Ametek LAND LSP HD Series User manual

LSPHD System
LSPHD Linescanner Head
User Guide
Publication Nº 805233
Issue 7
Language: English
25 May 2016
© Land Instruments International, 2016

Health and Safety Information
Read all of the instructions in this booklet - including all the WARNINGS and CAUTIONS
- before using this product. If there is any instruction which you do not understand.
DO NOT USE THE PRODUCT.
Safety Signs
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in death or
personal injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, could result in minor or
moderate injury to the user or users, or result in damage to the product or to property.
CAUTION
Warning laser radiation.
Embedded laser (diode) is Class 1M, <5mW. Do not view directly with optical magniers.
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
1mW MAX OUTPUT AT 635nm
IEC 60825-1:1994
IMPORTANT: Please note radiation safety warning, where this symbol appears.
NOTE
Indicates a potentially hazardous situation which, if not avoided, could result in damage or the loss of
data.
Equipment Operation
Use of this instrument in a manner not specied by Land Instruments International may be hazardous.
Read and understand the user documentation supplied before installing and operating the equipment.
Protective Clothing, Face and Eye Protection
It is possible that this equipment is to be installed on, or near to, machinery or equipment operating at
high temperatures and high pressures. Suitable protective clothing, along with face and eye protection
must be worn. Refer to the health and safety guidelines for the machinery/equipment before installing
this product. If in doubt, contact Land Instruments International.
Electrical Power Supply
Before working on the electrical connections, all of the electrical power lines to the equipment must
be isolated. All the electrical cables and signal cables must be connected exactly as indicated in these
operating instructions. If in doubt, contact Land Instruments International.
Storage
The instrument should be stored in its packaging, in a dry sheltered area.
Unpacking
Check all packages for external signs of damage. Check the contents against the packing note.
Lifting Instructions
Where items are too heavy to be lifted manually, use suitably rated lifting equipment. Refer to the
Technical Specication for weights. All lifting should be done as stated in local regulations.
IMPORTANT INFORMATION - PLEASE READ

Health and Safety Information
Read all of the instructions in this booklet - including all the WARNINGS and CAUTIONS
- before using this product. If there is any instruction which you do not understand.
DO NOT USE THE PRODUCT.
Safety Signs
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in death or
personal injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, could result in minor or
moderate injury to the user or users, or result in damage to the product or to property.
CAUTION
Warning laser radiation.
Embedded laser (diode) is Class 1M, <5mW. Do not view directly with optical magniers.
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
1mW MAX OUTPUT AT 635nm
IEC 60825-1:1994
IMPORTANT: Please note radiation safety warning, where this symbol appears.
NOTE
Indicates a potentially hazardous situation which, if not avoided, could result in damage or the loss of
data.
Equipment Operation
Use of this instrument in a manner not specied by Land Instruments International may be hazardous.
Read and understand the user documentation supplied before installing and operating the equipment.
Protective Clothing, Face and Eye Protection
It is possible that this equipment is to be installed on, or near to, machinery or equipment operating at
high temperatures and high pressures. Suitable protective clothing, along with face and eye protection
must be worn. Refer to the health and safety guidelines for the machinery/equipment before installing
this product. If in doubt, contact Land Instruments International.
Electrical Power Supply
Before working on the electrical connections, all of the electrical power lines to the equipment must
be isolated. All the electrical cables and signal cables must be connected exactly as indicated in these
operating instructions. If in doubt, contact Land Instruments International.
Storage
The instrument should be stored in its packaging, in a dry sheltered area.
Unpacking
Check all packages for external signs of damage. Check the contents against the packing note.
Lifting Instructions
Where items are too heavy to be lifted manually, use suitably rated lifting equipment. Refer to the
Technical Specication for weights. All lifting should be done as stated in local regulations.
IMPORTANT INFORMATION - PLEASE READ
Contact Us
UK - Droneld
Land Instruments International
Tel: [phone]
Email: [email protected]
Web: www.landinst.com
USA - Pittsburgh
AMETEK Land, Inc.
Tel: [phone]
Email: [email protected]
[email protected]
Web: www.ametek-land.com
For further details on all AMETEK Land ofces, distributors and representatives, please visit
our websites.
Return of Damaged Goods
IMPORTANT If any item has been damaged in transit, this should be reported to the carrier and to the
supplier immediately. Damage caused in transit is the responsibility of the carrier not the supplier.
DO NOT RETURN a damaged instrument to the sender as the carrier will not then consider a claim. Save
the packing with the damaged article for inspection by the carrier.
Return of Goods for Repair
If you need to return goods for repair please contact our Customer Service Department. They will be
able to advise you on the correct returns procedure.
Any item returned to Land Instruments International should be adequately packaged to prevent damage
during transit.
You must include a written report of the problem together with your own name and contact information,
address, telephone number, email address etc.
Design and Manufacturing Standards
The Quality Management System of Land Instruments International is
approved to BS EN ISO 9001 for the design, manufacture and on-site
servicing of combustion, environmental monitoring and non-contact
temperature measuring instrumentation.
Approvals apply in the USA
Operation of radio transmitters, telephones or other electrical/electronic devices in close proximity
to the equipment while the enclosure doors of the instrument or its peripherals are open, may cause
interference and possible failure where the radiated emissions exceed the EMC directive.
The protection provided by this product may be invalidated if alterations or additions are made to the
structural, electrical, mechanical or pneumatic parts of this system. Such changes may also invalidate the
standard terms of warranty.
Copyright
This manual is provided as an aid to owners of Land Instruments International’s products and contains
information proprietary to Land Instruments International. This manual may not, in whole or part, be
copied, or reproduced without the expressed written consent of Land Instruments International Ltd.
Copyright © 2016 Land Instruments International.

Blank

Contents
User Guide LSPHD Linescanner Head
Contents
Preface
1 Introduction 1
1.1 Nomenclature 2
1.2 Specications-LSPHD Series 3
2 Installation 8
2.1 Introduction 8
2.2 Changing the focus distance 9
2.3 Positioning The Scanner 10
2.4 Scan Widths and Target Size 11
2.5 Alignment and Scan Direction 14
2.6 Installation Precautions 15
3 Services 16
3.1 Electrical connections: Cable requirements 16
3.2 WaterRequirements(Water-CooledUnitsOnly) 17
3.3 AirRequirements(Air-Purged/CooledUnitsOnly) 18
4 Laser Alignment 19
4.1 UsingtheLaserAlignmentUnit 20
5 Emissivity-TypicalValues 21
5.1 SettingtheEmissivityvalue 21
5.2 LSPHD 1 Series 23
5.4 LSPHD 5 Series 23
5.3 LSPHD 2 Series 23
5.5 LSPHD 6 Series 24
5.6 LSPHD7Series 24
6 SettingtheScanFrequency 25
6.1 ChangingtheScanFrequencysettingusingtheinternalswitch 25
6.2 ScanFrequencyTable 26
6.3 ScanLineSeparation 27
6.4 DataStorageRequirements 27
6.5 SkewAngle 28
7 InternalAmbientTemperatureSensor 29
7.1 Introduction 29
8 Maintenance 30
8.1 Air Purge Services 30
8.2 Water And Air Cooling Services 30
8.3 PlateMountedBlowerUnit 30
9 Installation Accessories 31
10 SoftwareVersionInformation 32
10.1 Reading the WCA program version 32
10.2 ReadingtheLSP-HDScannerversioninformation 33
10.3 ReadingtheIOversioninformation 34

Preface
User GuideLSPHD Linescanner Head
Preface
Fig. A LSPHD Head
ThisUserGuideisapplicabletothefollowingLSPHD variants:
LSPHD 10 LSPHD 5FL LSPHD 60 LSPHD71
LSPHD 11 LSPHD 50 LSPHD 61
LSPHD 20 LSPHD 52 LSPHD 62
LSPHD 21
LSPHD 22
TheUserGuidecoverstheinstallation,operationandmaintenanceoftheLSPHD
Linescanning Thermometer.
TheinstructionsgiveninthisUserGuideguideshouldbeusedinconjunctionwiththe
documentslistedbelow:
• LSPHDLinescanningThermometerInstallationGuide
• LSPHDSystemMountings&AccessoriesInstallationGuide

Page 1
User Guide LSPHD Linescanner Head
12
34
5
Fig. 1 Typical LSPHD System Overview
LSPHD SYSTEM
LSPHD Linescanner Head
Power Supply Unit
Ethernet
Ethernet
PROCESS MONITORING (optional)
Landscan
for Windows
Conguration
Software
Power over Ethernet
I/O Processor
1 Introduction
The LANDSCAN LSPHD SYSTEM uses high speed infrared detectors and precision
electronics to provide accurate linescan temperature measurement at high scan rates.
Thesystemiscompact,yetrugged,providingreliableoperationinthemostsevere
industrial environments.
The LANDSCAN LSPHD SYSTEM comprises:
• LSPHD Linescanner Head
• LSPHD Ethernet Cable
• LANDSCANforWindowsCongurationSoftware
• LANDSCANWCASoftware(Optional)
• I/OModules(Optional)
Landscan
WCA
Control Inputs & Outputs
PROCESS CONTROL
Up to four copper Ethernet
(RJ45) connections and one
optical Ethernet connection may
be made to the scanner using
the LSPHD Power Supply Unit

Page 2
User GuideLSPHD Linescanner Head
System Name:  LSP  LSPSystem
High Denition: HD Fast scan rate and High resolution
Series:   6  OperatingWavelength
Temperature Range: 1  SeeSpecications
LSP HD 6
SystemName
Series Number
Temperature Range
1.1 Nomenclature
The LSP Linescanning Thermometer detail label can be found on the black scanner
bodysection.Thelabeldisplaysthescannerserialnumber,themodelnumberandthe
'CE'conformitymark.Themodelnumberindicatesspecicinformationabouttheunit,
including 'Series Number' and 'Temperature Range'.
Example:
1
HighDenition

Page 3
User Guide LSPHD Linescanner Head
1.2 Specications-LSPHD Series
1.2.1 Common specications
Ambient temperature range 5to60°C/41to140°F(inspecication)
5to70°C/41to158°F(operating)
Alignment Class 2 Laser indicating scan plane and extent
Laser scan rate 1 Hz
Internal Ambient Temperature Sensor
(IATS)
-10to90°C/14to194°F
Emissivityrange
(remoteorinternallyset)
0.20 to 1.00
Sealing IP65
EMC
LVD
EN61326ClassA[emissions&immunity]
EN61010-1
Vibration(Anyaxis) 2g[10to30Hz]
3g[30to300Hz]
1.2.2 LSPHD 1 series specications
LSPHD 10 LSPHD 11
Operatingwavelength 1µm 1µm
Temperature range 600 to 1400 °C
1112 to 2552 °F
700to1500°C
1292to2732°F
SystemAccuracy(1)
(5to95%ofrange)
±2°C/3.6°F
Focus distance (2) 1m/39.7intoinnity(continuously
adjustable)
FieldofView
(staticto95%ofradiance)
500:1(0.002radians)
Repeatability <0.5°C/0.9°F
Temperature Resolution (3)
< 5% of range
(noise) < 15% of range
< 30% of range
Above 50% of range
≤6°C/10.8°F
≤6°C/10.8°F
≤4°C/7.2°F
≤1°C/1.8°F
Scan Angle (4) 80°
Scan Rate Factoryset
Useradjustable
50 Hz
10 to 150 Hz in 1 Hz steps
Speed of response
(Tau-linearoutputonrisingedge)
≤1µs
AmbientStability
deltaT[indicated]/deltaT[ambient]
≤1°/10°
(1)Includeserrorcorrection
(2)Focusisfactorysetto2m
(3)4lineaveragingbelow15%ofrange
(4)Scananglemaybesetintherange40to80°bythePCsoftware

Page 4
User GuideLSPHD Linescanner Head
1.2.3 LSPHD 2 series specications
LSPHD 20 LSPHD 21 LSPHD 22
Operatingwavelength 2.2 µm 1.9 µm 1.9 µm
Temperature range 200 to 850 °C
392 to 1562 °F
300 to 1000 °C
572to1832°F
400 to 1200 °C
752to2192°F
SystemAccuracy(1)
(5to95%ofrange)
±2°C/3.6°F
Focus distance (2) 1m/39.7intoinnity(continuouslyadjustable)
FieldofView
(staticto95%ofradiance)
300:1
(0.0033
radians)
500:1
(0.002radians)
500:1
(0.002radians)
Repeatability <0.5°C/0.9°F
Temperature Resolution (3)
< 5% of range
(noise) < 15% of range
< 30% of range
Above 50% of range
≤6°C/10.8°F
≤6°C/10.8°F
≤2°C/3.6°F
≤1°C/1.8°F
≤6°C/10.8°F
≤6°C/10.8°F
≤4°C/7.2°F
≤1°C/1.8°F
≤6°C/10.8°F
≤6°C/10.8°F
≤4°C/7.2°F
≤1°C/1.8°F
Scan Angle (4) 80°
Scan Rate Factoryset
Useradjustable
50 Hz
10 to 150 Hz in 1 Hz steps
Speed of response
(Tau-linearoutputonrisingedge)
≤1.5µs ≤1µs ≤1µs
AmbientStability
deltaT[indicated]/deltaT[ambient]
≤1°/10°
(1)Includeserrorcorrection
(2)Focusisfactorysetto2m
(3)4lineaveragingbelow15%ofrange
(4)Scananglemaybesetintherange40to80°bythePCsoftware

Page 5
User Guide LSPHD Linescanner Head
1.2.4 LSPHD 5 series specications
LSPHD 5FL LSPHD 50* LSPHD 52*
Operatingwavelength 5 µm 5 µm 5 µm
Temperature range 150to750°C
302 to 1382 °F
150to750°C
302 to 1382 °F
500 to 1100 °C
932 to 2012 °F
SystemAccuracy(1)
(5to95%ofrange)
±2°C/3.6°F ±2°C/3.6°F ±3°C/6.4°F
Focus distance Fixedat1200mm/47in
Targetwidth Target distance
(staticto95%radiance) <1200mm/47in
Target distance
1200 to 3000mm
47to118in
12mm/0.5in
Fieldofviewof100:1(0.01radians)
Repeatability <0.5°C/0.9°F
Temperature Resolution (2)
Below15%ofrange
(noise) Above 15% of range
≤1.5°C/2.7°F
≤1°C/1.8°F
≤1.5°C/2.7°F
≤1°C/1.8°F
≤2.5°C/4.5°F
≤2.5°C/4.5°F
Scan Angle (3) 80°
Scan Rate Factoryset 20 Hz 50 Hz 50 Hz
Useradjustable 10 to 150Hz in 1Hz steps
Speed of response
(Tau-linearoutputonrisingedge)
≤5µs
AmbientStability
deltaT[indicated]/deltaT[ambient]
≤2°/10° ≤2°/10° ≤3°/10°
Settling Time (4) 2 Hours
*LSPHD 50 and LSPHD 52 as per LSPHD 5FLunlessotherwisestated
(1)Includeserrorcorrection.Appliesonly'inapplication'
(2)Nolineaveraging.4LAreducesnoisebyfactor2
(3)Scananglemaybesetintherange40to80°bythePCsoftware
(4)Foroptimumperformance,thethermoelectriccoolertakestimetostabilisethedetectorthermally.Thisprocesstakeslongerathigherambient
temperatures.

Page 6
User GuideLSPHD Linescanner Head
1.2.5 LSPHD 6 series specications
LSPHD 60 LSPHD 61* LSPHD 62* LSPHD 63*
Operating
Wavelength
3 to 5 µm 3 to 5 µm 3 to 4.2 µm
Temperature range 20 to 250 °C
68 to 482 °F
50 to 400 °C
122to752°F
100 to 600 °C
212 to 1112 °F
SystemAccuracy (1)
(5to95%ofrange)
±2°C/3.6°F
Focus distance Fixedat1200mm/47in
Targetwidth
(staticto95%radiance)
Targetdistance<1200mm/47in 12mm/0.5in
Targetdistance1200to3000mm/
47to118in Fieldofviewof100:1(0.01radians)
Repeatability <0.5°C/0.9°F
Temperature
Resolution (2)
Below15%ofrange ≤1.5°C/2.7°F ≤1.5°C/2.7°F ≤2.5°C/4.5°F ≤2°C/3.6°F
(noise)Above15%ofrange ≤1°C/1.8°F ≤1°C/1.8°F ≤2.5°C/4.5°F
Scan Angle (3) 80 °
Scan Rate 10 to 150Hz in 1 Hz steps
Factoryset 20 Hz 50 Hz 50 Hz 50 Hz
Useradjustable
Speed of response
(Tau-linearoutputonrisingedge)
≤5µs ≤10µs
AmbientStability
deltaT[indicated]/deltaT[ambient]
<1°/10° <1°/10° <2°/10° <1°/10°
Settling Time (4) 2 Hours
*LSPHD 61, LSPHD 62, and LSPHD 63 as per LSPHD 60unlessotherwisestated
(1)Includeserrorcorrection
(2)Nolineaveraging.4LAreducesnoisebyfactor2
(3)Scananglemaybesetintherange40to80°bythePCsoftware
(4)Foroptimumperformance,thethermoelectriccoolertakestimetostabilisethedetectorthermally.Thisprocesstakeslongerathigherambient
temperatures.

Page 7
User Guide LSPHD Linescanner Head
1.2.6 LSPHD 7 series specications
LSPHD 71
Operatingwavelength 3.4 µm
Temperature range 50 to 350 °C
122 to 662 °F
SystemAccuracy(1)
(5to95%ofrange)
±2°C/3.6°F
Focus distance Fixedat1200mm/47in
Targetwidth Target distance
(staticto95%radiance) <1200mm/47in
Target distance
1200 to 3000 mm
47to118in
12mm/0.5in
Fieldofviewof100:1(0.01radians)
Repeatability <0.5°C/0.9°F
Temperature Resolution (2)
Below15%ofrange
(noise) Above 15% of range
≤4°C/7.2°F
≤2°C/3.6°F
Scan Angle (3) 80°
Scan Rate Factoryset 50 Hz
Useradjustable 10 to 150 Hz in 1 Hz steps
Speed of response
(Tau-linearoutputonrisingedge)
≤10µs
AmbientStability
deltaT[indicated]/deltaT[ambient]
≤1°/10°
Settling Time (4) 2 Hours
(1)Includeserrorcorrection
(2)Nolineaveraging.4LAreducesnoisebyfactor2
(3)Scananglemaybesetintherange40to80°bythePCsoftware
(4)Foroptimumperformance,thethermoelectriccoolertakestimetostabilisethedetectorthermally.Thisprocesstakeslongerathigherambient
temperatures.

Page 8
User GuideLSPHD Linescanner Head
2 Installation
2.1 Introduction
TheequipmentspeciedinthisUserGuidemustbeoperated,maintainedandserviced
bysuitablytrainedpersonnel,capableofcarefullyfollowingtheprocedures,warnings
andguidelinesgiven.ItisadvisablethatallUserGuidesandInstallationGuides
associatedwithLSPHDSystemequipmentshouldbereadthoroughlyandbekeptreadily
available.
CAUTION
Ensure that the LSPHDHeadismountedsecurely,inalocationwheretheeffects
of vibration, dust and fumes are kept to a minimum. Ensure that the scanning
sight path is not obscured.
The LSPHD10,20&21haveafocusdistancefactorysetat2000mm/79in.
RefertoSection2.2fordetailsofhowtochangethefocusdistance.
Chooseamountinglocationwhichminimisesexternalheatingofthescanner.
Iftheambienttemperatureoftheunitexceedsthespeciedmaximum,a
coolingsystem(availablefromAMETEKLand)mustbetted.
Iftheinstrumentistobeusedinenvironmentswheregasesresultingfrom
combustionarepresent,contactAMETEKLandsothattheapplicationcanbe
fullyassessedbeforeyouinstallthescanner.
Fig.2FocusadjustmentfortheLSPHD 1, LSPHD 11, LSPHD 20, LSPHD 21 and LSPHD 22
Focusing ring
Clamping plate

Page 9
User Guide LSPHD Linescanner Head
2.2 Changing the focus distance
 (LSPHD 10,LSPHD 11,LSPHD 20,LSPHD 21&LSPHD 22 only)
The focus distance of the LSPHD 10, LSPHD 11, LSPHD 20, LSPHD 21 and LSPHD 22,
linescannerheadisfactorysetto2m/79in.Thefocusdistancecanbeuser-adjusted
intherange1m/40intoinnity.
1) Removethefrontcoverofthescanner(thepanelnearestthelaserswitch).
RefertoFig.2.ThefocuscanbeadjustedbyturningtheFocusing ring,which
isheldinplacebytheClamping plate.
2) RemovethetopscrewfromtheClamping plate to free the Focusing ring.
3) Inordertofocustheinstrumentaccurately,thefocusingmechanismmustrstbe
'zeroed'. Rotate the Focusing ringinthedirectionofthe'Focuslong'arrow(i.e.
totheright)untilitiswoundinfully.
4) Refertothetablebelow.RotatetheFocusing ring to the left for the number of
turnsrequiredtomatchthefocusdistanceyouwanttoset.
Thetablebelowgivesthefocusdistancesthatcanbeachievedbyturningthe
focusingring.Eachscrewholeonthefocusingringisat0.05ofaturn.
Focus distance
m / in
LSPHD 10
LSPHD 11
LSPHD 20 LSPHD 21
LSPHD 22
Numberofturnsfromfullywoundin
1.0/40 7.70 8.95 8.45
1.2/4.7 6.80 8.00 7.50
1.5/59 5.85 7.05 6.60
2.0/79 4.95 6.15 5.65
3.0/118 4.05 5.20 4.70
4.0/157 3.60 4.70 4.25
5.0/197 3.35 4.45 4.00
6.0/236 3.15 4.25 3.80
7.0/276 3.00 4.15 3.70
8.0/315 2.95 4.05 3.60
10.0/394 2.80 3.90 3.45
Innity 2.30 3.40 2.95
5) Toadjustthefocustoadistanceotherthanthatquotedintheabovetable,rotate
the focusing ring to the required intermediate position.
6) Whenyouhavefocusedthescannertotherequireddistance,therewillbeahole
in the Focusing ring thatalignswiththeholeintheClamping plate(youmay
needtoadjusttheFocusingringslightly).Insertandtightenthescrewthrough
the Clamping plate to secure the Focusing ring in position.
7) Replacethecoverpanel.
 Thescannerisnowfocused.

Page 10
User GuideLSPHD Linescanner Head
Fig.3Scanwidthandtargetsizedimensions
40°
80°
TargetPath(TP)
Target
Distance
(TD)
ScanWidth(SW)
x axis
yaxis
x axis
yaxis
TP = TD
cos 40
Targetspotbecomesmoreellipticalwith
increased distance from scan centre line.
Seetargetsizetablesforxandyaxis
sizes at ±40°
2.3 Positioning The Scanner
Before installing the scanner, refer to the cautions given in Section 2.1.
The scanner must be installed so that the target plane is parallel to the scanner
window.
RefertoFig.3(below).Thewidthofthescan(SW)isproportionaltothedistance
(TD)betweenthescannerandthetargetplane.Chooseatargetdistancethatwillgive
ascanlinethatjustexceedsthewidthoftheproduct,asthisgivesmaximumspatial
resolution.

Page 11
User Guide LSPHD Linescanner Head
2.4 Scan Widths and Target Size
2.4.1 Scan Width
ThefullscananglefortheLSPScanneris80°,andtheScanWidth(SW)canbe
calculated as:
 SW=(TD+35)x1.678mm
or
 SW=(TD+1.38)x1.678inches
 Where‘TD’istheperpendicularTargetDistancebetweentheLSPwindowandthe
target plane.
Atthescanangleextremes(±40°)thelengthoftheTargetPath(TP)betweenthe
scanner and the target is:
 TP=(TD+35)/0.766mm
or
 TP=(TD+1.38)/0.766inches
Note
Theactivescananglemaybesetintherange40to80°.SeetheLandscan
CongurationorWCAsoftwareguidesforfurtherinformation.
2.4.2 Target Size
ThecalculatedTargetSizeisstrictlyonlycircularatascanangleofzerodegrees,i.e.
perpendicular to the instrument.
Atallotherscanangles,thetargetspotwillbeanellipse.Theellipticaltargetsizeis
showninthefollowingtablesforthescanangleextremes(±40°).

Page 12
User GuideLSPHD Linescanner Head
2.4.3 LSPHD 1 & 2 Target size table The nominal Target Size (TS)isgivenby: TS = TD / FoV Where‘FoV’istheinstrument’sFieldofView • LSPHD 10, LSPHD 11, LSPHD21&LSPHD 22 FoV=500:1 • LSPHD20     FoV=300:1
TD SW TP LSPHD 10, LSPHD 11, LSPHD 21 & LSPHD 22
Target Size
LSPHD 20-TargetSize
Target Distance Scan Width Target Path 0° Scan angle ±40°(xaxis) ±40°(yaxis) 0° Scan angle ±40°(xaxis) ±40°(yaxis)
mm in mm in mm in mm in mm in mm in mm in mm in mm in
1000 39.4 1737 68.4 1305 51.4 2.0 0.08 7.8 0.31 6.0 0.24 3.3 0.13 10.0 0.39 7.7 0.30 1250 49.2 2156 84.9 1632 64.3 2.5 0.10 8.7 0.34 6.7 0.26 4.2 0.17 11.5 0.45 8.8 0.35 1500 59.1 2576 101.4 1958 77.1 3.0 0.12 9.6 0.38 7.4 0.29 5.0 0.20 13.0 0.51 10.0 0.39 1750 68.9 2996 118.0 2284 89.9 3.5 0.14 10.5 0.41 8.0 0.31 5.8 0.23 14.4 0.57 11.0 0.43 2000 78.7 3415 134.4 2611 102.8 4.0 0.16 11.4 0.45 8.7 0.34 6.7 0.26 16.0 0.63 12.2 0.48 2500 98.4 4254 167.5 3264 128.5 5.0 0.20 13.1 0.52 10.0 0.39 8.3 0.33 18.7 0.74 14.4 0.57 3000 118.1 5093 200.5 3916 154.2 6.0 0.24 14.8 0.58 11.4 0.45 10.0 0.39 21.6 0.85 16.5 0.65 3600 141.7 6100 240.2 4700 185.0 7.2 0.28 17.0 0.67 13.0 0.51 12.0 0.47 25.0 0.98 19.2 0.76 4000 157.5 6772 266.6 5222 205.6 8.0 0.31 18.3 0.72 14.0 0.55 6000 236.2 10128 398.7 7832 308.3 12.0 0.47 25.1 0.99 19.2 0.76 8000 315.0 13484 530.9 10443 410.7
Notes: 1) Theindicatedtargetsizesassumethatthefocusdistanceoftheinstrumentequalsthetargetdistance. 2) Iftheinstrumentisfocusedatadistancebetweenthe‘targetdistance’andthe‘targetpath’,thetargetsizeatthescan
angleextremeswillreduceattheexpenseofanincreaseatzerodegreesscanangle.

Page 13
User Guide LSPHD Linescanner Head
2.4.4 LSPHD 5, 6 & 7 Target size table
The nominal Target Size (TS)isgivenby:
• At target distances less than1200mm/47in:
TS = 12mm / 0.47in
or
• At target distances greater than1200mm/47in:
TS = TD / FoV
• LSPHD 5, LSPHD6&LSPHD7 FoV=100:1
TD SW TP LSPHD 5, LSPHD 6 & LSPHD 7
Target Size
Target Distance Scan Width Target Path 0° Scan angle ±40°(xaxis) ±40°(yaxis)
mm in mm in mm in mm in mm in mm in
200 7.9 394 15.5 261 10.3 12.0 0.47 15.7 0.62 12.0 0.47
500 19.7 898 35.4 653 25.7 12.0 0.47 15.7 0.62 12.0 0.47
750 29.5 1317 51.9 979 38.5 12.0 0.47 15.7 0.62 12.0 0.47
1000 39.4 1737 68.4 1305 51.4 12.0 0.47 17.0 0.67 13.1 0.52
1200 47.2 2073 81.6 1566 61.7 12.0 0.47 20.4 0.80 15.7 0.62
1500 59.1 2576 101.4 1958 77.1 15.0 0.59 25.5 1.00 19.5 0.77
2000 78.7 3415 134.5 2611 102.8 20.0 0.79 34.0 1.34 26.0 1.02
3000 118.1 5093 200.5 3916 154.2 30.0 1.18 51.0 2.00 39.0 1.54
4000 157.5 6772 266.6 5222 205.6 40.0 1.57 68.0 2.68 52.0 2.05

Page 14
User GuideLSPHD Linescanner Head
Scan Direction Arrowhead
Scan Direction
Product Pass Direction
Product
LSP Scanner
2.5 Alignment and Scan Direction
EachAMETEKLandLSP HD Head has an integral laser unit that can be used to help align
thescannerduringinstallation.Forinstructionsonhowtousethelaseralignmentunit,
refertoSection4.0ofthisUserGuide.
Tointerpretthescanproleproducedbythescanner,thescandirectionoftheunitmust
beknown.Thescandirectionisindicatedbyanembossedarrowheadcastintothetop
ofthescannercasing(SeeFig.4overleaf).
Thedesignofthescannermountingsensuresthatthescannerwillalwaysbereplacedin
the correct orientation, should the scanner be removed from the application for servicing
etc.
Fig. 4 Scan Direction