American Standard Ultima 6147 Series User manual

1M965874 Rev. 1.1 (1/19)
© 2019 AS America Inc.
Installation Instructions
Ultima™Manual Flush Valve
Diaphragm-Type
Toilet Urinal
OPERATING PRESSURE:
25 psi (owing)-80 psi (static)
FLOW REQUIREMENT:
25 gpm (94.6 L/min.)
OPERATING PRESSURE:
20 psi (owing)-80 psi (static)
FLOW REQUIREMENT:
10 gpm (37.9 L/min.)
MODEL NUMBERS
6147 Series
6145 Series
NOTE TO INSTALLER: Please give this manual to the customer after installation.
To learn more about American Standard Selectronic®Products visit our website at: www.americanstandard-us.com
or e-mail us at: CR[email protected]
For Parts, Service, Warranty or other Assistance,
please call (844) CRT-TEAM / [phone] (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-306-1093)
Certied to comply with:
• ASSE 1037
• ANSI/ASME A112.19.2
• ADA Compliant

2M965874 Rev. 1.1 (1/19)
1. Flush Valve Assembly
2. Vacuum Breaker Assembly for Toilet
2a. Vacuum Breaker Assembly for Urinal
3. Spud Coupling Nut and Washers for Toilet
3a. Spud Coupling Nut and Washers for Urinal
4. Spud Flange for Toilet
4a. Spud Flange for Urinal
5. Sweat Solder Adapter
6. Cover Tube
7. Wall Escutcheon
8. Supply Stop
9. Installation Instruction
1
5
6
78
9
2
3
4
2a
3a
4a
!!! IMPORTANT !!!
WHEN MOUNTED ON AN ADA ACCESSIBLE
BOWL, THE ROUGH-IN TO THE SUPPLY INLET
SHOULD BE NO HIGHER THAN 37-1/2” OR THE
HANDLE WILL EXCEED MAXIMUM HEIGHT
ALLOWANCES UNDER ADA GUIDELINES.
M965874 Rev. 1.1 (1/19)
© 2018 AS America Inc .
Installation Instructions
Certied to comply with:
• ASSE 1037
• ANSI/ASME A112.19.2
• ADA Compliant
NOTETO INSTALLER: Please give this manual to the customer after installation.
To learn more aboutAmerican Standard Products visit our website at: www.americanstandard-us.com
or e-mail us at: [email protected]
For Parts, Service, Warranty or otherAssistance,
please call (844) CRT-TEAM / [phone] (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-306-1093)
MANUAL FLUSH VALVE
Toilet, Urinal & Clinic Sink with Manual
Operation Flushometer
Toilet Urinal
MODEL NUMBERS
6147 SERIES
6145 SERIES
OPERATING PRESSURE:
25 psi (owing)-80 psi (static)
FLOW REQUIREMENT:
25 gpm (94.6 L/min.)
OPERATING PRESSURE:
20 psi (owing)-80 psi (static)
FLOW REQUIREMENT:
10 gpm (37.9 L/min.)
Thank you for selecting American-Standard...the benchmark of ne quality for over 100 years.To ensure
that your installation proceeds smoothly--please read these instructions carefully before you begin.
Remove the Flush Valve items from the carton.The illustration below shows all items
after they have been removed from the carton. Some items may be packaged partially
assembled to other items.
UNPACKING All American Standard Products Are Water Tested At Our Factory.
Some Residual Water May Remain In The Valve During Shipping
CARE INSTRUCTIONS:
DO: CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.

3M965874 Rev. 1.1 (1/19)
123
4
5
6
7
8
10'
1. Flush Valve Assembly
2. Vacuum Breaker Assembly for Toilet
2a. Vacuum Breaker Assembly for Urinal
3. Spud Coupling Nut and Washers for Toilet
3a. Spud Coupling Nut and Washers for Urinal
4. Spud Flange for Toilet
4a. Spud Flange for Urinal
5. Sweat Solder Adapter
6. Cover Tube
7. Wall Escutcheon
8. Supply Stop
9. Installation Instruction
*Note: The Critical Line (-C-L-) on Vacuum Breaker
must typically be 6"(152mm) minimum above fixture.
Consult Codes for details.
FOR 1-1/2" TOP
SPUD FIXTURES
-C-L-
*CRITICAL
LEVEL
SUPPLY
DN 25 mm
(1" I.P.S.) 108-133 mm
(4-1/4" to 5-1/4")
292 mm
(11-1/2")
6047.1x1
ROUGH-IN
DIMENSION
686 mm
(27")
6047.1x2
ROUGH-IN
DIMENSION
610 mm
(24")
6047.117
ROUGH-IN
DIMENSION
FINISHED WALL
6047.1x2
765 mm
(30-1/8")
6047.117
689 mm
(27-1/8")
6047.1x1
371 mm
(14-5/8")
38mm-127mm
(1-1/2-5")
Right or Left Hand Installation
152 mm
(6")
(Min.)
Roughing-in Dimensions
Fig.1
Fig.2
FINISHED WALL
FINISHED
FLOOR
57 mm Min.
(2-1/4")
371 mm
(14-5/8")
TYPICAL WATER CLOSET INSTALLATION:
AFWALL™TOILET SHOWN
295 mm
(11-1/2")
-C-L-
SEE ROUGH-IN
ABOVE
CRITICAL
LEVEL 108 mm, +/-13 mm
(4-3/4")(+/-1/2")
SUPPLY
DN 25 mm
(1" I.P.S.)
*Note: The Critical Line (-C-L-) on Vacuum Breaker
must typically be 6"(152mm) minimum above fixture.
Consult Codes for details.
Right or Left Hand Installation
-C-L-
152mm
(6)
(Min.)
*CRITICAL
LEVEL
SUPPLY
DN 19mm
(3/4" I.P.S.)
295mm
(11-1/2")
FINISHED WALL
371mm
(14-5/8")
38mm-127mm
(1-1/2-5")
-C-L-
FOR 3/4" TOP
SPUD URINAL
108-133 mm
(4-1/4" to 5-1/4")
FINISHED FLOOR
FINISHED WALL
371 mm
(14-5/8")
TYPICAL URINAL INSTALLATION: WASHBROOK URINAL SHOWN
295 mm
(11-1/2") SEE ROUGH-IN
ABOVE
CRITICAL
LEVEL
-C-L-
SUPPLY
DN 20 mm
(3/4" I.P.S.)
108-133 mm
(4-1/4" to 5-1/4")
-C-L-
57 mm Min.
(2-1/4")
Roughing-in Dimensions
Fig.2
RECOMMENDED TOOLS; Fig. 2
1. Teon Tape
2. Flat Blade Screwdriver (For adjusting Supply Stop)
3. Adjustable Wrench
4. Tape Measure
5. Hacksaw
6. Tubing Cutter
7. File

4M965874 Rev. 1.1 (1/19)
1
23
4
Fig. 5
5a
5a
1-1/2" TOP SPUD
CENTER LINE OF
FIXTURE SPUD
FINISHED WALL
FILE EDGES
SOLDER
ADAPTER
Fig.3 Fig.3a
ADAPTER
32mm
(1-1/4)
A
(A-B)= B
C
CLEAN
1
1
4
2
3
Fig. 4
TEFLON TAPE
FINISHED WALL
X
X
Fig. 4a
Fig. 4b
Fig. 4c
2
1INSTALL SWEAT SOLDER ADAPTER; Fig. 3
Note: Install Optional Sweat Solder Adapter (Supplied)
for copper pipe supply line. Fig. 3.
1. Measure the distance (A) from the nished wall to the
center of the inlet spud on the xture.
2. Cut the supply pipe 1-1/4"(A-B=C) shorter then the
measurement taken in Step 1. File any rough edges off the
end of the supply pipe.
3. Clean the end of the supply pipe. Push the threaded
Adapter on until it is seated against the internal stop.
Sweat the Adapter to the pipe.
2INSTALL COVER TUBE, WALL
ESCUTCHEON and SUPPLY STOP; Fig. 4
1. Measure from nished wall to rst thread of Adapter or
threaded supply pipe (dimension “X”). Cut COVER
TUBE (1) to length (X). Apply Teon Tape to the threaded
end of the Adapter or supply pipe. Fig. 4a.
2. Push the COVER TUBE (1) into the WALL
ESCUTCHEON (2). Slide both onto the SUPPLY PIPE (3).
Fig. 4b.
3. Push the COVER TUBE (1) in to expose the threads of the
supply pipe. Fig. 4c. With a wrench thread the SUPPLY
STOP (4) onto the SUPPLY PIPE (3). Align and tighten.
Fig. 4c.
4. Pull COVER TUBE (1) against SUPPLY STOP (4) and push
WALL ESCUTCHEON (2) against nished wall.
3INSTALL VACUUM BREAKER TUBE; Fig. 5
1. Place the SPUD FLANGE (1) over the spud on the Fixture.
2. Place FRICTION WASHER (3) and SEAL WASHER (4)
inside SPUD COUPLING NUT (2) and thread onto Spud.
Do not tighten fully.
3. Insert the VACUUM BREAKER TUBE (5) or (5a) into the
SPUD COUPLING NUT (2) and push it down.
Note: If cutting VACUUM BREAKER TUBE (5) to size, note
that Critical Line (C/L) on Vacuum Breaker must
typically be 6"(152mm) above xture. Consult Code
for details.
CAUTION Turn off hot and cold water
supplies before beginning.

5M965874 Rev. 1.1 (1/19)
3
25
1
4
Fig. 6a
7
9
6
2
5
8
121mm, 13mm
(4-3/4")( 1/2")
Fig. 6b +
–
+
–
Fig. 7
REMOVE COVER
2
1
CLOCKWISE
CLOSES CONTROL STOP
COUNTER-CLOCKWISE
OPENS CONTROL STOP
3
4
5
4INSTALL FLUSH VALVE; Fig. 6a & 6b
1. As shown in Fig. 6a, insert the TAILPIECE (1) on the
FLUSH VALVE (2) into the SUPPLY STOP (3). Lubricate
the INLET FLANGE O-RING (4) with water if necessary.
Lightly tighten COUPLING NUT (5). Fig. 6a.
Important: Do not use lubricants (other than water) or
any type of thread sealing paste or tape
2. Align the FLUSH VALVE (2) (Fig. 6b) directly above the
VACUUM BREAKER (7) and VACUUM BREAKER
COUPLING NUT (6).
Note:There is a ±13 mm, (±1/2") tolerance for the 121 mm
(4-3/4") dimension Fig. 6b.
3. Pull the VACUUM BREAKER COUPLING NUT (6) up
to meet the threaded FLUSH VALVE CONNECTION (8)
and hand tighten. Align all components of the ush valve
assembly. Fig. 6b.
4. Lightly tighten the COUPLING NUT (5) connection rst,
then the VACUUM BREAKER COUPLING NUT (6) and
nally the SPUD COUPLING NUT (9). Once alligned
correctly, use a wrench to tighten couplings to make water
tight connections. Fig. 6b.
5FLUSH OUT SUPPLY LINES Fig. 7
1. Make sure supply stop is closed. Remove COVER (1) from
SUPPLY STOP (2). With a at blade screwdriver close
CONTROL STOP (2).
2. Remove FLUSH VALVE CAP (3 & 4). Pull out
DIAPHRAGM ASSEMBLY (5). Replace FLUSH VALVE
CAP (3 & 4) and tighten.
3. With a at blade screwdriver open SUPPLY STOP (2).
to ush line of any debris or sediment.
4. Close SUPPLY STOP (2). Remove FLUSH VALVE
CAP (3 & 4). Replace DIAPHRAGM ASSEMBLY (5).
Replace FLUSH VALVE CAP (3 & 4) and tighten

6M965874 Rev. 1.1 (1/19)
6
ADJUST SUPPLY STOP; Fig. 13
IMPORTANT:To avoid overowing, the SUPPLY STOP (3)
must never be opened to the point where the ow from
the valve exceeds the ow capacity of the xture. Valve
is designed to provide stated ush volume with a 25 gpm
ow rate for toilet and 10 gpm ow rate for urinal.
1. Remove COVER (2) from SUPPLY STOP (3).Turn on water
supply 1/4 turn to 1/2 turn(CCW) and test for leaks.
Note: Unit may ush for approximately 5 to 10 sec. when
water is rst turned on.
2. Push down on HANDLE (4) to initiate ush.
3. Adjust SUPPLY STOP (3) after each ush until the stated
ush volume is achieved, no splashing occurs and the xture
is properly cleansed.
4. When adjustment is complete, reinstall COVER (2) and
tighten to ensure vandal-resistance.
7HOW TO RETROFIT OUR VALVE; Fig. 14
Replaces Industry Standard Manual and Electronic Valves)
Note: In most Retrots the wall escutcheon, supply
stop, cover tube and vacuum breaker do not have to be
replaced. If these items do need replacement they must
be purchased separately or order the complete ush valve
assembly from American Standard.
1. Remove COVER (1) from SUPPLY STOP (2) if installed.
Fig. 14.
2. Turn water supply off. Fig. 14.
3. Unthread COUPLING NUT (3) and VACUUM BREAKER
COUPLING NUT (4). Remove FLUSH VALVE (5). Fig. 4a.
4. Clean all threaded connections before installing the new
ush valve. Fig. 14a.
5. Refer to Sections 4, 5 and 6 to complete the retrot installation.
Fig. 14b.
8
LEFT OR RIGHT HAND INSTALLATION;
Fig. 15
1. The FLUSH VALVE can be installed either as a right or left
hand installation.
2. Orientate the FLUSH VALVE as shown in Fig. 13 to desired
position for a left or right hand installation.
Fig. 13
2
REMOVE COVER
CLOCKWISE CLOSES
CONTROL STOP
COUNTER-CLOCKWISE
OPENS CONTROL STOP
3
CLEAN
CONNECTIONS
2
Fig. 14 Fig. 14a Fig. 14b
1
3
4
5
Fig. 15
Right or Left Hand Installation
Left Hand Right Hand

M965874 Rev. 1.1 (1/19)
7
M952269-0020A
(6147 SERIES)
ESCUTCHEON KIT
M964411-0020A
(6147.111, 6174.121, 6147.161)
VACUUM BREAKER
ASSEMBLY 11-1/2"
(292 mm) ROUGH-IN
M954323-0070A
DIAPHRAGM ASSEMBLY 1.1 GPF
M954322-0070A
DIAPHRAGM ASSEMBLY 1.28 GPF
M954319-0070A
DIAPHRAGM ASSEMBLY 1.0/1.6 GPF
M909318-0070A
INSIDE COVER
M964402-0070A
VACUUM BREAKER
REPAIR KIT
M964413-0020A
(6147.122, 6147.162)
VACUUM BREAKER ASSEMBLY
27" (686 mm) ROUGH-IN
M954311-0020A
HANDLE ASSEMBLY
M970429-0070A
HANDLE REPAIR KIT
A955057-0020A
1" INLET PIPE ASSEMBLY
M964945-0020A
(4-1/4" to 5-1/4" Rough-in)
OPTIONAL ADJUSTABLE TAILPIECE
(Purchased Separately)
M962836-0020A
(8-1/4" to 9-1/4" Rough-in)
M962835-0020A
(7-1/4" to 8-1/4" Rough-in)
M962834-0020A
(6-1/4" to 7-1/4" Rough-in)
M962833-0020A
(5-1/4" to 6-1/4" Rough-in)
A955056-0020A
1" SUPPLY STOP
M924347-0020A
SUPPLY STOP CAP
M970355-0020A
STOP VALVE
REPAIR KIT
A912809-0070A
TAILPIECE O-RING
M962926-0070A
1" SWEAT ADAPTER
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
(844) CRT-TEAM / [phone]
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of AS America, Inc. ©2019
To learn more about American Standard Selectronic®Products visit our website at:
www.americanstandard-us.com or e-mail us at: [email protected]
MODEL NUMBER
6147 Series
Ultima™Manual Flush Valve
Diaphragm-Type

M965874 Rev. 1.1 (1/19)
8
M952262-0020A
(6145 SERIES)
ESCUTCHEON KIT
M964412-0020A
3/4" VACUUM BREAKER
ASSEMBLY
M964945-0020A
(4-1/4" to 5-1/4" Rough-in)
OPTIONAL ADJUSTABLE TAILPIECE
(Purchased Separately)
M962836-0020A
(8-1/4" to 9-1/4" Rough-in)
M962835-0020A
(7-1/4" to 8-1/4" Rough-in)
M962834-0020A
(6-1/4" to 7-1/4" Rough-in)
M962833-0020A
(5-1/4" to 6-1/4" Rough-in)
A912809-0070A
TAILPIECE O-RING
M964402-0070A
VACUUM BREAKER
REPAIR KIT
M952261-0020A
3/4" INLET PIPE ASSEMBLY
M955058-0020A
3/4" SUPPLY STOP
M924347-0020A
SUPPLY STOP CAP
M970355-0020A
STOP VALVE
REPAIR KIT
M954327-0070A
DIAPHRAGM ASSEMBLY 0.125 GPF
M954326-0070A
DIAPHRAGM ASSEMBLY 0.5 GPF
M954319-0070A
DIAPHRAGM ASSEMBLY 1.0/1.6 GPF
M970429-0070A
HANDLE REPAIR KIT
M909318-0070A
INSIDE COVER
M954311-0020A
HANDLE ASSEMBLY
M964075-0070A
3/4" SWEAT ADAPTER
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
(844) CRT-TEAM / [phone]
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of AS America, Inc. ©2019
To learn more about American Standard Selectronic®Products visit our website at:
www.americanstandard-us.com or e-mail us at: [email protected]
MODEL NUMBER
6145 Series
Ultima™Manual Flush Valve
Diaphragm-Type

1M965874 SP Rev. 1.1 (1/19)
© 2019 AS America Inc.
Instrucciones de Instalación
Válvula de Descarga
Manual Ultima™
Diafragma
Inodoro Mingitorio
PRESIÓN DE OPERACIÓN:
25 psi (uyendo) - 80 psi (estática)
REQUISITO DE FLUJO:
25 gpm (94.6 l/min.)
PRESIÓN DE OPERACIÓN:
20 psi (uyendo) - 80 psi (estática)
REQUISITO DE FLUJO:
10 gpm (37.9 l/min.)
NÚMEROS DE MODELO
Serie 6147
Serie 6145
NOTA PARA EL INSTALADOR: Entregue este manual al cliente después de la instalación.
Para obtener más información sobre los productos American Standard Selectronic®, visite nuestro sitio web:
www.americanstandard-us.com o envíenos un correo electrónico a: [e-mail]
Para refacciones, servicio, garantía u otra asistencia, por favor llame al
(844) CRT-TEAM / [phone] (en Canadá: 1-800-387-0369)
(En Toronto únicam ente: 1-905-306-1093)
Certicado para cumplir
con las normas:
• ASSE 1037
• ANSI/ASME A112.19.2
• ADA Compliant

2M965874 SP Rev. 1.1 (1/19)
1. Conjunto de la válvula de descarga
2. Conjunto de la válvula de contraujo para inodoro
2a. Conjunto de la válvula de contraujo para mingitorio
3. Tuerca y arandelas de acoplamiento del spud para inodoro
3a.Tuerca y arandelas de acoplamiento del spud para mingitorio
4. Brida del spud para inodoro
4a. Brida del spud para mingitorio
5. Adaptador de soldadura
6.Tubo de cubierta
7. Chapetón de pared
8. Cierre del suministro
9. Instrucciones de instalación
1
5
6
78
9
2
3
4
2a
3a
4a
¡IMPORTANTE!
SI SE MONTA EN UNA TAZA ACCESIBLE DE
ADA, LA PREPARACIÓN A LA ENTRADA DE
SUMINISTRO NO DEBE SUPERAR37-1/2” O
LA MANIJA EXCEDERÁ LA ALTURA MÁXIMA
PERMITIDA POR LAS DIRECTIVAS DE LA ADA.
M965874 SP Rev. 1.1 (1/19)
© 2018 AS America Inc .
Installation Instructions
Certied to comply with:
• ASSE 1037
• ANSI/ASME A112.19.2
• ADA Compliant
NOTETO INSTALLER: Please give this manual to the customer after installation.
To learn more aboutAmerican Standard Products visit our website at: www.americanstandard-us.com
or e-mail us at: [email protected]
For Parts, Service, Warranty or otherAssistance,
please call (844) CRT-TEAM / [phone] (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-306-1093)
MANUAL FLUSH VALVE
Toilet, Urinal & Clinic Sink with Manual
Operation Flushometer
Toilet Urinal
MODEL NUMBERS
6147 SERIES
6145 SERIES
OPERATING PRESSURE:
25 psi (owing)-80 psi (static)
FLOW REQUIREMENT:
25 gpm (94.6 L/min.)
OPERATING PRESSURE:
20 psi (owing)-80 psi (static)
FLOW REQUIREMENT:
10 gpm (37.9 L/min.)
Gracias por elegir American Standard...el referente de na calidad por más de 100 años. Para asegurarse
que su instalación proceda correctamente, por favor lea estas instrucciones antes de comenzar.
Remueva del cartón los componentes de la Válvula de Descarga. La ilustración
de abajo muestra todos los componentes una vez removidos de la caja. Algunos
componentes pueden estar empacados parcialmente ensamblados con otros.
DESEMBALAJE
Todos Los Productos De American Standard Son Probados Con
Agua En La Fábrica. Puede Haber Agua En La Llave Al Recibirla.
INSTRUCCIONES DE CUIDADO PARA LOS COMPONENTES CROMADOS:
DEBE: LAVAR EL PRODUCTO SÓLO CON AGUA LIMPIA. SECAR CON UN PAÑO SUAVE DE ALGODÓN.
NO DEBE: LIMPIAR EL PRODUCTO CON JABONES, ÁCIDO, PASTA, ABRASIVOS, LIMPIADORES DUROS NI
CON UN PAÑO DE SUPERFICIE GRUESA.