American Standard DXV Fresno D35403300 User manual

- 1 -
INSTALLATION INSTRUCTIONS
SAVE FOR FUTURE USE
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2013
In the United States:
DXV by American Standard
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV by American Standard
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV by American Standard
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Thank you for selecting DXV by American Standard. To ensure that
your installation proceeds smoothly, please read these instructions
carefully before you begin.
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing,
supply stores. It is essential that the tools and materials be on hand before work is begun.
M965559 Rev. 1.5 (3/15)
Model D35403300
Fresno®
Single Control Kitchen
Faucet with Pull-Down Spray
ROUGHING-IN DIMENSIONS:
• For reference
Plumbers' Putty or CaulkingChannel Locks
Phillips Screwdriver
Flat Blade Screwdriver Adjustable Wrench
7-3/4"
(197 mm)
9"
(229 mm)
16-3/8"
(416 mm)
6"
(153mm)
2"
(51 mm)
1-3/8" to 1-1/2" D.
(33 to 38 mm)
MOUNTING HOLE 15-3/4"
(400 mm)
28-7/8"
(733 mm)
3/8" (10 mm) COMPRESSION
FLEXIBLE SUPPLIES
60 mm
(2-3/8")
49 mm
(1-7/8")

- 2 -
2
3
MAKE WATER SUPPLY CONNECTIONS
CONNECT HOSE SPRAY and INSTALL WEIGHT
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on tting supplies are 3/8" (10 mm) compression.
Connect left supply (Marked with a Red Stripe) to Hot and right
supply (Marked with Blue Stripe) to Cold wall supply. Use
adjustable wrench to tighten connections. Do not over tighten.
• Faucet supplies are 27-1/2" (699 mm) long from faucet base.
Note: If additional supply length is required, installer must
purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are too long, loop as
illustrated to avoid kinking.
• Check that seal washers are installed in both ends of
SPRAY HOSE ADAPTER (1). Thread SPRAY HOSE
ADAPTER (1) onto faucet SHANK (2).
Tighten with adjustable wrench. Figure 1.
• Thread HOSE END (3) into bottom of SPRAY HOSE
ADAPTER (1). Tighten with adjustable wrench.
Make sure all connections are tight. Figure 1.
• Install RUBBER BUSHING (4) onto SPRAY HOSE (5).
Install WEIGHTS (6) onto HOSE (5) using two screws
(7). Locate WEIGHTS (6) 18” from underside of
mounting surface on HOSE (5). Tighten
SCREWS (5) rmly. Figure 2.
M965559 Rev. 1.5 (3/15)
1INSTALL FITTING
CAUTION Turn off hot and cold wate
supplies before beginning.
• Make certain the O-RING SEAL (1) is properly seated in recess of faucet body.
• Insert supply HOSES (2), SHANK (3) and SPRAY HOSE (4) through center hole
of sink or mounting surface.
• Assemble RUBBER WASHER (5), PLASTIC WASHER (6), RUBBER & METAL
“C” WASHERS (7) and long LOCKNUT (8) onto SHANK (3) from underside of sink.
Hand tighten LOCKNUT (8) and check that faucet is centered.
• Tighten LOCKNUT (8) with WRENCH.
• Feed HOSE END (9) through HOSE GUIDE (10). Slide other side of HOSE GUIDE (10)
onto SHANK (3) and secure with LOCK NUT (11). Do not over tighten!
1
3
2
5
7
6
8
9
10
11
RECESS
4
RED
STRIPE
BLUE
STRIPE
1
2
COLD
HOT
Figure 2
SEAL
WASHER
SEAL
WASHER
2
1
3
5 7
64
UNDER SIDE
OF MOUNTING
SURFACE
Figure 1
18"
(457mm)

- 3 -
3TEST INSTALLED FAUCET
SERVICE
• Move HANDLE (1) into “off” position.
• Unthread SPRAY HOSE (3) from SPRAY (2).
• Turn on water supplies and check connections for leaks.
• Hold HOSE END (3) in sink and operate HANDLE (1) on and off,
hot and cold to ush water lines thoroughly. Replace SPRAY (2).
• Pull SPRAY (2) out and check hose and supply connections
for leaks. Check that SPRAY HOSE (3) and WEIGHT (4) slide
up and down freely and do not interfear with supplies or waste
outlet plumbing.
• Check all drain connections for leaks.
• Move HANDLE (1) to “off” position.
• Clogged CARTRIDGE outlets or inlets may cause
reduced flow.
To clean, rst turn off water supply then:
• Loosen and remove LEVER HANDLE (1). Loosen
HANDLE SCREW (2) with 2.5mm Hex Wrench and
then pull HANDLE BASE (3) off.
• Unscrew ESCUTCHEON CAP (4). Unscrew the
CARTRIDGE NUT (5).
• Remove CARTRIDGE (6). Clean inlets of
CARTRIDGE (6) and MANIFOLD (7).
• Reassemble CARTRIDGE (6). Replace CARTRIDGE
NUT (5), CAP (4) and HANDLE assembly, check ow.
•If SPOUT (7) leaks at swivel point the O-RINGS (8)
need to be replaced. To remove SPOUT (7):
• Loosen the SPOUT SET SCREW (9) with
a 3mm Hex wrench.
• Rotate the SPOUT (7) side to side while pulling
upward to remove SPOUT (7) from faucet body.
• Replace the defective parts, grease O-RINGS (8)
then push SPOUT (7) back into position.
Tighten SET SCREW (9).
• Check that SPOUT (7) rotates freely and
does not leak at the swivel point.
5
4
M965559 Rev. 1.5 (3/15)
1
25
3
3
4
HOT & COLD SUPPLIES
9
8
11
3mm
HEX WRENCH
12
1
3
4
5
6
CLEAN
7
REMOVE
INSTALL
10
2

- 4 -
M962648-0070A
SPOUT BUSHING
& O-RING KIT M962690-0070A
CARTRIDGE NUT
M962691-YYY0A
CARTRIDGE COVER
M964406-0070A
CARTRIDGE
M964722-YYY0A
HANDLE KIT
M962659-0070A
MOUNTING KIT
M962650-0070A
HOSE WEIGHTS
M962683-YYY0A
PULL-OUT SPRAY
WITH CHECK VALVE
M962652-0070A
SPOUT SET SCREW
M964728-YYY0A
SPOUT ASSEMBLY
M964993-1000A
NYLON SPRAY HOSE
AND SEALS
M964725-YYY0A
PEDESTAL
M962660-0070A
HOSE GUIDE
M962661-0070A
MOUNTING NUT
M911764-0070A
SEAL WASHER
M962662-0070A
SPRAY HOSE ADAPTER
MODEL NUMBER
D35403300
Fresno®
Single Control Kitchen Faucet
with Pull-Down Spray
M965559 Rev. 1.5 (3/15)
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 100
ULTRA STEEL 355