American Standard Silhouette 38 User manual

G19
© 2008 AS America Inc. Revised 2/08
SILHOUETTE™ 38" DUAL LEVEL KITCHEN SINK
• Americast® brand engineered material
• Dual level double bowl design
• Titanium enamel - heat resistant up to 1000°
• Acid-resisting glossy porcelain nish
• Top mount or undercounter installation
• Fits most standard 36" cabinet bases
• Silicone sealant supplied
• Available in 1, 3, 4, or 5 faucet hole
conguration
• Customized hole punchings available
(see page G56)
Top Mount/Undercounter:
❏ 7196.001 Center hole only
❏ 7196.803 3 hole
❏ 7196.804 4 hole
❏ 7196.805 5 hole
Undercounter Installation Order:
❏ 791001-100 Mounting Kit (consists of
cut-out templates and mounting clips)
Nominal Dimensions:
965 x 559 x 241mm
(38" x 22" x 9-1/2")
Bowl sizes:
Right Hand: 318mm (12-1/2") wide
413mm (16-1/4") front to back
178mm (7") deep
Left Hand: 527mm (20-3/4") wide
476mm (18-3/4") front to back
229mm (9") deep
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.4M for Americast Plumbing Fixtures
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
* See faucet section for available models
To Be Specied:
❏ Color:
❏ Faucet*:
❏ Faucet Finish:
❏ Basket Strainer: 4331.013
❏ Soap Dispenser: 4503.115, (specify color):
❏ Traps:
Optional Accessories:
❏ Large Wood Cutting Board: 9000.250
❏ Small Wood Cutting Board: 9000.185
❏ Colander for Cutting Board: 8102.100, Color:
❏ Large Colander: 8103.100, Color:
❏ Web Cover: 8106.100, Color:
❏ Bottom Sink Rack (Left): 7407.100, Color:
SILHOUETTE™ 38"
DUAL LEVEL SINK
AMERICAST®
Shown here as a Top Mount (faucet not included)
SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS

G20
© 2008 AS America Inc.
7196.803/804/805 Top Mount
Undercounter Mount
NOTES:
* TEMPLATE PROVIDED WITH MOUNTING KIT 791001-100 FOR
EXPOSED FAUCET DECK OR UNDERCOUNTER FAUCET DECK
COUNTERTOP CUTOUT VARIATIONS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
NOTES:
* COUNTERTOP CUTOUT 527mm x 933mm x 25mm RADIUS
(20-3/4 X 36-3/4 WITH 1" RADIUS) AT CORNERS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
3-1/2"
(89mm)
DIA.
2-1/8"
(54mm)
2"(51mm)
OPTIONAL
FINISHED WALL
OR SPLASHBACK
7-7/8"
(200mm)
8-1/8"
(206mm)
1-1/2"(38mm) DIA.
HOLES TYP.
C/L 3/16"
(5mm)
12-1/4"
(311mm)
11-1/8"
(283mm)
19"
(483mm)
38"
(965mm)
9-1/8"
(232mm)
5-3/4"
(146mm)
SEALING
COMPOUND
7-1/8"
(181mm)
36"(914mm)
SUGGESTED
FINISHED
FLOOR
COUNTERTOP
(BY OTHERS)
22"
(559mm)
*CUTOUT NOTE
7196.804
4 HOLE
7196.805
5 HOLE
1-1/2"
(38mm)
RAD.TYP.
1-1/2 O.D. TAILPIECE
5-3/4"
(146mm)
4"(102mm)
4"(102mm)4"(102mm) 4"(102mm)
1/2"
(13mm)
3/16"
(5mm)
4"(102mm)
4"(102mm)4"(102mm) 4"(102mm)
2" (51mm) OPTIONAL
FINISHED WALL
OR SPLASHBACK
7-7/8"
(200mm)
8-1/8"
(206mm)
1-1/2"
(38mm) DIA.
HOLES TYP.
C/L
SEALING
COMPOUND
FINISHED FLOOR
COUNTERTOP
(BY OTHERS)
*CUTOUT
NOTE
7196.804
4 HOLE
7196.805
5 HOLE
1-1/2" O.D.
TAILPIECE
MOUNTING CLIP
(SEE DETAIL)
DETAIL OF MOUNTING CLIP
(KIT No.791001 -100)
BRASS INSERT
3/4 " MIN.
REFER TO INSTRUCTIONS
PROVIDED WITH KIT FOR
ADDITIONAL INFORMATION
CLIP
MACH.
SCREW
SINK
3-1/2"
(89mm)
DIA.
2-1/8"
(54mm)
12-1/4"
(311mm)
11-3/16"
(284mm)
19"
(483mm)
38"
(965mm)
22"
(559mm)
1-1/2"
(38mm)
RAD.TYP.
5-3/4"
(146mm) 36" (914mm)
SUGGESTED
5-3/4"
(146mm)
9-1/2"
(241mm)
7-1/2"
(191mm)
SILHOUETTE™ 38"
DUAL LEVEL SINK
AMERICAST®
Revised 2/08