American Standard SERIN 2064.461 User manual

M968918 Rev.1.4
Certified to comply with ASME A112.18.1M
U.S. Patent No. 5,819,789
Turn off hot and cold water
supplies before beginning.
CAUTION
Installation
Instructions
2064.461
ROUGHING-IN
DIMENSIONS
1INSTALL VALVE BODY
Determine where the finished wall location will be. This measurement
is very important! Note: The rough-in measurement from the finished
wall is; 1" minimum and 2" maximum. This is a 1" tolerance. See
rough-in illustration above.
Secure FAUCET BODY (1) to cross brace of wall structure
at required height using two wood screws and and pipe brace.
Turn valve to off position. Turn hot and cold supplies on and
check fitting connections for leaks .
Complete wall construction.
WOOD
SCREWS
WOOD SCREWS
and PIPE BRACE
CROSS BRACE
WALL STUDS
Connect HOT water supply to left VALVE inlet and COLD water
supply to right VALVE inlet. Use pipe sealant or Teflon tape for
all threaded connections. For sweat connections, do not make
sweat connections directly to valve body. Damage to seals and
and valve cartridge may occur. Remove all valve parts before
making sweat connections to valve body.
1
HOT
COLD
16"
Recommended Tools
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
Pipe Wrench
Teflon Tape
Plumbers' Putty or
Caulking
SINGLE CONTROL WALL MOUNT FAUCET
IN-WALL LAVATORY FITTING
SERIN™
2-1/8" D.
(54mm) 2" MAX. (51mm) MAX.
1-1/4" O.D.
(32mm) O.D.
HOT COLD
2" D.
(52mm)
2" MAX.
(50mm)
1" MIN.
(25mm)
FINISHED
WALL
FINISHED
WALL
2" D.
(52mm)
9-1/8"
(233mm)
1/2" NPT
INLETS
4-3/8"
(110mm)
2-1/16"
(52.5mm)
2
(50mm)
TYPICAL INSTALLATION
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.

M968918 Rev.1.4
4
3INSTALL HANDLE
2a
DRAIN INSTALLATION
Assembly GASKET (2) WASHER (3) and LOCKNUT (4) onto DRAIN BODY (1).
Tighten LOCKNUT (4) firmly.
Assembly TAILPIECE (5) to DRAIN BODY (1).
Apply a bead of PUTTY to underside of FLANGE on DRAIN BODY (1).
Feed DRAIN BODY (1) down through lavatory. LAVATORY
PUTTY
2
3
4
5
1
2INSTALL WALL SPOUT
INSTALL WALL SPOUT
Install HANDLE (4) onto VALVE STEM (1) and tighten
SET SCREW (5) with 2.5mm HEX WRENCH (6) supplied.
Install PLUG BUTTON (7) into HANDLE (4).
Attach HANDLE ADAPTER (2) to VALVE STEM (1) with
ADAPTER SCREW (3). Tighten fully.
Push VALVE STEM (1) down to off position.
12
5
6
6
11
3
3
Remove PLASTER GUARDS (1, 1a) from VALVE BODY and
SPOUT NIPPLE (2).
Apply thread sealant to SPOUT NIPPLE (2).
Thread SPOUT MOUNT (3) onto SPOUT NIPPLE (2) using a
10mm Hex Wrench. Tighten completely.
Install SEAL (4) into SPOUT ESCUTCHEON (5).
Place SPOUT ESCUTCHEON (5) with SEAL (4)
onto SPOUT (6). Fig. A
Push SPOUT (6) onto SPOUT MOUNT (3).
Align SPOUT (6) and tighten SPOUT SET
SCREW (7) with 2mm HEX WRENCH
(8) supplied. Push SPOUT ESCUTCHEON
(5) against finished wall.
APPLY
SEALANT
4
7
9
8
10
3
7
1a
10mm HEX
WRENCH
Fig. A
Fig. B
Install SEAL (9) into VALVE
ESCUTCHEON 10). Place VALVE
ESCUTCHEON (10) with SEAL (9)
onto VALVE (11). Push VALVE
ESCUTCHEON (5) against finished wall. Fig. B
1
2
4
5
6

M968918 Rev.1.4
6TEST INSTALLED FAUCET
7
8
Turn HANDLE to "off" position.
Remove AERATOR (1) using TOOL (2) supplied.
Check all drain connections for leaks.
Turn handle to OFF position.
Replace AERATOR (1).
Turn hot and cold water supplies on. Operate
HANDLE to flush water lines thoroughly.
Check spout connections for leaks.
1
2
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
2
5
6
7
8
9
1
3
4
SERVICE
To remove or replace cartidge
Turn valve to OFF position.
Pull out PLUG BUTTON (1) and remove HANDLE SCREW (2).
Pull off HANDLE (3) and CAP (4).
Unthread CARTRIDGE NUT (5) and remove.
Pull out CARTEIDGE (6).
Inspect CARTRIDGE (6) and O-RINGS (7) for debris and
clean if necessary.
Clean MANIFOLD (8) and rinse clean.
Reinstall CARTRIDGE (6) and O-RINGS (7) onto MANIFLOD (8).
Reinstall CARTRIDGE NUT (5), CAP (4) and HANDLE
ASSEMBLY (3).
If spout drips, operate handle several times from OFF to
ON and HOT to COLD position. Do not force - handles
turn only 90˚.
Turn off hot and cold water
supplies before beginning.
CAUTION
ADJUST HOT LIMIT SAFEYT STOP
By restricting HANDLE rotation and limiting the
amount of hot water allowed to mix with the cold,
the HOT LIMIT SAFETY STOP (9) reduces risk of
accidental scalding. To lower the maximum hot
water temperature of your faucet, all you need to
do is adjust the setting on the HOT LIMIT SAFETY
STOP (9). Note: The HOT LIMIT SAFETY STOP (9)
is set at the maximum hot temperature setting
from the factory.
A
BD
GEAR
GEAR
GEAR
10
9
9C
10
9
+HOTTER SETTING
MARKS
COLDER
GEAR
10
9
To adjust HOT LIMIT SAFETY STOP:
Remove HANDLE ASSEMBLY (3), CAP (4) and CARTRIDGE NUT (5).
Set the CARTRIDGE STEM (10) to the OFF position and rotate it
clockwise until stops. Fig. B.
Rotate the CARTRIDGE STEM (10) counter-clockwise to a colder
setting mark in the HOT LIMIT SAFETY STOP (9). Fig. C.
Lift up the HOT LIMIT SAFETY STOP (9) and rotate it to coincide
again with the stop in the base of the CARTRIDGE STEM (10). Fig. D.
Replace the HOT LIMIT SAFETY STOP (9).
Reinstall CARTRIDGE NUT (5), CAP (4) and HANDLE ASSEMBLY (3).

M968918 Rev.1.4
SERIN™
SINGLE HANDLE WALL MOUNT
LAVATORY FAUCET
MODEL NUMBER
M962419-YYY0A
HANDLE KIT
015025-YYY0A
DRAIN COMPLETE
070532-0040A
TAILPIECE
M962513-YYY0A
SPOUT ASSEMBLY
M962511-0070A
SPOUT MOUNTING KIT
M962512-YYY0A
SPOUT ESCUTCHEON KIT
607641-YYY0A
CARTRIDGE CAP
M962757-0070A
AERATOR
CHROME
SATIN NICKEL
002
295
Replace the "YYY" with
appropriate finish code
2064.461
603275-0070A
LOCK NUT
605779-YYY0A
VALVE COVER
M962514-YYY0A
VALVE ESCUTCHEON KIT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
IN MEXICO 01-800-839-1200
M951472-0070A
CARTRIDGE