American Standard DXV Fresno D35403150 User manual

- 1 -
INSTALLATION INSTRUCTIONS
SAVE FOR FUTURE USE
M965557 Rev. 1.2
ROUGHING-IN DIMENSIONS:
• For reference
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2013
RECOMMENDED TOOLS AND MATERIALS
In the United States:
DXV by American Standard
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV by American Standard
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV by American Standard
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing,
supply stores. It is essential that the tools and materials be on hand before work is begun.
Fresno™ Single Control Kitchen
Faucet with Pull Out Spray
Model D35403150
Thank you for selecting DXV by American Standard.
To ensure that your installation proceeds smoothly,
please read these instructions carefully
before you begin.
Plumbers' Putty or CaulkingChannel Locks
Phillips Screwdriver
Flat Blade Screwdriver Adjustable Wrench
12-3/4"
(324mm)
28-3/4"
(733mm)
15-3/4"
(400mm)
10-1/4"
(262mm)
8-1/2"
(217mm)
6"
(154mm)
1-3/8" to 1-1/2"
(33 to 38mm)
DIA. MOUNTING HOLE
2"
(51mm)
60 mm
(2-3/8")
49 mm
(1-7/8")

- 2 -
1
3
2
5
7
6
8
9
10
11
RECESS
4
M965557 Rev. 1.2
1CAUTION INSTALL FITTING Turn off hot and cold water supplies before beginning.
• Make certain the O-RING SEAL (1) is properly seated in recess of faucet body.
• Insert supply HOSES (2), SHANK (3) and SPRAY HOSE (4) through center
hole of sink or mounting surface.
• Assemble RUBBER WASHER (5), PLASTIC WASHER (6), RUBBER & METAL “C”
WASHERS (7) and long LOCKNUT (8) onto SHANK (3) from underside of sink.
Hand tighten LOCKNUT (8) and check that faucet is centered.
• Tighten LOCKNUT (8) with wrench.
• Feed HOSE END (9) through HOSE GUIDE (10). Slide other side of HOSE GUIDE (10)
onto SHANK (3) and secure with LOCK NUT (11). Do not over tighten!
MAKE WATER SUPPLY CONNECTIONS
• Turn off hot and cold
water supplies before beginning.
• Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on tting supplies are 3/8" (10mm) compression. Connect left
supply (Marked with a Red Stripe) to Hot and right supply (Marked with Blue Stripe)
to Cold wall supply. Use adjustable wrench to tighten connections. Do not over tighten.
• Faucet supplies are 27-1/2" (699mm) long from faucet base.
• Note: If additional supply length is required, installer must purchase
additional parts separately.
• Important: If SUPPLY HOSES (1, 2) are too long, loop as illustrated to avoid kinking.
RED
STRIPE
BLUE
STRIPE
1
2
COLD
HOT
Figure 2
SEAL
WASHER
SEAL
WASHER
2
1
3
5 7
64
Figure 1
18" (457mm)
UNDER SIDE
OF MOUNTING
SURFACE
CONNECT HOSE SPRAY and INSTALL WEIGHT
• Check that seal washers are installed in
both ends of SPRAY HOSE ADAPTER (1).
Thread SPRAY HOSE ADAPTER (1) onto
faucet SHANK (2). Tighten with
adjustable wrench. Figure 1.
• Thread HOSE END (3) into bottom of
SPRAY HOSE ADAPTER (1). Tighten
with adjustable wrench. Make sure
all connections are tight. Figure 1.
• Install RUBBER BUSHING (4) onto
SPRAY HOSE (5). Install WEIGHTS
(6) onto HOSE (5) using two
screws (7). Locate WEIGHTS (6)
18"(457mm) from underside of mounting
surface on HOSE (5). Tighten
SCREWS (5) rmly.Figure 2.
2
3

- 3 -
M965557 Rev. 1.2
TEST INSTALLED FAUCET
• Unthread SPRAY HOSE (3) from SPRAY (2).
• Turn on water supplies and check connections for leaks.
• Hold HOSE END (3) in sink and operate HANDLE (1) on and off,
hot and cold to ush water lines thoroughly. Replace SPRAY (2).
• Pull SPRAY (2) out and check hose and supply connections
for leaks. Check that SPRAY HOSE (3) and WEIGHT (4) slide
up and down freely and do not interfear with supplies or waste
outlet plumbing. With faucet on turn SPRAY TOP (5) to spray
and aerator fuctions.
• Check all drain connections for leaks.
• Move HANDLE (1) to "off" position.
• Move HANDLE (1) into "off" position.
1
2
5
3
3
4
HOT & COLD SUPPLIES
5
• Loosen and remove LEVER HANDLE (1). Loosen HANDLE SCREW (2)
with 2.5mm Hex Wrench and then pull HANDLE BASE (3) off.
• Unthread ESCUTCHEON CAP (4). Unthread the CARTRIDGE NUT (5).
• Remove CARTRIDGE (6). Clean inlets of CARTRIDGE (6) and MANIFOLD (7).
• Reassemble CARTRIDGE (6). Replace CARTRIDGE NUT (5), CAP (4)
and HANDLE assembly, check ow.
• Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, rst turn off water supply then:
• If SPOUT (11) leaks at swivel point the O-RINGS (12) need
to be replaced. To remove SPOUT (11):
• Disconnect SPRAY HOSE (8) from CONNECTING NUT (9).
• Loosen the SPOUT SET SCREW (10) with a 3mm Hex wrench.
• Rotate the SPOUT (11) side to side while pulling upward to remove
SPOUT (11) from faucet body. Remove SPRAY HOSE (8).
• Replace the defective parts and grease O-RINGS (12). Replace SPRAY
HOSE (8). Push SPOUT (11) back into position. Tighten SET SCREW (10).
Reconnect SPRAY HOSE (8) to CONNECTING NUT (9).
• Check that SPOUT (11) rotates freely and does not leak at the swivel point.
9
8
11 3mm
HEX WRENCH
12
1
2
3
4
5
6
CLEAN
7
REMOVE
INSTALL
10
5SERVICE

- 4 -
M965557 Rev. 1.2
Single Control Kitchen
Faucet with Pull Out Spray
Fresno™
MODEL NUMBER
D35403150
M962648-0070A
SPOUT BUSHING
& O-RING KIT M962690-0070A
CARTRIDGE NUT
M962691-YYY0A
CARTRIDGE COVER
M964406-0070A
CARTRIDGE
M964722-YYY0A
HANDLE KIT
M962659-0070A
MOUNTING KIT
M962660-0070A
HOSE GUIDE
M962650-0070A
HOSE WEIGHTS
M962661-0070A
NUT
M962662-0070A
SPRAY HOSE ADAPTER
M962759-YYY0A
SPRAY HOSE
AND SEALS
M964725-YYY0A
PEDESTAL
M964731-YYY0A
PULL-OUT SPRAY
WITH CHECK VALVE
M962652-0070A
SPOUT SET SCREW
M964730-YYY0A
SPOUT ASSEMBLY 100
355
Replace the "YYY" with
appropriate nish code
POLISHED CHROME
ULTRA STEEL