American Standard Right Height Elongated Toilet Triumph Cadet... User manual

RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure
Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level
1REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
SAVE FOR FUTURE USE
3
2
CLOSET FLANGE
CLOSET BOLTS
7301270-100 Rev. D
A
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2009
NOTE: Pictures may not exactly define contour of china and components.
ANTIQUITY CADET®3 - 1.6 GPF ONE-PIECE TOILET, MODEL 2907
COMPACT CADET®3 - 1.6 GPF ONE-PIECE TOILET
COMPACT CADET®3 FloWise™ - 1.28 GPF ONE-PIECE TOILET
ROUGHING-IN DIMENSIONS NOTE: Distance from wall to closet flange centerline must be as listed below:
4
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and install wax
ring evenly around waste flange (horn), with tapered end of ring
facing toilet. Apply a thin bead of sealant around toilet base.
WAX RING
SEALANT
Model 2568 – Compact Elongated Right Height™ with Seat
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure
your installation conforms to local codes.
!
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90°, and slide
into place 6" (152 mm) apart and parallel to wall.
724mm
(28-1/2)
159mm
(6-1/4)
16 ± 6mm
(5/8 ± 1/4)
419mm
(16-1/2)
292mm
(11-1/2)
267mm
(10-1/2)
724mm
(28-1/2)
381mm
(15)
394mm
(15-1/2)
79mm
(3-1/8)
FINISHED WALL
422mm
(16-5/8)
305mm
(12)
C/L OF OUTLET
241mm
(9-1/2)
140mm
(5-1/2)
SUPPLY
AS
REQ'D
*FINISHED
FLOOR
C/L OF SEAT
POST HOLES
140mm (5-1/2)
CENTERS
276mm
(10-7/8)
360mm
(14-3/16)
235mm
(9-1/4)
419mm
(16-1/2)
462mm
(18-3/16)
C/L OF SEAT POST
HOLES 140mm
(5-1/2) CENTERS
INSTALLATION INSTRUCTIONS
COMPACT CADET 3ANTIQUITY CADET 3
C/L OF OUTLET
C/L OF SUPPLY
AS REQUIRED
FINISHED WALL
FINISHED
FLOOR
737mm
(29")
225mm
(8-7/8")
(5")
714mm
(28-1/8")
127mm
83mm
(3-1/4")
12.7mm
(1/2")
305mm
(12")
457mm
(18")
C/L

7301270-100 Rev. D
7INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
- 2 -
8a 8b
Before continuing, determine the type of water supply connecation you have from
the chart below and use the appropriate assembly parts required to properly
reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
These parts must be used as
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in
water leakage. Water supply
tube or pipe must extend at
least 1/2" inside threaded
shank of valve (does not apply
to flanged tubing).
Use existing
coupling nut
and washer.
Use existing spiral
cone washer.
Fluidmaster cone
washer may not
seal completely on
spiral type supply
line.
Captive cone
washers already
included. No
additional washers
needed.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
METAL/COPPER
FLARED TUBING
METAL FLANGED
TUBING
METAL SPIRAL
TUBING
VINYL/BRAIDED
CONNECTOR
LOCK NUTLOCK NUT LOCK NUT LOCK NUT
COUPLING
NUT
COUPLING
NUT
EXISTING
COUPLING
NUT
COUPLING
NUT
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
CONE
WASHER
EXISTING
CONE
WASHER
EXISTING
WASHER
With correct washers in place
(see Step 8a), tighten
COUPLING NUT 1/4 turn beyond
hand tight. DO NOT
OVERTIGHTEN.
6INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking
motion, press bowl down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly seated on floor.
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b. Install caps on washers. (If necessary, cut bolt height to
size before installing caps.)
c. Smooth off the bead of sealant around base. Remove
excess sealant.
!
5POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet
flange so bolts project through mounting holes.
b. Loosely install retainer washers and nuts. Side of
washers marked "THIS SIDE UP" must face up!
WASHER
NUT
FLANGE
BOLT
T
H
I
S
S
I
D
E
U
P
BOLTS CLOSET FLANGE
BOLT CAP

7301270-100 Rev. D
9 10
ADJUSTMENTS
a. Adjust water level. Water level
should be adjusted to level indicated
on tank by adjusting float cup.
See Step 10 for water level adjustment
method.
b. If bowl fails to siphon, an adjustment
may be required with the lift chain.
Simply remove the bead chain from
the retainment clip (see Fig. 9A) and
take up slack on the chain, and
reinsert on lift rod. Make sure the chain
is not too taught.
11
- 3 -
CARE AND CLEANING
When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents,
disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some
bathroom chemicals and cosmetics may damage the seat's finish.
WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the
tank. This damage can cause leakage and property damage.
American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing
chlorine (calcium hypochlorite).
!
TANK
LEVER
"S"
CLIP
FLUSH
VALVE
TOP ARM
NIPPLE
Diagram 1
PARTS FOR WATER
CONNECTION
(SEE STEP 9)
CONE WASHER
VALVE
BODY
FLAPPER
THREADED
SHANK
SHANK
WASHER
COUPLING NUT
(HAND TIGHT ONLY)
FILL
VALVE
FLOAT
CUP
CRITICAL LEVEL
MARK ("C.L.")
MUST BE
1" ABOVE
OVERFLOW PIPE
REFILL
TUBE
ADJUSTABLE
HEIGHT
WATER LEVEL
ADJUSTMENT
ROD
LOCK NUT
Fig. 9A
Turn on water supply.
Submerge the FLOAT CUP
under the water for 30
seconds. Adjust the water to
desired level by turning
WATER LEVEL ADJUSTMENT
ROD and moving FLOAT CUP
up or down.
COMPACT CADET®3 ONE PIECE REPAIR PARTS LIST
NOTE: "XXX" represents color options. Specify when ordering.
Repair parts are determined by toilet tank number wich can be found marked inside tank.
TRIP
LEVER
TANK COVER
BOLT
CAPS
SEAT POST
MTG. KIT
SEAT AND COVER
(INCLUDES MTG. KIT)
FLAPPER
ASSEMBLY
FLUSH VALVE
FLUIDMASTER
WATER CONTROL
DESCRIPTIONCOMPONENT 1.6
GPF
1.28
GPF
Tank Cover
Tank Cover
Seat - Elongated
Seat - Elongated
Bolt Cap Kit
Trip Lever - Left Hand
Trip Lever - Left Hand
Trip Lever - Right Hand
Inlet Valve
Inlet Valve
Flush Valve - 1.6 GPF
Flush Valve - 1.6 GPF
Flapper Assembly - 1.6 GPF
Flush Valve - 1.28 GPF
Flapper Assembly - 1.28 GPF
735125-XXX0A
735139-XXX0A
5332.016.XXX
5357.016.XXX
034783-XXX0A
738903-XXX0A
7381084-XXX0A
738919.XXX0A
738565-409.0070A
738565-440.0070A
738942-1000A
738942-1030A
738920-0070A
738942-1020A
7381043-4000A
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
1.6
GPF
2568 2907
√
√
√
√
√
√
√

7301270-100 Rev. D
12
TROUBLESHOOTING GUIDE
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Does not flush a. Water supply valve closed. a. Open valve and allow water to fill tank.
b. Supply line blocked. b. Shut off water supply, disconnect supply line, and inspect
all gaskets and washers. Reassemble. Also, see Fluidmaster
maintenance (see step 12).
c. Flush valve chain too loose or disconnected. c. Readjust chain length as required.
d. Sand or debris lodged in water control. d. Shut off water supply. Remove cap and clean per Step 12.
Poor or sluggish flush a. Bowl water level too low. a. Check that refill tube is connected to water control and
inserted into tank overflow without being kinked or damaged.
b. Supply valve partly closed. b. Open supply valve fully. Be sure that proper supply tube size is used.
c. Partially clogged trapway and/or drain pipe and/or vent. c. Remove obstruction. Consult a plumber if necessary.
d. Supply pressure too low. d. Normal supply pressure must be at least 20 psi.
Toilet leaks a. Poor supply line connection. a. Review Step 8 of installation procedure.
b. Poor bowl to tank/floor connection. b. Review Step 4 through 6 of installation procedure.
Toilet does not shut off a. Flush valve chain too tight, holding flush valve open. a. Readjust chain length as needed. Review step 9.
b. Flush valve seat and/or flapper worn or deformed. b. Replace flapper/flush valve assembly, as needed.
c. Sand or debris lodged in water control. c. Shut off water supply. Remove cap and clean per Step 12.
- 4 -
In the United States:
American Standard Brands
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.americanstandard-us.com
In Canada:
AS Canada ULC
2480 Stanfield Rd.
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: [phone]
www.americanstandard.ca
In Mexico:
Customer Service Manager
AS Maquila, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
www.americanstandard.com.mx
• Make sure water supply is
off. Remove valve TOP by
lifting arm and rotating top
and arm 1/8 turn
counterclockwise, pressing
down slightly on cap.
IMPORTANT: Always
clear sand and rust from
system.
• While holding a
container over the
uncapped VALVE to
prevent splashing, turn
water supply on and off
a few times. Leave
water supply off.
• Replace TOP by engaging
lugs and rotating 1/8 turn
clockwise. MAKE
CERTAIN TIP IS TURNED
TO THE LOCKED
POSITION. VALVE MAY
NOT TURN ON IF TOP IS
NOT FULLY TURNED TO
THE LOCKED POSITION.
For troubleshooting information please contact:
TROUBLESHOOTING
IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK
SLOWLY, repeat Step 12.
IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF
NON-USE, it is a signal you are wasting water because:
• The end of the refill tube is inserted into overflow pipe, below
water level in tank. Attach refill tube to overflow pipe using "S"
clip provided.
• The flush valve is leaking because it's worn, dirty or misaligned
with tank ball or flapper (replace with a new flapper).
IF FILL VALVE WON'T TURN ON OR SHUT OFF or REFILL
OF TANK WATER IS SLOW after valve has been in use for
some time, Fluidmaster Model 242 Replacement Seal may be
needed.
Go to our website at www.fluidmaster.com for more
solutions to toilet problems.
© 2001 Fluidmaster, Inc.
® Registered trademark of Fluidmaster, Inc.
Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. Fluidmaster
shall not be responsible or liable for any damages caused by products used with Fluidmaster valves
that were not manufactured by Fluidmaster, Inc.
30800 Rancho Viejo Road
San Juan Capistrano, CA 92675
[phone] [phone]
www.fluidmaster.com
LEVER LE
BRAS EN
PREMIER