American Standard FERN 2003.101 User manual

Certied to comply with ANSI A112.18.1
Installation
Instructions
Adjustable WrenchScrewdriver Channel Locks
Recommended tools
8
4
1
2
1INSTALL FAUCET Turn off hot and cold water
supplies before beginning.
CAUTION
GROOVE
(FAUCET
BASE)
MOUNTING SURFACE
Seat SEAL (1) into under side of FAUCET BASE (2). Fig. A.
Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and LIFT ROD (8)
through the mounting hole of lavatory or mounting surface. Fig. A.
From below, push GASKET (7) with RETAINING WASHER (5) onto
MOUNTING STUD (4). Install MOUNTING NUT (6)
onto MOUNTING STUD (4). Fig. B.
Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6)
to complete faucet mounting.
2003.101
FERN
Fig. A.
M965263 REV. 1.9 (8/17)
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
™
Monoblock Bathroom Sink Faucet
with Conventional Pop-up Drain
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
Fig. B.
6
4
7
5
3

APPROX. 20"
COLD
HOT
3/8" COMPRESSION
RED
BAND
BLUE
BAND
MAKE WATER SUPPLY
4
5
Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on tting supplies are 3/8" compression. Connect
left SUPPLY (1) to Hot (Marked with a Red Band) and right supply
to COLD (2) wall supply.
Faucet supplies are 20" long from faucet base.
Note: If additional supply length is required, installer must
purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are to long, loop as
illustrated to avoid kinking.
M965263 REV. 1.9 (8/17)
TEST INSTALLED FITTING and CHECK DRAIN CONNECTIONS
Operate POP-UP KNOB (4) and ll lavatory with water.
Check that DRAIN STOPPER (5) makes a good seal
and retains water in SINK. If DRAIN STOPPER (5)
does not seal properly, adjust POP-UP ROD (6).
Release POP-UP KNOB (4) down and check all drain
connections and "P" trap for leaks. Tighten
if necessary.
With HANDLE (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Remove AERATOR (3).
Operate HANDLE (1) to ush water lines thoroughly.
Replace AERATOR (3).
2
3
INSTALL POP-UP DRAIN
ASSEMBLE PIVOT ROD
TO POP-UP DRAIN
Install FOAM GASKET (4) onto BODY (2).
Install FLANGE (1) onto BODY (2).
Tighten LOCK NUT (3) with channel locks.
Do not over tighten.
2
5
2
“P” TRAP
AERATOR
KEY
WASTE
OUTLET
3
6
4
1
1
2
Unthread PIVOT NUT (1) from drain body.
Remove CLIP (2) from pivot rod (3).
Insert PIVOT ROD (3) through PIVOT NUT (1) as shown,
making sure the SEALS (4) are in place.
Thread PIVOT NUT (1) onto drain body.
Insert PIVOT ROD (3) through second or third hole in
EXTENSION (5), installing CLIP (2) as shown, to keep
EXTENSION (5) in place.
Insert POP-UP ROD (6) through faucet body and through
EXTENSION (5). Tighten EXTENSION NUT (7) to secure it.
ON
COLD
HOT
OFF
2
4
1
3
3
1
2
5
6
7
4

M965263 REV. 1.9 (8/17)
3mm
HEX WRENCH
FRICTION WASHER
Pull out INDEX BUTTON (1). Loosen HANDLE SCREW (2) with 2.5mm Hex Wrench, then
pull HANDLE (3) off.
Unthread ESCUTCHEON CAP (4). Unthread the CARTRIDGE NUT (5).
Remove CARTRIDGE (6). Clean inlets of CARTRIDGE (6) and MANIFOLD (7).
Reassemble CARTRIDGE (6). Replace CARTRIDGE NUT (5), CAP (4) and HANDLE assembly, check ow.
SERVICE
Clogged CARTRIDGE outlets or inlets may cause reduced
flow. To clean, rst turn off water supply then:
2
11
3
1
4
5
6
7
If SPOUT (10) leaks at swivel point the O-RINGS (9) need
to be replaced. To remove SPOUT (10):
Loosen the SPOUT SET SCREW (8) with a 3mm Hex wrench. (Supplied)
Rotate the SPOUT (10) side to side while pulling upward to remove SPOUT (10) from faucet body.
Replace the defective parts and grease O-RINGS (9) with plumber’s grease. Push SPOUT (10) back into position.
Tighten SET SCREW (8).
Check that SPOUT (10) rotates freely and does not leak at the swivel point.
REMOVE
INSTALL
10
9
8
CLEAN
AERATOR (11) and HOSE FILTER SCREENS (12) may accumulate debris causing distorted or reduced water ow.
Remove AERATOR (11) and/or water supplies and rinse clean.
12
6

M965263 REV. 1.9 (8/17)
Monoblock Bathroom Sink Faucet
with Conventional Pop-up Drain
MODEL NUMBER
2003.101
M964185-0020A
POP-UP ROD
M964406-0070A
CARTRIDGE
M964241-0070A
FLOW CONTROL
M964226-0020A
CARTRIDGE COVER
M964316-0020A
HANDLE KIT
RETAINER KIT
M964224-0070A
SPOUT KIT
M964229-0020A
FERN™
CHROME 002
Appropriate finish code
M962648-0070A
SPOUT BUSHING
& O-RING KIT
M970019-0070A
AERATOR KIT
M964332-0020A
HANDLE KIT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are
trademarks of AS America, Inc.
© AS America, Inc. 2017
M953475-0020A
DRAIN ASSEMBLY
M970342-0070A
FILTER SCREENS