American Standard LAKELAND 4114.001 User manual

SINGLE CONTROL KITCHEN
FAUCET WITH CAST SPOUT
Installation
Instructions
Certified to comply with ANSI A112.18.1M
4114.001
4114.001F15
1
3
7
AB
CAUTION
1INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
Turn off hot and cold water
supplies before beginning.
PUTTY
S P O U T BA S E
S I NK OR
MOUNTING
SURFACE
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Recommended tools
2
3
7
Regular Screwdriver
2
LAKELAND®
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
(A) Installation with ESCUTCHEON (1).Apply a bead of puttyto bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Insert supply HOSES (2)and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface.
Follow mounting instructions below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1).Discard ESCUTCHEON with PUTTY PLATE (1). Insert supply HOSES (2) and
SHANK (3) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.
4
5
6
8
4
5
6
8
M968469 REV. 1. 6
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.

On model with separate spray, place the SPRAY HOLDER (1)
into the appropriate mounting hole. Assemble the SPRAY
HOLDER WING NUT (2) onto the shank of SPRAY HOLDER (1)
from below and hand tighten. Do not use putty.
On model with spray through the ESCUTCHEON (3), place
SPRAY HOLDER (4) into the hole of ESCUTCHEON (3). Assemble
SPRAY HOLDER NUT (5) onto the shank of SPRAY HOLDER (4)
from below and hand tighten. Do not use putty.
For installation less spray, cap off SPRAY HOSE
CONNECTION (9) with PIPE CAP (6).
3INSTALL SPRAY HOLDER
1
1
3
2
7
3
5
6
42
TEST INSTALLED FAUCET
Move HANDLE down into "off" position and remove
AERATOR (1).
Turn on water supplies and check connections for leaks.
Operate HANDLE (2) up and down, left and right to flush
water lines thoroughly.
For faucet with spray, direct SPRAY HEAD (3) into sink and
activate SPRAY (3). Check hose connections for leaks.
Move HANDLE (2) down to "off" position and replace AERATOR (1).
CHECK CONNECTIONS
FOR LEAKS
8
9
4
CONNECT HOSE SPRAY
Feed SPRAY HOSE (7) through SPRAY
HOLDER (1) and attach COUPLING NUT (8)
of HOSE (7) to SPRAY HOSE CONNECTION (9)
on valve body. Tighten COUPLING NUT (8)
firmly.
2
SPRAY HOSE
CONNECTION
MAKE WATER SUPPLY CONNECTIONS
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply to Hot (Marked with a Red Line)
and right supply to Cold wall supply. Use
adjustable wrench to tighten connections.
Do not over tighten.
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is
required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
M968469 REV. 1.6
1
2
COLD
HOT

M968469 REV. 1.6
Spout leakage. If fitting leaks above or below SPOUT HUB remove SPOUT as follows
and check SPOUT O-RINGS. First turn off water supply.
Remove HANDLE BUTTON (2) and loosen SET SCREW (1) with 2.5mm HEX
WRENCH (11) supplied. Pull HANDLE (3) off valve stem.
Pull off CAP (4). Loosen CARTRIDGE SCREWS (5) and remove CARTRIDGE (6).
Remove SPOUT (7) by pulling up gently while moving SPOUT (7) side to side.
Check both SPOUT O-RINGS (8) for damage. Replace if necessary.
On models with SPRAYS, DIVERTER (9) can be cleaned by pulling
DIVERTER (9) out of the MANIFOLD (10). Rinse clean the DIVERTER (9)
and MANIFOLD (10). Push DIVERTER (9) back into MANIFOLD (10).
Reverse procedure to reinstall SPOUT, CARTRIDGE and HANDLE.
Remove PLUG BUTTON (2), loosen HANDLE SCREW (1) and
remove HANDLE (3).
Remove ESCUTCHEON CAP (4). Unscrew the three CARTRIDGE
SCREWS (5). Clean MANIFOLD (10), CARTRIDGE (6) ports and
SEALS (13).
Clean inlets of CARTRIDGE (6) and MANIFOLD (10).
Reassemble CARTRIDGE (6), alternately tightening SCREWS (5).
Replace CAP (4) and HANDLE (3). Check flow.
SERVICE
5
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
Reduced flow. If the flow gradually reduces over a number of months, the AERATOR (12) may have collected debris.
To clean, remove AERATOR (12) and rinse with water and remove any debris. Turn on faucet to wash any debris
out of the faucet. Thread AERATOR (12) back into spout. Operate faucet.
6
3
1
2
11
8
10
7
4
5
6
13
12
9
SPOUT
HUB
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
PRY RED RING FORWARD
AND ROTATE COUNTER-
CLOCKWISE ONE CLICK
PRY RED RING FORWARD
AND ROTATE CLOCKWISE
"A"
ADJUSTMENT WHEN
WATER IS TOO HOT
"A"
"B"
ADJUSTMENT WHEN
WATER IS TOO COLD
"B"
By restricting handle rotation and limiting the amount
of hot water allowed to mix with the cold, the HOT LIMIT
SAFETY STOP reduces risk of accidental scalding. To
set the maximum hot water temperature of your faucets,
all you need to do is adjust the setting on the HOT LIMIT
SAFETY STOP.
Remove HANDLE BUTTON (2) and loosen SET SCREW (1).
Pull HANDLE (3) off valve stem. Pull off CAP (4). Use a flat
blade screwdriver or your fingers to pull up and rotate red
HOT LIMIT SAFETY STOP (5). Follow Step "A" or "B" to adjust
min./max. discharge temperature. "0" being the hottest
to "7" the coldest temperature setting.
HOT LIMIT SAFETY STOP
"RED RING"- HOT
LIMIT SAFETY STOP
0
1
2
3
4
5
6
3
1
24
5

MODEL NUMBERS
SINGLECONTROL KITCHEN
FAUCET WITH CAST SPOUT
M962298-0070A
SPACER AND SEAL
M907552-YYY0A
ESCUTCHEON
M962297-0070A
SPOUT SEAL KIT
(before 10/2012)
M964327-0070A
SPOUT SEAL KIT
(after 10/2012)
A951470-0070A
CARTRIDGE
M918506-0070A
CARTRIDGE SCREWS
M962339-YYY0A
ESCUTCHEON AND
PUTTY PLATE
M962340-YYY0A
ESCUTCHEON WITH SPRAY
HOLE AND PUTTY PLATE
042850-OO7OA
DIVERTER
M962146-0070A
MOUNTING KIT
066070-YYY0A (2.2 GPM)
AERATOR
M922881-YYY0A (1.5 GPM)
AERATOR
060341-0070A
PIPE CAP
CHROME
STAINLESS STEEL
OIL RUBBED BRONZE
002
075
224
Replace the "YYY" with
appropriate finish code
M962338-YYY0A
HANDLE KIT
A907086-YYY0A
ESCUTCHEON CAP
M962296-YYY22OA (2.2 GPM)
SPOUT KIT
M962296-YYY15OA (1.5 GPM)
SPOUT KIT
M962294-0070A
BUTTON AND
SCREW KIT
M961773-YYY0A
SPRAYHOLDER
(3-HOLE)
M953040-YYY0A
SPRAY HOLDER
M953667-YYY0A
HANDSPRAY & HOSE
LAKELAND®
M968469 REV. 1. 6
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-12-00
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
HOT LINE FOR HELP
4114.001
4114.001F15