American Standard 6516 Top Spud Series User manual

BEFORE YOU BEGIN
SAVE FOR FUTURE USE
7302379-100 11/18
CAUTION: PRODUCT IS FRAGILE.TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
Product names listed herein are trademarks of AS America Inc.
© AS America Inc. 2018
NOTES:
• Pictures may not exactly define contour of china and components.
• Observe all local plumbing and building codes.
• Refer to local codes and manufacturer’s instructions for flush valve requirements.
• Carefully inspect the new urinal for damage.
• Fixture dimensions are nominal and conform to tolerances by ASME Standard A112.19.2.
• Site preparation may require additional tools and hardware.
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is
installed properly, please read these instructions carefully before you begin. (Certain installations may require professional
help.) Also be sure your installation conforms to local codes.
!
6516 Top Spud & 6517 Back Spud Series
6516 Top Spud 6517 Back Spud
Greenbrook Urinal
INSTALLATION INSTRUCTIONS
C/L OF OUTLET
3/4" SPUD
FINISHED
FLOOR
697 mm
(27-1/2")
102 mm
(4")
121 mm
(4/3/4")
411 mm
(16-1/8")
212 mm
(8-3/8")
420 mm
(16-1/2")
MANUAL
OVERRIDE
BUTTON SUPPLY DN 20 mm
(3/4" I.P.S.)
292 mm
(11-1/2")
108 mm to 133 mm
(4-1/4" to 5-1/4") FINSHED WALL
285 mm
(11-1/4")
380 mm
(15")
50 mm
(2")
419 mm
(16-1/2")
15
432mm (17")
MAXIMUM
610mm (24")
OPTIONAL
TO FINISHED
FLOOR
13mm
(1/2")
13mm
(1/2")
102mm
(4")
GASKET
2" N.P.T.
INSIDE THREADS
DETAIL OF OUTLET CONNECTION
FINISHED
WALL
8mm x 25 mm
(5/16" x 1") SLOT
K2 HANGERS
446 mm
(17-1/2")
C/L OF OUTLET
8mm x 25 mm
(5/16" x 1") SLOT K2 HANGERS
FINISHED
FLOOR
697 mm
(27-1/2")
102 mm
(4")
121 mm
(4/3/4")
411 mm
(16-1/8")
212 mm
(8-3/8")
420 mm
(16-1/2")
446 mm
(17-1/2")
FINSHED WALL
285 mm
(11-1/4")
380 mm
(15")
432mm (17")
MAXIMUM
610mm (24")
OPTIONAL
TO FINISHED
FLOOR
13mm
(1/2")
13mm
(1/2")
102mm
(4")
GASKET
2" N.P.T.
INSIDE THREADS
DETAIL OF OUTLET CONNECTION
FINISHED
WALL
55 mm
(2-1/8")
67 mm
(2-5/8")
RECOMMENDED TOOLS AND MATERIALS
Safety Glasses Tape Measure Adjustable Wrench Pencil Hole Cutting Equipment
Thread Sealant 1/4" Ratchet Blade Screwdriver Levels

a. Turn the water supply OFF.
b. Install or relocate the supply tubing and waste pipe as necessary to conform to the roughing in dimensions.
c. Install the shut off valve.
d. Install adequate support framing for the wall hangers as needed.
e. Determine the position of the waste pipe nipple. When establishing the nipple length, take into account the
length of the urinal outlet spud and the distance the female collar will thread onto the waste pipe nipple.
NOTE: Add a little extra length to the nipple to allow for gasket space.
PREPARATION
7302379-100 11/18
- 2 -
1
a. Install the wall hangers according to the roughing in illustration.
b. Apply thread sealant tape to the pipe threads and install the female collar to the waste pipe.
c. Place the gasket onto the female collar with the beveled surface facing away from the collar.
d. Carefully position the urinal on the wall hangers.
e. Secure the urinal to the female collar using the screws and washers provided.
INSTALL THE URINAL
2
CAUTION: RISK OF PERSONAL INJURY OR PRODUCT DAMAGE. HANDLE WITH CARE.
VITREOUS CHINA CAN BREAK OR CHIP IF THE PRODUCT IS HANDLED CARELESSLY.
!
CAUTION: RISK OF PRODUCT DAMAGE. DO NOT OVERTIGHTEN THE BOLTS.
!
a. Install the flush valve according to the manufacturer’s instructions.
b. Connect the water supply and complete the waste pipe connections.
c. Turn on the water supply.
d. Flush and check the entire installation for leaks.
NOTE: In the event of splashing, adjust the “angle stop” as needed.
COMPLETE THE INSTALLATION
3
Wash with mild soapy water and rinse thoroughly. Dry with a soft cloth. Avoid detergents, disinfectants or cleaning
products in aerosol cans as they may damage fittings.
CARE & CLEANING
Wall Hangers
Support Wall
212mm
(8-3/8")
In the United States:
American Standard Brands
1 Centennial Ave.
Piscataway, New Jersey 08854
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.americanstandard.com
In Canada:
AS Canada, ULC
5900 Avebury Rd.
Mississauga, Ontario
Canada L5R 3M3
Toll Free: [phone]
www.americanstandard.ca
In Mexico:
American Standard B&K Mexico
S. de R.L. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Toll Free: 01-800-839-1200
www.americanstandard.com.mx
Installed Wall
Hangers
Female Collar
Gasket
Screw
Washer

ANTES DE COMENZAR
GUARDE ESTAS INSTRUCCIONES PARA UN USO FUTURO
7302379-100SP 11/18
Los nombres de productos que aparecen en este documento son marcas comerciales de AS America, Inc.
© AS America Inc. 2018
NOTAS:
• Es posible que las imágenes no definan con exactitud el contorno de la cerámica y los componentes.
• Cumpla todas las normas locales de plomería y construcción.
• Consulte los códigos locales y las instrucciones del fabricante para conocer los requisitos de la válvula de descarga.
• Inspeccione con cuidado el nuevo mingitorio para ver si tiene daños.
• Las dimensiones del accesorio son nominales y cumplen con las tolerancias establecidas por la norma ASME A112.19.2.
• La preparación del sitio puede requerir herramientas y accesorios adicionales.
Gracias por elegir American Standard - el parámetro de primera calidad por más de 100 años. Para asegurarse de que el
producto esté instalado correctamente, por favor lea estas instrucciones cuidadosamente antes de comenzar. (Ciertas
instalaciones pueden requerir ayuda profesional.) Asegúrese de que su instalación cumpla con los códigos locales.
!
Serie 6516 Acople Superior & 6517 Acople Posterior
6516 Acople Superior 6517 Acople Posterior
Mingitorio Greenbrook
INSTRUCCIONES DE INSTALACIÓN
PRECAUCIÓN: EL PRODUCTO ES FRÁGIL. ¡MANIPÚLELO CON CUIDADO PARA NO ROMPERLO Y EVITAR
POSIBLES LESIONES!
HERRAMIENTAS Y MATERIALES RECOMENDADOS
Lentes de seguridad Cinta métrica Llave ajustable Lápiz Equipo para cortar orificios
Sellador para roscas Trinquete de 1/4" Destornillador plano Niveles
13 mm
(1/2")
102 mm
(4")
EMPAQUE
2" N.P.T.
ROSCAS
INTERIORES
DETALLE DE LA CONEXIÓN DE SALIDA
PARED
ACABADA
13 mm
(1/2")
13 mm
(1/2")
102 mm
(4")
EMPAQUE
2" N.P.T.
ROSCAS
INTERIORES
DETALLE DE LA CONEXIÓN DE SALIDA
PARED
ACABADA
13 mm
(1/2")
L/C DE
SALIDA
GANCHOS K2
SUELO
ACABADO
PARED
ACABADA
8mm x 25 mm
(5/16" x 1")
RANURA
697 mm
(27-1/2")
102 mm
(4")
411 mm
(16-1/8")
212 mm
(8-3/8")
446 mm
(17-1/2")
420 mm
(16-1/2")
285 mm
(11-1/4")
380 mm
(15")
55 mm
(2-1/8")
67 mm
(2-5/8")
L/C DE
SALIDA
SUELO
ACABADO
PARED
ACABADA
102 mm
(4")
3/4"
ACOPLE
697 mm
(27-1/2")
411 mm
(16-1/8")
212 mm
(8-3/8")
420 mm
(16-1/2")
BOTÓN DE
DESCARGA
MANUAL ALIMENTACIÓN
DE AGUA 20mm
(3/4" I.P.S.)
292 mm
(11-1/2")
108 mm to 133 mm
(4-1/4" to 5-1/4")
285 mm
(11-1/4")
380 mm
(15"
50 mm
(2")
419 mm
(16-1/2")
15
432mm
(17") MAX
610mm (24")
OPTIONAL A
SUELO
ACABADO
432mm
(17") MAX
610mm (24")
OPTIONAL A
SUELO
ACABADO
GANCHOS K2
8mm x 25 mm
(5/16" x 1")
RANURA
121 mm
(4/3/4")
446 mm
(17-1/2")
121 mm
(4/3/4")

a. Cierre el suministro de agua.
b. Instale o reubique la tubería de suministro y el tubo de desagüe conforme sea necesario para cumplir con las
dimensiones calculadas.
c. Instale la válvula de cierre.
d. Instale el marco de soporte adecuado para los ganchos de pared según sea necesario.
e. Determine la posición de la boquilla del tubo de desagüe. Cuando establezca la longitud de la boquilla, tome en cuenta
la longitud del acople de la salida del mingitorio y la distancia en que se enroscará el aro hembra sobre la boquilla del
tubo de desagüe.
NOTA: Agregue un poco más de longitud en la boquilla para permitir que el empaque tenga espacio.
PREPARACIÓN
7302379-100SP 11/18
- 2 -
1
a. Instale los ganchos de pared de acuerdo con los cálculos de la ilustración.
b. Aplique cinta selladora para roscas en las roscas de los tubos e instale el aro hembra en el tubo de desagüe.
c. Coloque el empaque en el aro hembra con la superficie biselada al contrario del aro.
d. Coloque con cuidado el mingitorio en los ganchos de pared.
e. Asegure el mingitorio en el aro hembra con los tornillos y las arandelas provistos.
INSTALE EL MINGITORIO
2
PRECAUCIÓN: RIESGO DE LESIÓN PERSONAL O DAÑO DEL PRODUCTO. MANEJE CON CUIDADO.
LA PORCELANA VÍTREA SE PUEDE ROMPER O DESPOSTILLAR SI EL PRODUCTO SE MANEJA SIN CUIDADO.
!
PRECAUCIÓN: RIESGO DE DAÑO DEL PRODUCTO. NO APRIETE DE MÁS LOS PERNOS.
!
a. Instale la válvula de descarga de acuerdo con las instrucciones del fabricante.
b. Conecte el suministro de agua y complete las conexiones del tubo de desagüe.
c. Abra el suministro de agua.
d. Descargue y revise toda la instalación para ver si tiene fugas.
NOTA: En caso de salpicaduras, ajuste el “cierre angular” como sea necesario.
COMPLETE LA INSTALACIÓN
3
Lave con agua y jabón suave y enjuague bien. Seque con un paño suave. Evite los detergentes, desinfectantes y
productos de limpieza en latas de aerosol porque pueden dañar los accesorios.
CUIDADO Y LIMPIEZA
Ganchos de pared
Soporte Pared
212 mm
(8-3/8")
En los Estados Unidos:
American Standard Brands,
1 Centennial Ave.
Piscataway, New Jersey 08854
Atención: Director de servicio al cliente
Para los residentes en Estados Unidos,
la información de la garantía
puede obtenerse también llamando al siguiente
número sin cargo: [phone]
www.americanstandard.com
En Canadá:
AS Canada, ULC
5900 Avebury Rd.
Mississauga, Ontario
Canada L5R 3M3
Número sin cargo: [phone]
www.americanstandard.ca
En México:
American Standard B&K México,
S. de R.L. de C.V.
Vía Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. México
Número sin cargo: 01-800-839-1200
www.americanstandard.com.mx
Ganchos de
Pared Instalados
Aro Hembra
Empaque
Tornillo
Arandela

AVANT DE COMMENCER....
CONSERVER POUR USAGE ULTÉRIEUR
7302379-100FR 11/18
AVERTISSEMENT: CE PRODUIT EST FRAGILE. POUR ÉVITER LES BRIS ET DES BLESSURES, MANIPULER AVEC SOIN!
Les noms des produits mentionnés dans le présent document sont des marques de commerce de AS America, Inc.
©AS America, Inc. 2018
NOTES:
• Les dessins peuvent ne pas correspondre exactement aux contours de l'appareil ou des composants.
• Respecter tous les codes locaux de plomberie et du bâtiment.
• Se reporter aux codes locaux et aux instructions du fabricant pour les exigences relatives à la valve de chasse.
• Inspecter avec soin le nouvel urinoir afin de déceler tout dommage.
• Les dimensions du robinet sont nominales et sont conformes aux seuils de tolérance établis d'après les
normes ASME A112.19.2.
• La préparation du site peut nécessiter des outils et de la quincaillerie supplémentaires.
Nous vous remercions d'avoir choisi American Standard - synonyme de qualité supérieure depuis plus de 100 ans. Pour être
sûr que ce produit soit bien installé, veuillez lire attentivement ces instructions avant de commencer. (Certaines installations
peuvent requérir une aide professionnelle.) Assurez-vous également que votre installation soit conforme aux codes locaux.
!
Séries 6516 Alímentation Par Le Haut &
6517 Alímentation Par L’arriére
6516 Alímentation Par Le Haut 6517 Alímentation Par L’arriére
Urinoir Greenbrook
INSTRUCTIONS D'INSTALLATION
OUTILS ET MATÉRIAUX RECOMMANDÉS
Lunettes de sécurité Ruban à mesurer Clé universelle Crayon Équipement pour la découpe de trous
Scellant pour filet Cliquet 1/4 po Tournevis à lame Niveaux
JOINT DE
CAOUTCHOUC
13mm
(1/2 po)
13mm
(1/2 po)
102mm
(4 po)
2 po N.P.T.
FILETS INTÉRIEURS
DÉTAILS DE LA CONNEXION DE SORTIE
MUR FINI
JOINT DE
CAOUTCHOUC
13mm
(1/2 po)
13mm
(1/2 po)
102mm
(4 po)
2 po N.P.T.
FILETS INTÉRIEURS
DÉTAILS DE LA CONNEXION DE SORTIE
MUR FINI
L/C DU
DRAIN
PLANCHER
FINI
MUR FINI
8mm x 25 mm
(5/16 po x 1 po)
FENTE
697 mm
(27-1/2 po)
102 mm
(4 po)
121 mm
(4/3/4 po)
411 mm
(16-1/8 po)
212 mm
(8-3/8 po) 446 mm
(17-1/2 po)
420 mm
(16-1/2 po)
102 mm
(4 po)
285 mm
(11-1/4 po)
380 mm
(15 po)
55 mm
(2-1/8 po)
67 mm
(2-5/8 po)
ÉTRIERS K2
121 mm
(4/3/4 po)
446 mm
(17-1/2 po)
L/C DU
DRAIN
PLANCHER
FINI
MUR FINI
3/4 po
RACCORD
697 mm
(27-1/2 po)
411 mm
(16-1/8 po)
212 mm
(8-3/8 po)
420 mm
(16-1/2 po)
BOUTON DE
CHASSE
MANUELLE ALIMENTATION
DN 20mm
(3/4 po I.P.S.)
292 mm
(11-1/2 po)
108 mm to 133 mm
(4-1/4 po to 5-1/4 po)
285 mm
(11-1/4 po)
380 mm
(15 po)
50 mm
(2 po)
419 mm
(16-1/2 po)
15
432mm
(17 po) MAX
610mm (24 po)
EN OPTION À
PLANCHER FINI
432mm
(17 po) MAX
610mm (24 po)
EN OPTION À
PLANCHER FINI
8mm x 25 mm
(5/16 po x 1 po) FENTE
ÉTRIERS K2

a. Couper l'alimentation en eau.
b. Poser ou relocaliser la conduite d'alimentation et le tuyau de drain au besoin afin de se conformer aux dimensions de l'installation brute.
c. Poser la vanne d'arrêt.
d. Poser un cadre de soutien adéquat pour les étriers muraux le cas échéant.
e. Déterminer la position du mamelon du tuyau de drain.Au moment de déterminer la longueur du mamelon, prendre en considération
la longueur de la tête de la sortie de l'urinoir et la distance du filet du collier femelle sur le mamelon du tuyau de drain.
REMARQUE: Ajouter une longueur supplémentaire au mamelon pour laisser l'espace pour le joint.
PRÉPARATION
7302379-100FR 11/18
- 2 -
1
a. Poser les étriers muraux selon la disposition des tuyaux dans l'illustration.
b. Appliquer du ruban scellant sur les filets du conduit et poser le collier femelle sur le tuyau de drain.
c. Placer le joint sur le collier femelle avec la surface biseautée faisant face à l'opposé du collier.
d. Placer avec soin l'urinoir dans les étriers muraux.
e. Fixer l'urinoir au collier femelle en utilisant les vis et les rondelles fournies.
INSTALLER L'URINOIR
2
AVERTISSEMENT: RISQUE DE BLESSURES CORPORELLES OU DES DOMMAGES AU PRODUIT. MANIPULER AVEC SOIN.
LA PORCELAINE VITRIFIÉE PEUT CASSER OU S'ÉCAILLER SI LE PRODUIT N'EST PAS MANIPULÉ AVEC SOIN.
!
AVERTISSEMENT: RISQUE DE DOMMAGES AU PRODUIT. ÉVITER DE TROP SERRER LES BOULONS.
!
a. Poser la valve de chasse selon les instructions du fabricant.
b. Raccorder l'alimentation en eau et finaliser le raccordement du tuyau de drain.
c. Ouvrir l’alimentation en eau.
d. Rincer et vérifier l'ensemble de l'installation afin de déceler toute fuite.
REMARQUE : En cas de projection, ajuster le « robinet angulaire » selon le besoin.
TERMINER L'INSTALLATION
3
Laver avec de l'eau savonneuse et rincer à fond. Essuyer avec un chiffon doux. Éviter les détergents, les désinfectants ou les
produits de nettoyage en aérosol puisqu'ils peuvent endommager les raccords.
ENTRETIEN ET NETTOYAGE
Étriers muraux
Support
Mur
212 mm
(8-3/8 po)
Étriers Muraux
Posés
Collier Femelle
Joint
Vis
Rondelle
Aux États-Unis:
Marques American Standard
1 Centennial Ave.
Piscataway, New Jersey 08854
À l'attention de: Directeur du service à la clientèle
Les résidents des États-Unis peuvent aussi obtenir
de l'information sur la garantie en composant
le numéro sans frais suivant: [phone]
www.americanstandard.com
Au Canada:
AS Canada ULC
5900 Avebury Rd.
Mississauga, Ontario
Canada L5R 3M3
Numéro sans frais: [phone]
www.americanstandard.ca
Au Mexique:
American Standard B&K Mexico
S. de R.L. de C.V.
Via Morelos n° 330
Col. Santa Clara
Ecatepec 55540 Edo. Mexique
Numéro sans frais: 01-800-839-1200
www.americanstandard.com.mx

1M965647 REV. 1.4 (7/15)
© 2015 AS America Inc.
NOTE TO INSTALLER: Please give this manual to the customer after installation.
To learn more about American Standard Selectronic®Products visit our website at: www.americanstandard-us.com
or e-mail us at: CR[email protected]
For Parts, Service, Warranty or other Assistance,
please call (844) CRT-TEAM / [phone] (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-306-1093))
SELECTRONIC®
DC POWERED PROXIMITY EXPOSED
URINAL FLUSH VALVE
0.125, 0.25, 0.5 & 1.0 GPF
Installation Instructions
Certied to comply with ASME A112.19.2
© 2015 AS America, Inc.
CAUTION: Use only American Standard supplied
transformers and cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any components
will void the warranty.
Exposed Flushometer
for 3/4"Top Spud Urinals
CLOG RESISTANT
•Self-cleaning piston valve prevents clogging and reduces maintenance.
ONE SENSOR FITS ALL
•Only 1 sensor for entire Selectronic™ line of faucets, urinals, and
flush valves.
•Range can be adjusted manually or with optional remote control.
•Sensor Features Low Battery Indicator.
MODEL NUMBERS
6063.013 6064.013 6062.601
6063.025 6064.025 6063.505
6063.051 6064.051 6063.510
6063.101 6064.101 6063.513

2M965647 REV. 1.4 (7/15)
Thank you for selecting American-Standard...the benchmark of ne quality for over 100 years.To ensure that your
installation proceeds smoothly--please read these instructions carefully before you begin.
Remove the Flush Valve items from the carton. The illustration below shows all items after they have been
removed from the carton. Some items may be packaged partially assembled to other items.
UNPACKING All American Standard Products Are Water Tested At Our Factory.
Some Residual Water May Remain In The Valve During Shipping.
1. Installation Instructions
2. Flush Valve Body Assembly
3. Vacuum Breaker Tube
4. Spud Coupling Nut and Washers
5. Spud Flange
6. Wall Escutcheon
7. Cover Tube
8. Sweat Adapter
9. Stop Valve
CARE INSTRUCTIONS:
DO: CLEAN THE PRODUCT WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
1
DO NOT REMOVE PROTECTIVE FILM FROM SENSOR
EYE UNTIL INSTALLATION IS COMPLETE.
2
3
4
5
8
6
9
7
NOTE TO INSTALLER: Please give this manual to the customer after installation.
To learn more about American Standard Selectronic®Products visit our website at: www.americanstandard-us.com
or e-mail us at: [e-mail]
For Parts, Service,Warranty or other Assistance,
please call (844) CRT-TEAM / [phone] (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-306-1093))
SELECTRONIC®
DC POWERED PROXIMITY EXPOSED
URINAL FLUSH VALVE
0.125,0.25, 0.5 & 1.0 GPF
Installation Instructions
© 2015 AS America, Inc.
CAUTION: Use only American Standard supplied
transformers and cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any components
will void the warranty.
Exposed Flushometer
for 3/4"Top Spud Urinals
CLOG RESISTANT
•Self-cleaning piston valve prevents clogging and reduces maintenance.
ONE SENSOR FITS ALL
•Only 1 sensor for entire Selectronic™ line of faucets, urinals, and
•Range can be adjusted manually or with optional remote control.
•Sensor Features Low Battery Indicator.
MODEL NUMBERS
6063.013 6064.013 6062.601
6063.025 6064.025 6063.505
6063.051 6064.051 6063.510
6063.101 6064.101 6063.513

3
CAUTION: Use only American Standard supplied
transformers and cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any components
will void the warranty.
M965647 REV. 1.4 (7/15)
1. Installation Instructions
2. Flush Valve Body Assembly
3. Vacuum Breaker Tube
4. Spud Coupling Nut and Washers
5. Spud Flange
6. Wall Escutcheon
7. Cover Tube
8. Sweat Adapter
9. Stop Valve
GENERAL DESCRIPTION:
SELECTRONIC™ PROXIMITY URINAL FLUSH VALVE
Exposed Flushometer for 3/4"Top Spud Fixtures
Exclusive, self cleaning piston-type ush valve with
proximity operation and manual override. Operates
on DC (battery) power. Recommended operating
pressure 35 to 80 psi. Can install left or right-handed.
Detection Zone can also be adjusted manually, or
with optional remote control.
412 mm
(16-1/2")
292 mm
(11-1/2")
120 mm
(4-3/4")
73 mm
(2-7/8")
(1" NPT)
15˚
305 mm MÁX.
(12" MÁX.)
76mm MAX.
(3) MAX.
L-C-
*Note: The Critical Line (-C-L-) on Vacuum
Breaker must typically be 6"(152mm) above
fixture. Consult Codes for details.
FINISHED WALL
108mm-134mm
(4-1/4" TO 5-1/4")
FOR 3/4" TOP
SPUD FIXTURES
MANUAL
OVERRIDE
BUTTON
DETECTION ZONE
400mm-800mm
(15-3/4 TO 31-1/2)
*-C-L-
152mm MIN.
(6") MIN.
Fig. 2
123
4
5
6
7 9 10
8
10'
Roughing-in Dimensions Fig. 1
Right or Left Hand Installation
See (Section 5) for converting Flush
Valve to Left Hand Installation.
RECOMMENDED TOOLS; Fig. 2.
1. Teon Tape
2. Flat Blade Screwdriver
3. Adjustable Wrench
4. Tape Measure
5. Hacksaw
6. Tubing Cutter
7. File
8. For Sweat Connection; Solder and Torch
9. 2.5mm Hex Wrench
10. 1.5mm Hex Wrench
PRIOR TO INSTALLATION
Note: Prior to installing the Selectronic™Flush
Valve the following items must be installed.
1. Urinal
2. Drain line
3. Water supply line
IMPORTANT:
• All plumbing and electrical wiring should be
installed in accordance with applicable codes
and regulations.
• The use of water hammer arrestors is strongly
recommended for commercial applications. All piping
behind the walls should be properly secured and
fastened.
• Water supply lines must be sized to provide an
adequate volume of water for each xture.
• Flush all water lines prior to operation (See Step 4).
Dirt and debris can cause ush valve to run continuously.
• With the exception of Stop Valve Inlet, DO NOT
use pipe sealant or plumbing grease on any
valve component or coupling!
• Protect the chrome or special nish on the Flushometer.
DO NOT USE toothed tools on nished surfaces to install
or service these valves. Also see “Care and Cleaning”
section of this manual.
• This product contains mechanical and/or electrical
components that are subject to normal wear. These
components should be checked on a regular basis and
replaced as needed to maintain the valve’s performance.

4M965647 REV. 1.4 (7/15)
CENTER LINE OF
FIXTURE SPUD
FINISHED WALL
FILE EDGES
SOLDER
ADAPTER
Fig. 3
ADAPTER
32mm
(1-1/4")
A
(A-B)= B
C
CLEAN
Fig. 4a
Fig. 4b
Fig. 4c
1
1
4
2
3
Fig. 4
TEFLON TAPE
FINISHED WALL
X
X
2
1
23
4
5
Fig. 5
3/4" TOP SPUD
FLUSH VALVE INSTALLATION
1INSTALL SWEAT ADAPTER; Fig. 3
Note: Install Optional Sweat Adapter (Supplied) for
copper pipe supply line.
1. Measure the distance (A) from the nished wall to the
center of the inlet spud on the xture.
2. Cut the supply pipe 1-1/4" (A-B=C) shorter than the
measurement taken in Step 1. File any rough edges
off the end of the supply pipe.
3. Clean the end of the supply pipe. Push the threaded
Adapter until it is seated against the internal stop.
Sweat the Adapter to the pipe.
2
INSTALL COVER TUBE, WALL
ESCUTCHEON and STOP VALVE;
Fig. 4
1. Measure from nished wall to rst thread of Adapter or
threaded supply pipe (dimension “X”). Cut COVER TUBE
(1) to length (X). Apply Teon Tape to the threaded end of
the Adapter or supply pipe.
2. Push WALL ESCUTCHEON (2) onto the COVER TUBE (1).
Slide both onto the SUPPLY PIPE (3).
3. Push the COVER TUBE (1) in to expose the threads of
the supply pipe. With a wrench thread the STOP VALVE
(4) onto the SUPPLY PIPE (3). Align and tighten.
4. Pull COVER TUBE (1) against STOP VALVE (4) and push
WALL ESCUTCHEON (2) against nished wall.
3INSTALL VACUUM BREAKER
TUBE; Fig. 5
1. Place the SPUD FLANGE (1) over the spud on
the Fixture.
2. Place FRICTION WASHER (3) and SEAL WASHER
(4) inside SPUD COUPLING NUT (2) and thread
onto Spud. Do not tighten fully.
3. Insert the VACUUM BREAKER TUBE (5) into the
SPUD COUPLING NUT (2) and push it down.
Note: If cutting VACUUM BREAKER TUBE (5) to size, note
that Critical Line (C/L) on Vacuum Breaker must typically
be 6"(152mm) above xture. Consult Code for details.
CAUTION Turn water supplies off before
beginning