) and
LOCKNUT (6) onto SPOUT SHANK (3). Align SPOUT ASSEMBLY
and from underside of ledge secure SPOUT ASSEMBLY into
position with LOCKNUT (6).
SPOUT ASSEMBLY PREPARE TUBE AND TEE ASSEMBLY
4
2
3
1
3
4
1
2
4
5
Prepare TUBE and TEE ASSEMBLY (1) to fit center to center
VALVE (2) location (between 6-1/2" and 12"). If necessary,
cut and/or bend TUBING carefully. Make sure tube bend is
close to the TEE (1) so that it will not effect the compression
joint at the VALVE CONNECTION.
ADJ. 6-1/2 TO 12
6
5
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
MOUNTING
SURFACE
VALVE inlet is 3/4-inch NPT male.
NOTE
ROUGHING-IN DIMENSIONS
MOUNTING
SURFACE
Install RING WASHER (1) into spout base recess. Check that
O-RING (2) on end of SPOUT SHANK (3) is in place. Insert SPOUT
SHANK (3) through center hole on mounting surface.
3
Remove COUPLING NUT (3) and FERRULE (4) from each
VALVE (2) and slide onto TUBING (5).
SPOUT
ASSEMBLY
70mm
(2-3/4")
152-305mm
(6"-8")
57mm
(2-1/4")
10 8 m m
(4-1/4")
52mm
(2")
17 0 m m
(6-3/4")
286mm
(11-1/4")
212mm
(8-3/8")
1-1/2 MAX.
(38mm) MAX.
1-3/16" MAX.
(30mm) MAX.
1-3/16 D.
(30mm) D.
3'
(76mm)
(H) (C)
1-1/8 D.
12 MAX.
(305mm)
1-1/16 D.
(27mm) D.
3/4-14 MALE
N.P.T. INLETS
M968644 REV.1.4 (10/16)

M968644 REV.1.4 (10/16)
2
4
5/16'' MIN. MOUNTING
SURFACE
FOR FITTING
LESS SPRAY
11
11
10
2
1
3
Push TUBING (3) ends into VALVE (4) side outlets. Insert VALVES (4)
into mounting holes from underside of ledge.
Press TEE (5) onto SPOUT SHANK (6) making certain that the O-RING (7) is
properly seated on SHANK (6). Push COUPLING (8 or 8a) into TEE (5) and
attach to SPOUT SHANK (6) and tighten. For 7430.901 use a 10 mm
(3/8") hex key.
Install LOCKNUTS (1) and RUBBER WASHERS (2) onto valve shanks.
Place RUBBER RING (10) into ESCUTCHEON ADAPTERS (9) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) to secure VALVE (4) position with channel locks.
Slide FERRULE (12) and COUPLING NUT (13) to outlet of VALVE (4) and tighten
COUPLING NUT (13) firmly.
Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
VALVE ASSEMBLY
HOT
COLD
12 13
7
6
8
8a
5
13
12
3
44
MOUNTING
SURFACE
Threads of VALVE BODY (4) should extend at least 5/16 inch above
MOUNTING SURFACE (11). If necessary, adjust LOCKNUT (1).
10
9
9
8
7
4
5
INSTALL HANDLES
1
2
4a4
5
13
LEVER HANDLE CROSS HANDLE
FLAT BLADE
SCREWDRIVER
Push ADAPTER (1) on VALVE STEM (2). Tighten
STEM SCREW (3) with a flat blade to secure ADAPTER (1).
(Figure A)
Find correct position of HANDLE ASSEMBLY (4, 4a) by adjusting
male teeth on ADAPTER (1) to female teeth in HANDLE (4, 4a).
Thread HANDLE ASSEMBLY (4, 4a) onto DECK ADAPTER (5)
until snug against mounting surface.
THREAD ON
TO DECK
ADAPTER
(Figure A)
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Thread counter-clock wise HANDLE BASE (1) to remove
HANDLE ASSEMBLY (2) from ESCUTCHEON BASE (3).
Use a flat blade screw driver to remove SPRING CLIP (4).
Lift STOP WASHER (5), turn 90˚ and replace.
Replace SPRING CLIP (4).
Reinstall HANDLE ASSEMBLY (2).
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90˚.
SERVICE
90˚
1
5
3
4
2
1

M968644 REV.1.4 (10/16)
HANDSHOWER INSTALLATION
(FOR MODEL 7430.901 ONLY)
Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max from SPOUT
center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2)
is properly seated in ESCUTCHEON (1). Install RUBBER WASHER (3) and LOCKNUT (4) from
underside of ledge.
Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT (4).
Add SEAL WASHER (5) and connect HOSE (10) to outlet nipple
at the bottom of TEE (7). Tighten firmly.
Slip SHOWER HOSE (8) with COUPLING NUT through SPRAY
HOLDER (6) and ESCUTCHEON (1). ( Note: SPRAY HOLDER (6)
must be separate from ESCUTCHEON (1) to get HOSE (8)
thrrough ESCUTCHEON (1).] Install SEAL (9) and connect both
HOSES (8) and (10). INSTALL second SEAL (9) and connect
HAND SHOWER (11) to SPRAY HOSE (8).
When not in use, HANDSHOWER should be seated
in the HOLDER.
NOTE
6
1
2
3
4
5
7
8
10
9
9
11
6
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
Hex wench
(supplied)
Before the bathroom is completely finished, you may
want to remove spout, handshower, and handles to
avoid damage during construction.
To remove handles, reverse steps in section 4.
To remove SPOUT (1), proceed as follows:
Unthread LIFT ROD KNOB (2) to release it from the
TRANSFER ROD (8). Remove LIFT ROD KNOB (2). VIEW A.
Remove PLUG BUTTON (3) and remove SET SCREW (4)
using 5mm hex wrench supplied.
Lift SPOUT (1) off SHANK (5) carefully and remove RUBBER
RING (6).
Unthread SHANK SLEEVE (7) and remove from SHANK (5).
Reverse sequence to re-install SPOUT (1). Be sure RUBBER
RING (6) is properly seated in its recess at the base of the
SPOUT (1). Make certain SET SCREW (4) is properly aligned
and tight so that SPOUT (1) is locked in place.
1
8
8
3
4
6
5
7
VIEW "A"
VIEW "A"
7MAKE WATER SUPPLY CONNECTIONS
8
7A
Connect HOT water supply to LEFT INLET UNION (1) and COLD
water supply to RIGHT INLET UNION (2). Pipe connections are
3/4" NPT. Use sealant or Teflon tape on pipe connections.
Do not solder directly to valve body.
TEST INSTALLED FAUCET
3/4" X 3/4" NPT UNION
(NOT SUPPLIED)
HOT
COLD
3/4" NPT
3/4" NPT
7
1
8
3
IMPORTANT: It is strongly recommended that access be
provided for all enclosed mechanical parts to this system.
2
FIG. 1
AERATOR
SET
SCREW
5
4
6
2
With HANDLES (3) in OFF position, turn on water
supplies and check all connections for leaks.
Remove AERATOR (4). First loosen aerator set screw
with HEX WRENCH (5) supplied. Pull out AERATOR (4)
with AERATOR KEY (6).
Operate both HANDLES (3) to flush water
lines thoroughly. Lift HAND SHOWER (7) from HOLDER,
direct spray into tub. Lift TRANSFER KNOB (8) to check
HAND SHOWER (7) and HOSES for leaks.
Turn handles "off" and replace HAND SHOWER (7).
Replace AERATOR (4) and tighten set screw.

M968644 REV.1.4 (10/16)
617852-0070A
HANDLE ADAPTER
M962849-0070A
STREAM STRAIGHTENER
M962831-YYY0A
LEFT LEVER
HANDLE ASSEMBLY
M962837-YYY0A
CROSS HANDLE
ASSEMBLY
M962832-YYY0A
RIGHT LEVER
HANDLE ASSEMBLY
028679-0070A
TUBE & TEE
ASSEMBLY
012668-0070A
SHANK KIT
030274-0070A
SHANK
MOUNTING KIT
M911810-0070A
RUBBER RING
M918378-0070A
SET SCREW
012078-0070A
VALVE COUPLING KIT
M962738-YYY0A
HAND SHOWER
HOLDER
028699-0070A
COUPLING (FOR TRANSFER)
028667-0020A
HAND SHOWER HOSE
033760-0070A
HAND SHOWER SEAL KIT
051343-0070A
HOSE KIT
030275-0070A
SHANK SLEEVE KIT
030278-0070A
TRANSFER
SEAL KIT
M962846-YYY0A
SPOUT KIT (WITH TRANSFER)
M962845-YYY0A
SPOUT KIT (LESS TRANSFER)
MODEL NUMBER
7430.9XX / 7431.9XX
028698-0070A
COUPLING
(LESS SPRAY)
M952454-0070A
TRANSFER
ROD ASSEMBLY
M962850-YYY0A
BUTTON AND SCREW
DECK-MOUNT BATH FILLER
CHROME
SATIN NICKEL
002
295
Replace the "YYY" with
appropriate finish code
1660609.YYY
HAND SHOWER
M961634-0070A
VALVE MTG. KIT
994053-0070A
CARTRIDGE
M962830-0070A
DECK ADAPTER KIT
918555-0070A
HANDLE SCREW
M962575-YYY0A
TRANSFER KNOB
BERWICK™/ BOULEVARD™
A952849-0070A
CHECK VALVE
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200 Product names listed herein are trademarks of AS America, Inc. © AS America, Inc. 2016