American Standard Avery 4901.300 User manual

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2018
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
1
M965801 Rev.1.2 (11/18)
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
AVERY™
PULL-DOWN
KITCHEN & BAR FAUCET
INSTALLATION
INSTRUCTIONS
4901.300
4901.410
Flat Blade Screwdriver Adjustable Wrench Plumbers’ Putty or CaulkingPhillips Screwdriver
Certied to comply with ANSI A112.18.1M
B (OPTIONAL)
A
SPOUT BASE
SINK OR
MOUNTING
SURFACE
SPOUT BASE
3
7
9
8
2
10
5
3
6
7
9
4
4
8
1
10
12
5
6
11
13
CAUTION Turn off water at
main supply
(A) Installation less DECK ESCUTCHEON
• Make certain the SEAL (10) is properly seated in bottom recess of the SPOUT (2). Insert supply HOSES (3), SPRAY HOSE (4)
and SHANK (5) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.
• Insert HOSES (3) through RUBBER WASHER (6), BRASS WASHER (7), and threaded LOCKNUT (8).
• Assemble RUBBER WASHER (6), BRASS WASHER (7), and threaded LOCKNUT (8) onto SHANK (5) from underside
of sink or mounting surface. Hand tighten LOCKNUT (8).
• Use a screwdriver to tighten SCREWS (9) on LOCKNUT (8). Work your way around LOCKNUT (8), tightening the screws
slightly each time until all are snug to ensure even pressure.
(B) Installation with DECK ESCUTCHEON (optional)
• Make certain the SEAL (10) is properly seated in top recess of DECK ESCUTCHEON (1) and SEAL (12) is properly seated
in bottom recess of DECK ESCUTCHEON (1). Do not use putty.
• Screw in two THREAD RODS (13) onto bottom of DECK ESCUTCHEON (1).
• Insert SUPPLY HOSES (3), SPRAY HOSE (4) and SHANK (5) through hole of DECK
ESCUTCHEON (1), and mounting surface.
• Follow mounting instructions above
to secure faucet to mounting surface.
Thread the MOUNTING NUTS (11) to
secure DECK ESCUTCHEON.

- 2 -
2
M965801 Rev.1.2 (11/18)
3CONNECT SPRAY HOSE AND INSTALL WEIGHTS
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLY HOSES (1, 2) directly to wall
supplies. Connection on tting supplies are 3/8"
compression. Connect left supply hose (Red Stripe) to Hot
wall supply. Connect right supply hose (Blue Stripe) to Cold
wall supply. Use adjustable wrench to tighten connections.
Do not over tighten.
*Faucet supplies are 35"long from faucet base.
• Note: If additional supply length is required, installer
must purchase additional parts separately.
• Important: If SUPPLY HOSES (1, 2) are too long,
loop as illustrated to avoid kinking.
MAKE WATER SUPPLY CONNECTIONS
IMPORTANT: Do not
use sealent on threads
1
2
COLD
HOT
7
6
8
2
1
3
4
5
18"
• Push the SPRAY HOSE END (1) into the HOSE
CONNECTOR (2) and slide down the LOCKING
COLLAR (3) until it snaps into place.
• With HAND SPRAY (4) seated in SPOUT (5), install
WEIGHT (6) at labeled area onto HOSE (7), secure
with SCREW (8).

- 3 -
4
M965801 Rev.1.2 (11/18)
CHECK
CONNECTIONS
FOR LEAKS
1
REMOVE
2
3
• Move HANDLE (1) into “off” position.
• Turn on water supplies and check connections for leaks.
• With HANDLE (1) in “off” position, unthread SPRAY (3)
from HOSE (2).
• Operate HANDLE (2) up and down, left and right to ush
water lines thoroughly.
• Replace SPRAY (3) onto HOSE (2).
• Operate HAND SPRAY and check connections for leaks.
TEST INSTALLED FAUCET & CHECK CONNECTION FOR LEAKS
5
STREAM (AERATOR)
SPRAY
5
3
4
SPRAY OPERATION
• With FAUCET on, press TOGGLE BUTTON (4) on SPRAY (3) to switch
from stream to spray.
• Press and hold PAUSE BUTTON (5) to temporarily stop ow from SPRAY
(3). Release PAUSE BUTTON (5) to resume ow from SPRAY (3).

6
7
If Faucet Drips, Proceed As Follows:
• Turn VALVE to OFF position.
• Operate HANDLE several times from OFF to ON position. Do not apply excessive force.
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, rst turn off water supply then:
• Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).
• Unthread ESCUTCHEON CAP (4). Unthread three MOUNTING SCREWS (5).
• Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE SEALS (8).
• Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).
• Place SEALS (8) into CARTRIDGE PORTS (6a).
• Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING SCREWS (5) alternately.
• Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE SCREW (2) and install INDEX BUTTON (1).
DO: CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
SERVICE
CARE:
M965801 Rev.1.2 (11/18)
6
8
6a
7
1
2
4
5
3
- 4 -

- 5 -
M911793-0070A
Seal
1660152-XXX
Escutcheon & Putty Plate
FOR 4901.300
M962146-0070A
Mounting Kit
M951483-0070A
Cartridge
M918511-0070A
Cartridge Screws
M907315-YYY0A
Escutcheon Cap
M970376-YYY0A
Button & Screw Kit
M970266-YYY0A
Handle Kit
M950415-0070A
Spray With Hose
M950413-YYY150A
Spray Assembly
4901.300
2064101P-XXX
Escutcheon & Putty Plate
FOR 4901.410
M970267-YYY0A
Spray Assembly
4901.410
M922909-0070A
Aerator
M970094-0070A
Weight (4901.410)
M970249-0070A
Weight (4901.300)
M965801 Rev.1.2 (11/18)
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 002
STAINLESS STEEL 075
MODEL NUMBER
AVERY™
PULL-DOWN
KITCHEN & BAR FAUCET
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
4901.300
4901.410