American BARIBED 600 BOY User manual

861 Taylor Rd., Suite “I”
Columbus, Ohio 43230
www.ame-medical.com
Phone: [phone]
Fax: [phone]
[email protected]
PAGE 1
Bed BariBed 600BOY
The Baribed 600 BOY is the perfect fit in a Home or
clinical setting. This Bed Model is fully electric with a
750 lb weight capacity. As it is difficult for someone of
large proportions to feel secure and comfortable in a
standard size bed, Big Boyz has developed these beds
to provide stability and quality of life for the large size
person.
The Baribed 600 BOY bed features smooth and quiet
Linak™ motors which allow for dynamic movement
without disturbing a partner or surrounding residents.
The foot section does not pitch down, but plateaus to
reduce edema of lower extremities. All electronics are
completely enclosed, fully grounded with hospital grade
3 prong heavy duty plug and cord. Electronics and motors are UL listed, 115 volts. Remote features 6 button
control for all functions, is low voltage, and has a high impact resistant case. Optional bed mounted trapeze,
heavy duty side rails, and integrated digital scale are also available.
Key Product Features
ALL ELECTRIC
• Steel Pan Deck…For Proper Mattress
Support
• Easy Touch Hand Control 12 Volt
• Large Capacity/Extra Wide
• All Electronics And Motors Ul Ap-
proved
PATIENT CONTROL:
• 8 Button Control For All Functions
• Low Voltage
• Low Energy
• High Impact Resistant Case
ELECTRONICS:
• Electronics Completely Enclosed
• Fully Grounded, With Hospital Grade,
3 Prong, Heavy Duty Plug And Cord
• Electronics And Motor Ul Listed
• Voltage 115V
Cardio Chair
Position
Trendelenberg
Position

861 Taylor Rd., Suite “I”
Columbus, Ohio 43230
www.ame-medical.com
Phone: [phone]
Fax: [phone]
[email protected]
PAGE 2
REMOTE CONTROL AND SETTINGS
EMERGENCY EVACUATION PROCEDURE - For Bed Models w/Convertible Feature
• Pull off side Velcro bolsters
• Pull out cable extension pins
• slide bed deck extensions in towards center of bed
• Perform this procedure on right and left side of bed deck surface
• THE BED IS NOW 40 3/4” WIDE AND CAN BE USED AS AN EVACUTION
GURNEY WITH SIDE RAILS

861 Taylor Rd., Suite “I”
Columbus, Ohio 43230
www.ame-medical.com
Phone: [phone]
Fax: [phone]
[email protected]
IMPORTANT WARNINGS
PAGE 3
WARNNG: POSSIBLE INJURY:
• Before adjusting bed, check that nothing is under or near bed. Keep children
and pets away from the bed to prevent injury.
• Keep bed in lowest position except for providing care (bathing, clothing
changes, etc.) Entering or exiting a raised bed could result in falls or injury.
• Injury may result from improper use of bed accessory manufacturer for
proper use instructions.
WARNNG: POSSIBLE SHOCK HAZARD:
• Bed power cord has a hospital grade 3-prong grounding plug. Connect only
to a hospital grade 3-prong outlet. Do not defeat grounding safety feature
by using a 3-prong to 2-prong adapter. If necessary, have outlet ground
reliability checked by a qualified electrician.
• The motor control box does not contain serviceable parts. Unplug the bed if
there is a malfunction. Refer servicing to qualified personnel.
• Unplug power cord from wall outlet before performing any maintenance or
service to the power box.
• Unplug the power cord of electric beds before cleaning with water based
solutions.
WARNNG: MISCELLANEOUS:
• TOADVOIDPOSSIBLEINJURYORDEATH - use a mattress thick
enough and wide enough so that the gap between the top of the mattress
and the bottom of the side rail is small enough to prevent a patient from
getting their head between the mattress and the side rail and possible
suffocating.
• CASTORLOCKSINCREASEBEDSTABILITY and resident safety,
decreasing the liability of a nursing home.
• POSSIBLEFIREHAZARD - Pendant must be attached at the foot end of
the bed when using oxygen-administered equipment

861 Taylor Rd., Suite “I”
Columbus, Ohio 43230
www.ame-medical.com
Phone: [phone]
Fax: [phone]
[email protected]
CLEANING RECOMMENDATIONS
ROUTINE CARE:
• Do not use harsh cleaners or solvents.
• Follow all manufacturer directions for dilution of concentrated cleaning agents.
• Wipe fabric clean with neutral soap suds and lukewarm water. rinse thoroughly
and allow drying before return to service.
• Hard to clean areas use soft sponge with liquid cleaner as specified on
manufacturer’s label.
• To control or prevent odor on long term incontinent applications, clean 200 OX
daily. Use of scented cleaner or disinfectant is recommended.
DISINFECTION:
• Most phenolic or quaternary type disinfectants can be used on 200 OX
fabric. User must dilute disinfectants and germicides on accordance with
manufacturer’s instructions.
• Odophor type disinfectants (Betadine, for example) will stain 200 OX fabric.
BLOOD CONTAMINATION:
• 200 OX can be disinfected with 1:10 dilution of household bleach (5.25% sodium
hypochlorite) as recommended by the CDC (US Health and Human Services)
Weaker dilution 1:100 may be used but may not be in accordance with the CDC
recommendations.
MACHINE LAUNDERING OR DRYING IS NOT RECOMMENDED
• The materials used to manufacture 200 OX and the performance of the fabric
may be adversely affected by permitting and cleaning agent to remain on contact
with the fabric for a prolonged duration or a failure to adequately rinse the agent
from the fabric.
PAGE 4

861 Taylor Rd., Suite “I”
Columbus, Ohio 43230
www.ame-medical.com
Phone: [phone]
Fax: [phone]
[email protected]
ASSEMBLY INSTRUCTIONS:
Tools Required For Assembly:
1. Hammer
2. 3/16 Inch Punch
3. 9/16 Rachet & 9/16 Box Wrench
4. 7/16 Rachet & 7/16 Box Wrench

861 Taylor Rd., Suite “I”
Columbus, Ohio 43230
www.ame-medical.com
Phone: [phone]
Fax: [phone]
[email protected]
ASSEMBLY INSTRUCTIONS:
STEP 1 The bottomm portion of the assembled bed will be in the low position. Plug bed in.
STEP 2 Insert hand control. When inserting hand control, pins of junction box must match up with plug of
hand wand.
STEP 3 Attach saddle section to the frame, inserting the four bolts from the saddle section into the four
holes on the frame. Secure saddle section by tightening bolts firmly.
STEP 4 Take head section (A)and attach saddle section(B). Match up the hinges for the pins. Insert slide
bolts and secure by tapping them firmly into place. Secure slide bolts with Clevis pins by taping
them in firmly.
STEP 5 Attach the thigh section (C) to the saddle section(D) using the same procedure in Step 4. Repeat
procedure for foot section.
STEP 6 Clevis pin in actuator tube to be attached to forks of Head and Thigh.
STEP 7 Secure foot lift bars on the sides to the frame of the bed with 1/4 inch bolts and secure with
locking nuts. Do not over thighten the bolts.
STEP 8 Raise foot to high positin and place mattress guard at foot end using a ratchet and 7/16 socket.
STEP 9 Lower foot section and take foot board (E) and place into bracket holders. Do the same for the
head board (F). The head board is wider than the foot board. Make sure the bracket holding tubes
do not face the bed when attaching the head board.