American Standard Town Square Classic Caddie 9371.335.XXX Instruction manual

730833-100
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2004
ASSEMBLY & INSTALLATION
INSTRUCTIONS
9378.335.XXX
9374.335.XXX
9371.335.XXX
TOWN SQUARE CLASSIC CADDIE
- 1 -
Recommended Tools & Materials
Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years.
To help insure that the installation process will proceed smoothly, please read these instructions carefully before you
begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.
Adjustable Wrench
Channel Locks
Regular Screwdriver
Phillips Screwdriver
Pipe Wrench
Putty Knife Drill
Level
Plumbers' Putty or
Caulking
Tape
Measure
0790.XXX TOWN SQUARE PEDESTAL SINK
9370.100.335 CLASSIC CADDIE
9-1/2"
(241mm)
20-1/4"
(514mm)
24"
(610mm)
FINISHED
WALL
1-3/4" DIA.
STD. DRAIN
OUTLET
18-3/4" (476mm) 2-5/8"
(67mm)
4"
(102mm)
3-3/4"
(95mm)
■
1-1/4" O.D.
WASTE
★ 20"
(508mm)★ 18"
(457mm)
SUPPLIES AS
REQUIRED
6"
(152mm)
1-1/4" O.D.
TAILPIECE
16-1/8"
(410mm) 14-1/8" (359mm) FINISHED
FLOOR
36"
(914mm)
28"
(711mm)
8"
(203mm)

730833-100
1
2
3
4
- 2 -
Note: If replacing an existing sink, shut off the water
supply before removing old sink. If installing in a new
bathroom, follow the rough-in diagram to locate the
rough supply and waste lines.
Provide suitable reinforcement behind finished wall for
sink hanger screws. For an installed sink height of
36", center the reinforcement 32" above the floor.
1) Move the caddie into approximate position near the wall.
2) Place the sink on the caddie.
3) Place the level on the sink. If adjustment is required, either front-to-back
or side-to-side, remove the sink, place one or more of the adhesive-
backed cushions on the top surfaces of the caddie, and replace the sink
to verify.
4) Move the assembly into contact with the wall.
5) With a pencil, mark through the center of the two mounting holes found
on the back of the sink. See VIEW "A".
6) Move the assembly away from the wall.
7) Drill two pilot holes at the center marks using a 1/4" bit. Bore in 1" deep.
8) Thread the two 5/16" headless hanger screws into the pilot holes leaving
1-7/8" thread exposed in front of the wall.
C/L of 2 x 8
Support
and Bracket
Finished
Floor
32"
BC
Connect the trap to drain assembly hand tight to check alignment. It may be
necessary to cut off part of the tailpiece (area "B") or part of the horizontal leg
of the trap (area "C").
Connect hot and cold supply lines between the fitting valve and the supply
shut-off valves. Tighten trap joints for watertight assembly. Apply a bead of
caulk around the back edge of the sink where it contacts the wall.
Tighten the sink securely against the wall.
SINK AND CADDIE INSTALLATION
Following the manufacturer's instructions, install faucet and
drain assembly (not included) in the sink. Apply a bead of
sealing putty on the underside of the drain to ensure a
watertight seal between the sink and the drain. Remove
excess putty immediately after tightening drain.
Move the assembly back toward the wall, guiding the sink
over the two headless hanger screws. Place washers over
studs and firmly hand-tighten nuts onto each. Hanger Screw,
Washer & Nut
Sink
With sink
in place mark
the two
mounting
hole locations.
VIEW "A"

730833-100
- 3 -
CARE INSTRUCTIONS: Rinse the product clean with clear water. Dry with a soft cotton flannel cloth.
DO NOT: Clean with soaps, acid, polish, abrasives, harsh cleaners, or a cloth with coarse surface.
AMERICAN STANDARD ONE-YEAR LIMITED WARRANTY
If inspection of this American Standard plumbing product, within one year after its initial purchase, confirms that it is
defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar
model.
This warranty does not apply to local building code compliance. Since local building codes vary considerably, the
purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before
installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to
faulty maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with American Standard's
instructions; or if it has been modified in a manner inconsistent with the product as shipped by American Standard.
American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs
of removal or installation, nor shall American Standard be responsible for any other incidental or consequential
damages attributable to a product defect or to the repair or exchange of a defective product, all of which are
expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied
warranties, so this exclusion may not apply to you.)
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province
to province, in which case this warranty does not affect such statutory rights.
AMERICAN-STANDARD WOOD FURNITURE WARRANTY
If inspection of this American-Standard plumbing product, within one year after its initial purchase, confirms that it is
defective in materials or workmanship, American-Standard will repair or, at its option, exchange the product for a similar
model. Variations in actual wood color and finishes which may result from natural characteristics of the wood, such as grain
patterns, mineral streaks and the like, are not defects and are not covered by this warranty.
This warranty applies only to the original purchaser and installation of these products.
This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the
purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before
installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to
faulty maintenance, abuse, misuse, accident or other damages; if it was not installed in accordance with American-Standard’s
instructions; or if it has been modified in a manner inconsistent with the product as shipped by American-Standard.
American-Standard’s option to repair or exchange the product under this warranty does not cover any labor or other costs
of removal or installation, nor shall American-Standard be responsible for any other incidental or consequential damages
attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from
this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may
not apply to you).
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or province to
province, in which case this warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom
the product was purchased, or that a service request (including a description of the product model and of the defect) be sent
to the following address:
In the United States:
American Standard Inc.
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States, warranty information may also be
obtained by calling the following toll free number: [phone]
In Canada:
American Standard
2480 Stanfield Rd.
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: [phone]
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
PART NO. PACKED QTY. DESCRIPTION
738802-2950A 1
2
1
Door Knob
Hinges
Door - less Knob
738803-0070A
738804-3350A
9370 CADDIE REPLACEMENT COMPONENTS LIST