American Standard Hampton 4751.732F15 User manual

KITCHEN FAUCETS
4751.732
4751.732F15
M968721 REV. 1.4
Certified to comply with ASME A112.18.1M
Plumbers' Putty or Caulking
Adjustable Wrench
Channel Locks
RECOMMENDED TOOLS
1
2
INSTALL FAUCET
INSTALL VALVE BODIES
Install LOCK NUT (1) and RUBBER WASHER (2) onto SPOUT BODY (3).
Insert SPOUT BODY (1) through hole from underside of SINK.
From under sink tighten LOCK NUT (1) to secure SPOUT.
Place RUBBER RING (4) into SPOUT ESCUTCHEON (5) and screw
ESCUTCHEON (5) onto SPOUT BODY (3) until snug against
internal stop.
Install LOCK NUT (1) and RUBBER WASHER (2) onto VALVE BODIES (3).
Insert VALVE BODY (3) through hole from underside of SINK.
From under sink tighten LOCK NUT (1) to secure VALVE BODY (3).
Insert SEAL WASHERS (6) into SPOUT BODY SUPPLY HOSES (7) and
tighten connection to VALVE BODIES (3).
Place RUBBER RING (4) into ESCUTCHEON (5) and screw
ESCUTCHEON (5) onto VALVE BODY (3) until snug against internal stop.
4
5
2
1
3
2
1
3
4
5
7
6
Phillips Screwdriver
Flat Blade Screwdriver
Installation
Instructions
CAUTION Turn off hot and cold water
supplies before beginning.
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
®

4
M968721 REV. 1.4
3INSTALL HANDLES
Push ADAPTER (2) into HANDLE BASE (3) in a way that the male square on the ADAPTER (2)
fits in the female 8 point star of the HANDLE (4).
Turn HANDLE STEM (1) to the off position. Push HANDLE BASE (3), ADAPTER (2) and
HANDLE (4) onto VALVE STEM (1).
Tighten HANDLE SCREW (5).
Push INDEX CAP (6) in top of HANDLE (4).
Push ADAPTER (2) into LEVER HANDLE BASE (7) in a way that the male square on the
ADAPTER (2) fits in the female star of the HANDLE BASE (7).
Turn HANDLE STEM (1) to the off position. Push LEVER HANDLE BASE (7) and
ADAPTER (2) onto VALVE STEM (1).
Tighten HANDLE SCREW (6).
Check alignment, if not satisfactory aligned;
Push out ADAPTER (2) carefully.
Turn ADAPTER (2) either 45˚ or 90˚ so that male square on ADAPTER (2) catches different female square in LEVER HANDLE BASE (7).
Assemble and tighten HANDLE SCREW (6). Push INDEX CAP (8) in top of LEVER HANDLE BASE (7).
CROSS HANDLE
LEVER HANDLE
1
3
4
FERRULE
COUPLING NUT
MAKE WATER SUPPLY CONNECTIONS
Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE SUPPLIES (3)
or 3/8"O.D. BULL-NOSE RISERS (4). Use adjustable wrench to
tighten connections. Do not over tighten. Be careful not to kink copper
supply when bending. Use tubing cutter to cut to proper length.
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE PURCHASED SEPARATELY.
CROSS HANDLES LEVER HANDLES
22
44
5
5
668
6
1
37

5
6
TEST INSTALLED FAUCET
FITTING WITH SPRAY
7
Remove AERATOR. With handles in OFF position, turn on water supplies and check all connections for leaks.
Operate both HANDLES to flush water lines thoroughly. Rotate SPOUT in both directions. Replace AERATOR.
M968721 REV. 1.4
Place SPRAY HOLDER (1) into separate hole of SINK (2) and
assemble NUT (3) onto shank from underside of SINK (2).
Feed SPRAY HOSE (1) through SPRAY HOLDER (2) and
attach COUPLING NUT (3) of HOSE (1) to HOSE ADAPTOR (4)
on valve body. Tighten COUPLING NUT (3) firmly.
FITTING WITH SPRAY
Hand tighten NUT (3).
1
2
1
3
2
Direct SPRAY HEAD into sink and activate SPRAY. Check HOSE connections for leaks.
3
4
8
Aerator may accumulate dirt causing distorted and reduced water flow. Remove aerator and rinse clean.
If spout drips, operate handles several times from OFF to ON position. Do not force-handles turn only 90˚.
If faucet drips proceed as follows:
9
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:

M968721 REV. 1.4
028610-0070A
VALVE
066070-YYY0A
(2.2 GPM) AERATOR
M922881-YYY0A
(1.5 GPM) AERATOR
013311-YYY0A
INDEX BUTTON
021470-YYY0A
INDEX BUTTON 021470-YYY0A
INDEX BUTTON
918428-0070A
HANDLE SCREW
918428-0070A
HANDLE SCREW
A952026-0070A
DIVERTER M953040-YYY0A
SPRAY HOLDER
M953668-YYY0A
HANDSPRAY & HOSE
060469-YYY220A (2.2 GPM)
SPOUT
060469-YYY150A (1.5 GPM)
SPOUT
073542-0070A
SPOUT O-RING
024220-0070A
SUPPLY NUT
042692-0070A
PORCELAIN CROSS
HANDLE
908501-YYY0A
HANDLE BASE
916503-YYY0A
HANDLE BASE
013307-YYY0A
CROSS HANDLE
M961633-YYY0A
SPOUT ESCUTCHEON
013312-YYY0A
VALVE ESCUTCHEON KIT
030258-0070A
VALVE MOUNTING KIT
M961635-0070A
HOSE & SEAL KIT
921767-0070A
COUPLING
923002-0070A
HANDLE ADAPTER
060354-YYY0A
METAL LEVER HANDLE
060353-YYY0A
PORCELAIN LEVER HANDLE
923012-0070A
CLIP
KITCHEN FAUCETS
MODEL NUMBERS
WRENCH
030258-0070A
SPOUT MOUNTING KIT
012470-YYY0A
END CAP
Replace the "YYY" with
appropriate finish code
923002-0070A
HANDLE ADAPTER
4751.732
4751.732F15
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
HOT LINE FOR HELP
002
295
224
CHROME
SATIN NICKEL
OIL RUBBED BRONZE
®