American Standard Silhouette 7179.011 User manual

G25
© 2008 AS America Inc. Revised 2/08
SILHOUETTE™ 33" DUAL LEVEL KITCHEN SINK
• Americast® brand engineered material
• Dual level double bowl design
• Titanium enamel - heat resistant up to 1000°
• Acid-resisting glossy porcelain nish
• Tile edge installation
• Silicone sealant supplied
• Available in 1, 3, 4, or 5 faucet hole
conguration
• Customized hole punchings available
(see page G56)
Tile Edge:
❏ 7179.011 Center hole only
❏ 7179.813 3 hole
❏ 7179.814 4 hole
❏ 7179.815 5 hole
Nominal Dimensions:
838 x 559 x 241mm
(33" x 22" x 9-1/2")
Bowl sizes:
Right Hand: 191mm (7-1/2") wide
413mm (16-1/4") front to back
178mm (7") deep
Left Hand: 527mm (20-3/4") wide
476mm (18-3/4") front to back
229mm (9") deep
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.4M for Americast Plumbing Fixtures
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
SILHOUETTE™ 33"
DUAL LEVEL SINK
AMERICAST®
SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS
* See faucet section for available models
To Be Specied:
❏ Color:
❏ Faucet*:
❏ Faucet Finish:
❏ Basket Strainer: 4331.013
❏ Soap Dispenser: 4503.115, (specify color):
❏ Traps:
Optional Accessories:
❏ Large Wood Cutting Board: 9000.250
❏ Small Wood Cutting Board: 9000.185
❏ Colander for Cutting Board: 8102.100, Color:
❏ Large Colander: 8103.100, Color:
❏ Web Cover: 8106.100, Color:
❏ Bottom Sink Rack (Left): 7407.100, Color:

G26
© 2008 AS America Inc.
7179.813/814/815
NOTES:
* COUNTERTOP CUTOUT 806mm X 527mm WITH 25mm RADIUS
(31-3/4 X 20-3/4 WITH 1" RADIUS) AT CORNERS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
FINISHED WALL
OR SPLASHBACK
C/L
SEALING
COMPOUND
FINISHED
FLOOR
*CUTOUT
NOTE
7179.814
4 HOLE
1-1/2"O.D.
TAILPIECE
3/8"
(10mm)
7179.815
5 HOLE
TILED
COUNTERTOP
(BY OTHERS)
2-1/8"
(54mm)
1-1/2" (38mm)
DIA. HOLES TYP.
4"
(102mm)
4"
(102mm)
4"
(102mm)
4"
(102mm)
5/8"
(16mm)
2" (51mm)
OPTIONAL
7-7/8"
(200mm)
8-1/8"
(206mm)
3-1/2"
(89mm)
DIA.
9-3/4"
(248mm)
11-1/8"
(282mm)
16-1/2"
(419mm) 33"
(838mm)
22"
(559mm)
6"
(152mm)
5-3/4"
(146mm)
36" (914mm)
SUGGESTED
9-1/8"
(232mm)
5-3/4"
(146mm)
SILHOUETTE™ 33"
DUAL LEVEL SINK
AMERICAST®
Revised 2/08