American Standard Monterrey 6500 User manual

SPREAD LAVATORY
FAUCETS
Installation
Instructions
6500
6502
6530
6532
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1
1
GOOSE NECK
SPOUT (POP-UP)
CONVENTIONAL SPOUT
Insert SPOUT SHANK (1, 1a) through
center hole of SINK, making sure
RUBBER GASKET (2, 2a) is properly positioned.
CONVENTIONAL OR GN SPOUT ASSEMBLY
Assemble RUBBER WASHER (3),
RETAINER (4) and LOCKNUT (5) onto
threads of SPOUT SHANK (1, 1a) from
underside of SINK.
Align SPOUT and tighten LOCKNUT (5).
Be sure slot in BRASS WASHER (4) is
positioned to the rear as shown.
Turn off water at
main supply.
CAUTION
SINK
SLOT
SINK
SLOT
GOOSE NECK
SPOUT
10
3
5
5/16'' MIN. MOUNTING SURFACE
11
11
1
2
3
1
2
1
3
4
53
4
5
2
2a
2
Push TUBING (4) ends into VALVE (5) side outlets. Insert VALVES (5)
into mounting holes from underside of ledge.
Install LOCKNUTS (1), BRASS WASHERS (2) and RUBBER WASHERS (3) onto valve shanks.
Place RUBBER RING (11) into DECK ADAPTERS (10) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) to secure VALVE (5) position.
Slide FERRULE (13) and COUPLING NUT (14) to outlet of VALVE (5) and tighten
COUPLING NUT (14) firmly.
Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
VALVE ASSEMBLY WITH RIGID VALVE CONNECTIONS
HOT
COLD
13
5
14
8
7
9
6
14
13
4
5
10
MOUNTING
LEDGE
11
10
Press TEE (6) onto SPOUT SHANK (7) making certain that the O-RING (8) is
properly seated on SHANK (7). Push COUPLING (9) into TEE (6) and
attach to SPOUT SHANK (7) and tighten.
1a
60186 REV.1.7 (11/15)

3
Apply a bead of PUTTY around underside of DRAIN FLANGE (1) flange.
Insert DRAIN PLUG (2) into SINK drain hole.
Hold DRAIN PLUG (2) to prevent turning and assemble GASKET (3), WASHER (4),
and LOCKNUT (5) from underneath sink.
Apply sealant to threaded end of TAILPIECE and thread into lower end of DRAIN PLUG.
Connect other end to trap.
DRAIN ASSEMBLY (6542.140/.170)
60186 REV.1.7 (11/15)
2a
Connect HOT water supply to inlet of left SHANK and COLD
water supply to right SHANK.
Press TEE (8) onto SPOUT SHANK (5) making certain that the O-RING (9)
is properly seated on SPOUT SHANK (5). Push COUPLING (4) into TEE (8)
and attach to SPOUT SHANK (5) and tighten.
Thread HOSE CONNECTOR (6, 6A) to VALVE CONNECTIONS (7, 7A).
Connect water supply to VALVE BODIES (1,1A) with 1/2" IPS FLEXIBLE
SUPPLIES (2) (not included. Use adjustable wrench to tighten connections.
Do not over tighten.
VALVE ASSEMBLY WITH FLEXIBLE HOSE VALVE CONNECTIONS
HOT
COLD FERRULE
COMPRESSION
NUT
COUPLING
NUT
FLEXIBLE
SUPPLIES
1
1A
3/8 O.D.
BULL-NOSE
RISERS
1/2" PIPE
THREAD
3/8 COMPRESSION
CONNECTION
2
3
4
5
7
6
6A 7A
9
8
PUTTY
SINK
1
2
3
4
5
2

TEST INSTALLED FAUCET
5
Remove AERATOR.
Turn VALVES (1) to off position.
Insert ADAPTOR (8) with larger diameter over the VALVE STEM (4).
Align LEVER (2) or WRIST BLADE HANDLE (3) and install onto VALVE STEM (4).
Insert BLUE INDEX (5) into cold valve (right side) and red INDEX (6) into
hot valve (left side).
Insert HANDLE SCREW (7) into HANDLES and tighten with screwdriver.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
Operate both handles to flush water lines thoroughly. Check
spout mounting and TEE connections for leaks.
Turn handles into OFF position and replace AERATOR.
INSTALL HANDLES
4
SERVICE
6
To change direction of handle rotation, proceed as follows:
Turn valve to OFF position.
Remove HANDLE and BONNET NUT.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90° and replace.
Replace SPRING CLIP.
Replace BONNET NUT, HANDLE, SCREW, and INDEX.
AERATOR may accumulate dirt causing distorted and reduced water flow.
Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON position.
Do not force - handles turn only 90°.
Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow.
To clean, first turn off hot and cold water supplies, then:
Remove HANDLE and BONNET NUT.
Remove CARTRIDGE by pulling up.
Thoroughly rinse plastic SCREEN at base of CARTRIDGE.
Replace CARTRIDGE until flange is tight against valve body.
Turn valves OFF.
Replace BONNET NUT, HANDLE, SCREW and INDEX.
SPRING
CLIP
STOP
WASHER
90°
CARTRIDGE
SCREEN
4
1
2
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
3
5
7
6
7
AERATOR
60186 REV.1.7 (11/15)
8

912711-0070A
O-RING
024220-0070A
COUPLING NUT
030256-0070A
SPOUT MOUNTING KIT
033757-0070A
TEE MOUNTING KIT
012111-0070A
TUBE & TEE KIT (8" CENTERS)
066064-0070A
TUBE & TEE KIT (12" CENTERS)
012112-0070A
TUBE SEAL &
COUPLING KIT
051210-0020A
LEVER HANDLE
951764-0070A
CARTRIDGE
051212-0020A
ESCUTCHEON KIT
051213-0070A
VALVEMOUNTING
KIT
028757-0070A
SPOUT GASKET
904939-0020A
BONNET NUT
051217-0020A
WRIST BLADE
HANDLE
051211-0070A
INDEX KIT
912711-0070A
O-RING
030256-0070A
SPOUT
MOUNTING KIT
A911748-0020A
SPOUT GASKET
051322-0020A
VANDAL PROOF SCREW
000690-0020A
HANDLE SCREW
066116-YYY0A
DRAIN STOPPER
TAILPIECE INSERT
066117-YYY0A
FLANGE KIT
070847-0070A
CLIP
066118-0070A
PIVOT ROD
900864-0070A
DRAIN BODY
066497-0020A
COMPLETE
DRAIN BODY
070532-0070A
TAILPIECE
SPREAD LAVATORY
FAUCETS
MODEL NUMBERS
015025-YYY0A
DRAIN COMPLETE
070532-0040A
TAILPIECE
000690-0020A
HANDLE SCREW
051211-0070A
INDEX KIT (PAIR)
6500
6502
6530
6532
60186 REV.1.7 (11/15)
066074-0070A
VR AERATOR, 0.5gpm
M922858-0020A
VR AERATOR, 0.35gpm
M964481-0070A
AERATOR 1.2 GPM
066508-0020A
AERATOR 0.5VR GPM
M922286-0020A
AERATOR 0.35 GPM
M918014-0070A
ADAPTER
M918014-0070A
ADAPTER
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are
trademarks of AS America, Inc.
© AS America, Inc. 2015
033757-0070A
TEE MOUNTING KIT
M970033-0070A
FLEXIBLE HOSE &
TEE KIT
072574-0070A
EXTENSION ROD
FOR PRODUCTS SOLD BEFORE 1/1/16
028617-0020A
POP-UP ROD
M970041-0020A
SPOUT
M970039-0020A
SPOUT
CHROME 002
Appropriate finish code