American Standard Ardsley 4962.150 User manual

TRADITIONAL VESSEL FAUCET
ARDSLEY
Installation
Instructions
Certified to comply with ANSI A112.18.1
4962.150
4962.151
Recommended Tools & Materials
Adjustable Wrench Channel Locks Regular Screwdriver
Plumbers' Putty or
Caulking
1INSTALL FAUCET Turn off hot and cold water
supplies before beginning.
CAUTION
NOTE; The FAUCET with EXTENSION is used for
installation with above-counter sinks.
With the collar of the EXTENSION (1) facing up slide
the EXTENSION (1) over the FAUCET SUPPLIES (2) and
the MOUNTING STUD (3). The collar of the EXTENSION (1)
fits into the groove of the faucet.
Seat SEAL (4) into groove in EXTENSION (1) base.
Feed FAUCET SUPPLIES (2) and MOUNTING STUD (3)
through mounting hole of deck.
From below, push RETAINING WASHER and GASKET (5) onto
MOUNTING STUD (3). Secure Faucet with MOUNTING NUT (6),
pulling faucet to front of sink, so STUD (3) rests against mounting
hole. Before final tightening, adjust faucet so that it is centered.
Tighten MOUNTING NUT (6) to complete installation.
For single hole only.
FAUCET
GROOVE
COLLAR
5
3
4
1
6
GROOVE
(EXTENSION
BASE)
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
2
M968847
MOUNTING
SURFACE

M968847
2MAKE WATER SUPPLY CONNECTIONS
LOOP SUPPLIES
IF REQUIRED
10"
1
2
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply to Hot and right supply to the Cold wall
supply. Use adjustable wrench to tighten
connections. Do not over tighten.
Faucet supplies are 10" long from faucet base.
Note: If additional supply length is required,
installer must purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
Figure A.
COLD
COLD
HOT
HOT
3DRAIN INSTALLATION
Assembly GASKET (2) WASHER (3) and LOCKNUT (4)
onto DRAIN BODY (1). Tighten LOCKNUT (4) firmly.
Assembly TAILPIECE (5) to DRAIN BODY (1).
Apply a bead of PUTTY to underside of
DRAIN BODY FLANGE (1).
Feed DRAIN BODY (1) down through lavatory.
PUTTY
Figure A.
2
1
3
4
5

M968847
Remove as much surface dirt and film using clear
water and soft cotton cloth (as described above).
Use any of the following to remove tough surface
film and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.
To keep your new faucet looking new, please follow
these simple care instructions:
DO: Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
CARE INSTRUCTIONS:
6
Failure to follow these care instructions may
damage the Faucet's finish.
4
5
TEST INSTALLED FAUCET
AND CHECK FOR LEAKS 1
2
3
3
1
2
By restricting handle rotation and limiting the amount of hot water allowed
to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental
scalding. To set the maximum hot water temperature of your faucets, all you
need to do is adjust the setting on the HOT LIMIT SAFETY STOP .
Loosen SET SCREW (2) with 2.5mm hex wrench. Pull HANDLE (1) off valve
stem. Pull off CAP (3). Use a flat blade screwdriver or your fingers to pull up
and rotate red HOT LIMIT SAFETY STOP (4). Follow Step "A" or "B" to adjust
min./max. discharge temperature. "0" being the hottest to "7" the coldest
temperature setting. Factory set at "0".
Replace ESCUTCHEON CAP (3), HANDLE (1), tighten
HANDLE SCREW (2).
HOT LIMIT SAFETY STOP ADJUSTMENT
PRY RED RING FORWARD
AND ROTATE COUNTER-
CLOCKWISE ONE CLICK
PRY RED RING FORWARD
AND ROTATE CLOCKWISE
"A"
ADJUSTMENT WHEN
WATER IS TOO HOT
"A"
"A"
"B"
"B"
ADJUSTMENT WHEN
WATER IS TOO COLD
"B"
3&%3*/()05
-*.*54"'&5:4501
5&.1&3"563&
4&55*/(/6.#&34


































4
COLD
HOT
With HANDLE (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Remove AERATOR (3).
Operate HANDLE (1) to flush water lines thoroughly.
Replace AERATOR (3).