Ametek ThePoint Series User manual

Leader in
Level Measurement
Installation and
Operating Instructions
ThePointTM Series
Two Wire Point Level Switch
Auto-Calibration or Manual Calibration
Selectable
Telephone: [phone]
Fax: [phone]
E-mail: [email protected]
Website: www.drexelbrook.com

AMETEK Drexelbrook makes no warranty of any kind with regard to the material contained

purpose. Drexelbrook shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the performance or use of material.
© Copyright AMETEK Drexelbrook

EDO # 05-19-110
PMT1-LM

ThePointTM Series
Two Wire Point Level Switch
Auto-Calibration or Manual Calibration
Selectable

Contents

Contents
Section 1:Introduction ........................................................................................................ 1
1.1 System Description .............................................................................................. 1
1.2 Technology ........................................................................................................... 1
1.3 Model Number...................................................................................................... 2
1.4 Housing Dimensions ........................................................................................... 4
Section 2:Installation .......................................................................................................... 5
2.1 Unpacking ............................................................................................................ 5
2.2 Mounting and Installation Guidelines ................................................................... 5
2.3 Input Wiring .......................................................................................................... 8
2.4 Output and LED Status ........................................................................................ 8
2.5 Electronic Unit ..................................................................................................... 9
2.6 Spark Protection..................................................................................................11
2.7 Sensing Element Connection..............................................................................11
2.8 Calibration .......................................................................................................... 13
Section 3:Troubleshooting ............................................................................................... 21
3.1 Testing Sensing Element.................................................................................... 21
3.2 Testing Electronic Unit........................................................................................ 22
3.3 Over Range........................................................................................................ 23
3.4 Under Range...................................................................................................... 23
3.5 Testing Integral Cable ........................................................................................ 23
3.6 Testing Remote Cable........................................................................................ 24
3.7 Factory Assistance ............................................................................................. 24
3.8 Field Service ...................................................................................................... 25
3.9 Customer Training.............................................................................................. 25
3.10 Equipment Return .............................................................................................. 25
3.11 RF Point Level Troubleshooting Guide .............................................................. 26
Section 4: Specications................................................................................................... 27
Section 5:Approvals Available ......................................................................................... 29
Section 6:Control Drawings ............................................................................................. 31
6.1 FM / FMc Control Drawings ............................................................................... 31
6.2 ATEX Control Drawings...................................................................................... 44
6.3 Heavy Duty Spark Protection ............................................................................. 50
6.4 Adding a Padded Capacitor ............................................................................... 52
6.5 Dual Seal Assembly for 700 Series Sensing Elements...................................... 55
Appendix A Shortening or Lengthening Sensing Element............................................A1

Section 1

The Point™ Series Introduction
1
Section 1: Introduction
1.1 System Description
The AMETEK Drexelbrook ThePoint™ Series uses No-Cal™
technology to detect the presence or absence of material
without calibration or initiation via setpoint adjustments,
push-buttons, or magnets.
Installation is simple and easy. Simply apply power and
ThePoint system is ready to detect the presence or absence
of material. Since ThePoint instrument does not require
calibration or setpoint adjustments, it is capable of operating
in non-dedicated tanks regardless of the material being
measured.
1.2 Technology
In a simple capacitance probe type sensing element,
when the level rises and material covers the probe, the
capacitance within the circuit between the probe and the
media (conductive applications) or the probe and the vessel
wall (insulating applications) increases. This is due to the
dielectric constant (k) of the material which causes a bridge
misbalance. The signal is demodulated (rectied), amplied,
and the output is increased. There are drawbacks, however,
especially when there is coating of the probe.
An RF Admittance level transmitter is the next generation.
Although similar to the capacitance concept, ThePoint
employs a radio frequency signal and adds the Cote-Shield™
circuitry within the Electronics Unit.
This patented Cote-Shield™ circuitry is designed into
ThePoint series and enables the instrument to ignore the
effect of buildup or material coating on the sensing element.
The sensing element is mounted in the vessel and provides
a change in RF admittance indicating presence or absence
of material. The Cote-Shield element of the sensing element
prevents the transmission of RF current through the coating
on the sensing element. The only path to ground available
for the RF current is through the material being measured.
The result is an accurate measurement regardless of the
amount of coating on the probe, making it by far the most
versatile technology, good for very wide range conditions
from cryogenics to high temperature, from vacuum to 10,000
psi pressure, and works with all types of materials.
Figure 1-2
RF Admittance
Probe with Cote-Shield
k
air
A
d
Ckmedia
C=kA
d
C = k A
d
A
k
air
d
C
kmedia
The sensing
element must be
uncovered before
applying power.
Figure 1-1
Simple Capacitance
Probe

The Point™ Series Introduction
2
Sensing Element
Application Sensing Element Pressure/Temperature Wetted Parts
00 General purpose 700-1202-001 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and PEEK
700-1202-021 integral
01 Floating roof with 700-1202-012 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS, Brass,
cable attachment 700-1202-022 integral and PEEK
and brass bottom weight
02 General purpose, 700-1202-014 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and PEEK
longer insertion lengths 700-1202-024 integral
with cable attachment
and 316SS bottom weight
03 Proximity 700-1202-018 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and PEEK
700-1202-028 integral with 76 mm (3)
316SS proximity plate
04 General purpose, 700-1202-041 remote 69 bar @ 121°C (1000 PSI @ 250°F) 316SS and PEEK
high temperature 700-1202-042 integral 20.7 bar @ 232°C (300 PSI @ 450°F)
and pressure
06 General purpose with 700-1202-031 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and FDA grade
FDA approved 700-1202-032 integral PEEK
materials of construction
07 General purpose 700-1202-010 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and PEEK with
Granular materials 700-1202-020 integral 7/8 inch dia. 316SS collar
09 General purpose 700-1202-033 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and FDA grade
Granular materials with 700-1202-034 integral PEEK with 7/8 inch dia.
FDA approved 316SS collar
10 Corrosive liquids (2)(4)(9) 700-0001-018 remote 3.4 bar @ 149°C (50 PSI @ 300°F) PFA
11 General purpose, 700-0201-005 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) 316SS and TFE
TFE compatibility required 34.5 bar @ 149°C (500psi @ 300°F)
12 Corrosive material, 700-0201-005 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) Hastelloy C and TFE
higher pressure Hastelloy C 34.5 bar @ 149°C (500psi @ 300°F)
13 Sanitary (3) Non 3A 700-0201-019 int/rem 13.8 bar @ 149°C (200 PSI @ 300°F) 316/316L SS and TFE
14 General Purpose, LP 700-0202-002 int/rem 3.4 bar @ 149°C (50 PSI @ 300°F) 316SS and TFE
15 Heavy duty, agitated 700-0202-043 remote 69 bar @ 38°C (1000 PSI @ 100°F) 316SS and TFE
tanks or material 34.5 bar @ 149°C (500psi @ 300°F)
with high bulk density (1)
16 High Integrity Seal for 700-0002-360 int/rem 34.5 bar @ 149°C (500 PSI @ 300°F) PFA
Hazardous Materials
17 Sanitary (3) Non 3A LP 700-0202-029 int/rem 3.4 bar @ 149°C (50 PSI @ 300°F) 316SS and TFE
18 Corrosive material, 700-0001-022 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) TFE
higher pressure with 34.5 bar @ 149°C (500 PSI @ 300°F)
waterlike viscosity (4)
19 Interface Measurement 700-0002-023 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) 316SS and TFE
34.5 bar @ 149°C (500 PSI @ 300°F)
20 Miniature Pilot 700-0209-002 remote 6.9 bar @ 121°C (100 PSI @ 250°F) 316 SS and TFE
Plant Sensor (1)(7) 0 bar @ 232°C (0 PSI @ 450°F)
Fly Ash Precipitators, Baghouse, and Economizers (1) (6)
31 No hopper Installation 700-0029-001 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
32 Hopper Installation 700-0029-002 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 200mm (8 inches)
33 Hopper Installation 700-0029-003 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 406mm (16 inches)
34 Hopper Instalation 700-0029-004 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 521mm (20.5 inches)
35 Hopper Installation 700-0029-005 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 635mm (25 inches)
Plugged Chute Detection (1) (5)
50 Flush Mount Sensor 700-0207-001 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 304 SS and
305mm2(12 inches2) Polyurethane
heavy duty
51 Flush Mount Sensor 700-0207-002 remote 0.1 bar @ 149°C (1 PSI @ 300°F) 304 SS and TFE
305mm2(12 inches2)
higher temperature
52 Flush Mount Sensor 700-0207-003 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 304 SS and Neoprene
305mm2(12 inches2)
with curved radius 153, 229, 305 mm (6, 9, or 12 inches)
53 Flush Mount Sensor 700-0207-004 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 410 SS and UHMW
305mm2(12 inches2) Polyethylene
extra heavy duty
55 Flush Mount Sensor 700-0207-006 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 304 SS and
203mm2 (8 inches2) Polyurethane
heavy duty
67 3A Sanitary Sensor 700-3201-001 remote 13.8 bar @ 121°C (200 psi @ 250°F) 316 SS and PEEK
700-3201-002 integral
High Pressure / High Temperature
60 High Pressure & Temp. 700-0204-038 remote 137.9 bar @ 93°C (2000 PSI @ 200°F) 316SS and Ceramic
68.9 bar @ 260°C (1000 PSI @ 500°F)
61 High Temperature (1) 700-0204-002 remote 0 bar @ 816°C (0 PSI @ 1500°F) 316SS and Ceramic
62 High Pressure & Temp. 700-0204-048 remote 275.8 bar @316°C (4000 PSI @ 600°F) 316SS
ZZ Sensing Element Not Listed
Output
1One DPDT Relay, dry contacts, 5A, 120VAC (Min 100 mA / 12 VDC)
2One DPDT Relay, gold plated contacts (Max 200 mA / 12 VDC)
Housing
Technology
PRF Admittance
Input
LUniversal Power Supply 19-250 VAC, 18-200 VDC
Measurement Type
N Std Auto Cal
LStd 2 pF Fixed
T10 pF Auto Cal
V10 pF Fixed
HHi Sense .5 pF Auto Cal
PHi Sense .5 pF Fixed
GHi Sense Manual
MStd Sense Manual
Electronics
0Integral
1Remote, no cable
2Rmt. w/ 3 m (10 ft.) G.P. cable
3Rmt. w/ 7.6 m (25 ft.) G.P. cable
4Rmt. w/ 10.6 m (35 ft.) G.P. cable
5Rmt. w/ 15.2 m (50 ft.) G.P. cable
6Rmt. w/ 23 m (75 ft.) G.P. cable
IL CSL
xxxG 457 mm (18") 0 mm (0")
xxxH 914 mm (36") 254 mm (10")
xxxJ 914 mm (36") 0 mm (0")
xxxK 1219 mm (48") 254 mm (10")
xxxL 1524 mm (60") 254 mm (10")
P00X IL/CSL Other
A1BX IL/CSL factory set for Fly Ash
xxxZ Other
IL CSL
xxx1 457 mm (18") 152 mm (6")
xxx2 305 mm (12") 152 mm (6")
xxxA 152 mm (6") 51 mm (2")
xxxB 305 mm (12") 51 mm (2")
xxxC 305 mm (12") 89 mm (3.5")
xxxD 457 mm (18") 51 mm (2")
xxxE 457 mm (18") 89 mm (3.5")
xxxF 457 mm (18") 254 mm (10")
Mounting Type (See separate Mounting Chart for first three digits)
(1) Available with remote electronics only
(2) Use A1P mounting option
(3) Choose only sanitary mounting options
(4) Available with 0-inch CSL only
(5) Use P00X mounting option
(6) Use A1B mounting option
(7) Use A8B mounting option (¼-inch NPT)
(8) Choose from flange mounting only
(9) FM approved with remote electronics only
Not all mounting options available with all
sensing elements
7Rmt. w/ (25 ft.) Tri-Ax Cable
8Rmt. w/ (50 ft.) Tri-Ax Cable
9Rmt. w/ (75 ft.) Tri-Ax Cable
ARmt. w/ (10 ft.) Hi-Temp. Cable
BRmt. w/ (25 ft.) 1st 10ft Hi-Temp. Cbl.
CRmt. w/ (35 ft.) 1st 10ft Hi-Temp. Cbl.
DRmt. w/ (50 ft.) 1st 10ft Hi-Temp. Cbl.
ERmt. w/ (75 ft.) 1st 10ft Hi-Temp. Cbl.
FRmt. w/ (5 ft.) G.P. Cable
GRmt. w/ (5 ft.) Tri-Ax Cable
HRmt. w/ (10 ft.) Tri-Ax Cable
JRmt. w/ (35 ft.) Tri-Ax Cable
KRmt. w/ (5 ft.) Hi-Temp. Cable
Notes: CSL (Cote-Shield Length) should extend through Nozzle + Typical "Wall Buildup" + 2 Inches
Sensing Element
Application Sensing Element Pressure/Temperature Wetted Parts
00 General purpose 700-1202-001 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and PEEK
700-1202-021 integral
01 Floating roof with 700-1202-012 remote 13.8 bar @ 177°C (200 PSI @ 350°F) 316SS, Brass,
cable attachment 700-1202-022 integral and PEEK
and brass bottom weight
02 General purpose, 700-1202-014 remote 13.8 bar @ 177°C (200 PSI @ 350°F) 316SS and PEEK
longer insertion lengths 700-1202-024 integral
with cable attachment
and 316SS bottom weight
03 Proximity 700-1202-018 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and PEEK
700-1202-028 integral with 76 mm (3)
316SS proximity plate
04 General purpose, 700-1202-041 remote 69 bar @ 121°C (1000 PSI @ 250°F) 316SS and PEEK
high temperature 700-1202-042 integral 20.7 bar @ 232°C (300 PSI @ 450°F)
and pressure
06 General purpose with 700-1202-031 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and FDA grade
FDA approved 700-1202-032 integral PEEK
materials of construction
07 General purpose 700-1202-010 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and PEEK with
Granular materials 700-1202-020 integral 7/8 inch dia. 316SS collar
09 General purpose 700-1202-033 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and FDA grade
Granular materials with 700-1202-034 integral PEEK with 7/8 inch dia.
FDA approved 316SS collar
materials of construction
10 Corrosive liquids (2)(4)(9) 700-0001-018 remote 3.4 bar @ 149°C (50 PSI @ 300°F) PFA
11 General purpose, 700-0201-005 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) 316SS and TFE
higher pressure 13.8 bar @ 232°C (200 PSI @ 450°F)
TFE compatibility required
12 Corrosive material, 700-0201-005 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) Hastelloy C and TFE
higher pressure Hastelloy C 13.8 bar @ 232°C (200 PSI @ 450°F)
13 Sanitary (3) Non 3A 700-0201-019 int/rem 13.8 bar @ 149°C (200 PSI @ 300°F) 316/316L SS and TFE
14 General Purpose, 700-0202-002 int/rem 3.4 bar @ 149°C (50 PSI @ 300°F) 316SS and TFE
low pressure 1.4 bar @ 232°C (20 PSI @ 450°F)
15 Heavy duty, agitated 700-0202-043 remote 69 bar @ 38°C (1000 PSI @ 100°F) 316SS and TFE
tanks or material 13.8 bar @ 232°C (200 PSI @ 450°F)
with high bulk density (1)
16 High Integrity Seal for 700-0002-360 int/rem 34.5 bar @ 149°C (500 PSI @ 300°F) PFA
Hazardous Materials
17 Sanitary (3) Non 3A LP 700-0202-029 int/rem 3.4 bar @ 149°C (50 PSI @ 300°F) 316SS and TFE
18 Corrosive material, 700-0001-022 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) TFE
higher pressure with 34.5 bar @ 149°C (500 PSI @ 300°F)
waterlike viscosity (4)
19 Interface Measurement 700-0002-023 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) 316SS and TFE
34.5 bar @ 149°C (500 PSI @ 300°F)
20 Miniature Pilot 700-0209-002 remote 6.9 bar @ 121°C (100 PSI @ 250°F) 316 SS and TFE
Plant Sensor (1)(7) 0 bar @ 232°C (0 PSI @ 450°F)
Fly Ash Precipitators, Baghouse, and Economizers (1) (6)
31 No hopper Installation 700-0029-001 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
32 Hopper Installation 700-0029-002 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 200mm (8 inches)
33 Hopper Installation 700-0029-003 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 406mm (16 inches)
34 Hopper Instalation 700-0029-004 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 521mm (20.5 inches)
35 Hopper Installation 700-0029-005 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 635mm (25 inches)
Plugged Chute Detection (1) (5)
50 Flush Mount Sensor 700-0207-001 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 304 SS and
305mm2(12 inches2) Polyurethane
heavy duty
51 Flush Mount Sensor 700-0207-002 remote 0.1 bar @ 149°C (1 PSI @ 300°F) 304 SS and TFE
305mm2(12 inches2)
higher temperature
52 Flush Mount Sensor 700-0207-003 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 304 SS and Neoprene
305mm2(12 inches2)
with curved radius 153, 229, 305 mm (6, 9, or 12 inches)
53 Flush Mount Sensor 700-0207-004 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 410 SS and UHMW
305mm2(12 inches2) Polyethylene
extra heavy duty
55 Flush Mount Sensor 700-0207-006 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 304 SS and
203mm2 (8 inches2) Polyurethane
heavy duty
67 3A Sanitary Sensor 700-3201-001 remote 13.8 bar @ 121°C (200 psi @ 250°F) 316 SS and PEEK
700-3201-002 integral
High Pressure / High Temperature
60 High Pressure & Temp. 700-0204-038 remote 137.9 bar @ 93°C (2000 PSI @ 200°F) 316SS and Ceramic
68.9 bar @ 260°C (1000 PSI @ 500°F)
61 High Temperature (1) 700-0204-002 remote 0 bar @ 816°C (0 PSI @ 1500°F) 316SS and Ceramic
62 High Pressure & Temp. 700-0204-048 remote 275.8 bar @316°C (4000 PSI @ 600°F) 316SS
ZZ Sensing Element Not Listed
Output
08-16 mA
Housing
Technology
PRF Admittance
Input
TTwo Wire Power Supply 13 to 30 Vdc
Electronics
0Integral
1Remote, no cable
2Rmt. w/ 3 m (10 ft.) G.P. cable
3Rmt. w/ 7.6 m (25 ft.) G.P. cable
4Rmt. w/ 10.6 m (35 ft.) G.P. cable
5Rmt. w/ 15.2 m (50 ft.) G.P. cable
6Rmt. w/ 23 m (75 ft.) G.P. cable
IL CSL
xxxG 457 mm (18") 0 mm (0")
xxxH 914 mm (36") 254 mm (10")
xxxJ 914 mm (36") 0 mm (0")
xxxK 1219 mm (48") 254 mm (10")
xxxL 1524 mm (60") 254 mm (10")
P00X IL/CSL Other
A1BX IL/CSL factory set for Fly Ash
xxxZ Other
IL CSL
xxx1 457 mm (18") 152 mm (6")
xxx2 305 mm (12") 152 mm (6")
xxxA 152 mm (6") 51 mm (2")
xxxB 305 mm (12") 51 mm (2")
xxxC 305 mm (12") 89 mm (3.5")
xxxD 457 mm (18") 51 mm (2")
xxxE 457 mm (18") 89 mm (3.5")
xxxF 457 mm (18") 254 mm (10")
Mounting Type (See separate Mounting Chart for first three digits)
7Rmt. w/ (25 ft.) Tri-Ax Cable
8Rmt. w/ (50 ft.) Tri-Ax Cable
9Rmt. w/ (75 ft.) Tri-Ax Cable
ARmt. w/ (10 ft.) Hi-Temp. Cable
BRmt. w/ (25 ft.) 1st 10ft Hi-Temp. Cbl.
CRmt. w/ (35 ft.) 1st 10ft Hi-Temp. Cbl.
DRmt. w/ (50 ft.) 1st 10ft Hi-Temp. Cbl.
ERmt. w/ (75 ft.) 1st 10ft Hi-Temp. Cbl.
FRmt. w/ (5 ft.) G.P. Cable
GRmt. w/ (5 ft.) Tri-Ax Cable
HRmt. w/ (10 ft.) Tri-Ax Cable
JRmt. w/ (35 ft.) Tri-Ax Cable
KRmt. w/ (5 ft.) Hi-Temp. Cable
TP 0
NPT Threads
A1B ¾"NPT 316SS
A1C ¾"NPT Hastelloy C
A1P ¾"NPT PFA
A2B 1"NPT 316SS
A2C 1"NPT Hastelloy C
Sanitary TriClamps
C2B 1"TriClamp 316SS
C3B 1½"TriClamp 316SS
C4B 2"TriClamp 316SS
C5B 2-1/2" TriClamp 316SS
C6B 3” TriClamp 316SS
C7B 4" TriClamp 316SS
ANSI Flanges
DA1 1" 150# RF 316/316L SS
DB1 1½" 150# RF 316/316L SS
DC1 2" 150# RF 316/316L SS
DD1 2½" 150# RF 316/316L SS
DE1 1" 300# RF 316/316L SS
DF1 1½" 300# RF 316/316L SS
DG1 2" 300# RF 316/316L SS
DH1 2½" 300# RF 316/316L SS
DI1 3" 150# RF 316/316L SS
DJ1 3" 300# RF 316/316L SS
DK1 4" 150# RF 316/316L SS
DL1 4" 300# RF 316/316L SS
DM1 6" 150# RF 316/316L SS
DN1 6" 300# RF 316/316L SS
DA2 1" 150# RF CS
DB2 1½" 150# RF CS
DC2 2" 150# RF CS
DD2 2½" 150# RF CS
DE2 1" 300# RF CS
DF2 1½" 300# RF CS
DG2 2" 300# RF CS
DH2 2½" 300# RF CS
DI2 3" 150# RF CS
DJ2 3" 300# RF CS
DK2 4" 150# RF CS
DL2 4" 300# RF CS
DM2 6" 150# RF CS
DN2 6" 300# RF CS
DIN Flanges
E01 25 mm 16 bar RF 316/316L SS
EP1 25 mm 40 bar RF 316/316L SS
EQ1 50 mm 16 bar RF 316/316L SS
ER1 50 mm 40 bar RF 316/316L SS
ES1 80 mm 16 bar RF 316/316L SS
ET1 80 mm 40 bar RF 316/316L SS
EU1 100 mm 16 bar RF 316/316L SS
EV1 100 mm 40 bar RF 316/316L SS
EW1 150 mm 16 bar RF 316/316L SS
EX1 150 mm 40 bar RF 316/316L SS
E02 25 mm 16 bar RF CS
EP2 25 mm 40 bar RF CS
EQ2 50 mm 16 bar RF CS
ER2 50 mm 40 bar RF CS
ES2 80 mm 16 bar RF CS
ET2 80 mm 40 bar RF CS
EU2 100 mm 16 bar RF CS
EV2 100 mm 40 bar RF CS
EW2 150 mm 16 bar RF CS
EX2 150 mm 40 bar RF CS
NPT Threads
A1B ¾"NPT 316SS
A1C ¾"NPT Hastelloy C
A1P ¾"NPT PFA
A2B 1"NPT 316SS
A2C 1"NPT Hastelloy C
Sanitary TriClamps
C2B 1"TriClamp 316SS
C3B 1½"TriClamp 316SS
C4B 2"TriClamp 316SS
C5B 2-1/2" TriClamp 316SS
C6B 3” TriClamp 316SS
C7B 4" TriClamp 316SS
ANSI Flanges
DA1 1" 150# RF 316/316L SS
DB1 1½" 150# RF 316/316L SS
DC1 2" 150# RF 316/316L SS
DD1 2½" 150# RF 316/316L SS
DE1 1" 300# RF 316/316L SS
DF1 1½" 300# RF 316/316L SS
DG1 2" 300# RF 316/316L SS
DH1 2½" 300# RF 316/316L SS
DI1 3" 150# RF 316/316L SS
DJ1 3" 300# RF 316/316L SS
DK1 4" 150# RF 316/316L SS
DL1 4" 300# RF 316/316L SS
DM1 6" 150# RF 316/316L SS
DN1 6" 300# RF 316/316L SS
DA2 1" 150# RF CS
DB2 1½" 150# RF CS
DC2 2" 150# RF CS
DD2 2½" 150# RF CS
DE2 1" 300# RF CS
DF2 1½" 300# RF CS
DG2 2" 300# RF CS
DH2 2½" 300# RF CS
DI2 3" 150# RF CS
DJ2 3" 300# RF CS
DK2 4" 150# RF CS
DL2 4" 300# RF CS
DM2 6" 150# RF CS
DN2 6" 300# RF CS
DIN Flanges
E01 25 mm 16 bar RF 316/316L SS
EP1 25 mm 40 bar RF 316/316L SS
EQ1 50 mm 16 bar RF 316/316L SS
ER1 50 mm 40 bar RF 316/316L SS
ES1 80 mm 16 bar RF 316/316L SS
ET1 80 mm 40 bar RF 316/316L SS
EU1 100 mm 16 bar RF 316/316L SS
EV1 100 mm 40 bar RF 316/316L SS
EW1 150 mm 16 bar RF 316/316L SS
EX1 150 mm 40 bar RF 316/316L SS
E02 25 mm 16 bar RF CS
EP2 25 mm 40 bar RF CS
EQ2 50 mm 16 bar RF CS
ER2 50 mm 40 bar RF CS
ES2 80 mm 16 bar RF CS
ET2 80 mm 40 bar RF CS
EU2 100 mm 16 bar RF CS
EV2 100 mm 40 bar RF CS
EW2 150 mm 16 bar RF CS
EX2 150 mm 40 bar RF CS
(1) Available with remote electronics only
(2) Use A1P mounting option
(3) Choose only sanitary mounting options
(4) Available with 0-inch CSL only
(5) Use P00X mounting option
(6) Use A1B mounting option
(7) Use A8B mounting option (¼-inch NPT)
(8) Choose from flange mounting only
(9) FM approved with remote electronics only
Not all mounting options available with all
sensing elements
Notes: CSL (Cote-Shield Length) should extend through Nozzle + Typical "Wall Buildup" + 2 Inches
0 No Approvals(Remote), NEMA 4X/IP66, M20 X 1.5 conduit entries
1 No Approvals, NEMA 4X/IP66, ¾” conduit entries
2 ATEX / IECEx, NEMA 4X/IP66, M20 X 1.5 conduit entries
3 FM / FMc approved, NEMA 4X/IP66, ¾” conduit entries
5 No Approvals, NEMA 4X/IP66, M20 conduit entries, Dual Seal, Perm-a-Seal Sensors – only
6 FM / FMc approved (Integral), No Approvals (Remote), NEMA 4X/IP66, ¾” conduit entries, Dual Seal, Perm-a-Seal Sensors – only
7 FM / FMc approved (Remote), NEMA 4X/IP66, ¾” conduit entries, Dual Seal, Perm-a-Seal Sensors – only
8 No Approvals (Integral), NEMA 4X/IP66, ¾” conduit entries, Dual Seal, Perm-a-Seal Sensors – only
9 FM / FMc approved (Integral), No Approvals (Remote), NEMA 4X/IP66, M20 conduit entries, Dual Seal, Perm-a-Seal Sensors – only
A No Approvals (Remote), NEMA 4X/IP66, ¾” conduit entries, Dual Seal,Perm-a-Seal Sensors – only
B FM / FMc approved (Remote), NEMA 4X/IP66, ¾” conduit entries, Dual Seal, Perm-a-Seal Sensors – only
0No Approvals, NEMA 4X/IP66, M20 X 1.5 conduit entries
1No Approvals, NEMA 4X/IP66, ¾” NPT conduit entries
2ATEX / IECEx, NEMA 4X/IP66, M20 X 1.5 conduit entries
3FM / FMc, NEMA 4X/IP66, ¾” NPT conduit entries
5No Approvals, NEMA 4X/IP66, M20 conduit entries, Dual Seal, Perm-a-Seal sensors – only
6No approvals, NEMA 4X/IP66, ¾” NPT conduit entries, Dual Seal, Perm-a-Seal sensors – only
7FM / FMc Approved, NEMA 4X/IP66, ¾” NPT conduit entries, Dual Seal, Perm-a-Seal sensors – only
9No approvals, NEMA 4X/IP66, M20 conduit entries, Dual Seal, Non Perm-a-Seal sensors – only
ANo Approvals, NEMA 4X/IP66, ¾” NPT conduit entries, Dual Seal, Non Perm-a-Seal sensors – only
BFM / FMc Approved, NEMA 4X/IP66, ¾” NPT conduit entries, Dual Seal, Non Perm-a-Seal sensors – only
Measurement Type
N Std Auto Cal
LStd 2 pF Fixed
T10 pF Auto Cal
V10 pF Fixed
HHi Sense .5 pF Auto Cal
PHi Sense .5 pF Fixed
GHi Sense Manual
MStd Sense Manual
1.3 Model Number
Continued on Next Page
All Calibration modes are built
into the standard unit. Modes
can be changed in the eld as
required (See Section 2.8.9)

The Point™ Series Introduction
3
1.3 Model Number (continued)
(Continued from previous page)
Sensing Element
Application Sensing Element Pressure/Temperature Wetted Parts
00 General purpose 700-1202-001 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and PEEK
700-1202-021 integral
01 Floating roof with 700-1202-012 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS, Brass,
cable attachment 700-1202-022 integral and PEEK
and brass bottom weight
02 General purpose, 700-1202-014 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and PEEK
longer insertion lengths 700-1202-024 integral
with cable attachment
and 316SS bottom weight
03 Proximity 700-1202-018 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and PEEK
700-1202-028 integral with 76 mm (3)
316SS proximity plate
04 General purpose, 700-1202-041 remote 69 bar @ 121°C (1000 PSI @ 250°F) 316SS and PEEK
high temperature 700-1202-042 integral 20.7 bar @ 232°C (300 PSI @ 450°F)
and pressure
06 General purpose with 700-1202-031 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and FDA grade
FDA approved 700-1202-032 integral PEEK
materials of construction
07 General purpose 700-1202-010 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and PEEK with
Granular materials 700-1202-020 integral 7/8 inch dia. 316SS collar
09 General purpose 700-1202-033 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and FDA grade
Granular materials with 700-1202-034 integral PEEK with 7/8 inch dia.
FDA approved 316SS collar
10 Corrosive liquids (2)(4)(9) 700-0001-018 remote 3.4 bar @ 149°C (50 PSI @ 300°F) PFA
11 General purpose, 700-0201-005 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) 316SS and TFE
TFE compatibility required 34.5 bar @ 149°C (500psi @ 300°F)
12 Corrosive material, 700-0201-005 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) Hastelloy C and TFE
higher pressure Hastelloy C 34.5 bar @ 149°C (500psi @ 300°F)
13 Sanitary (3) Non 3A 700-0201-019 int/rem 13.8 bar @ 149°C (200 PSI @ 300°F) 316/316L SS and TFE
14 General Purpose, LP 700-0202-002 int/rem 3.4 bar @ 149°C (50 PSI @ 300°F) 316SS and TFE
15 Heavy duty, agitated 700-0202-043 remote 69 bar @ 38°C (1000 PSI @ 100°F) 316SS and TFE
tanks or material 34.5 bar @ 149°C (500psi @ 300°F)
with high bulk density (1)
16 High Integrity Seal for 700-0002-360 int/rem 34.5 bar @ 149°C (500 PSI @ 300°F) PFA
Hazardous Materials
17 Sanitary (3) Non 3A LP 700-0202-029 int/rem 3.4 bar @ 149°C (50 PSI @ 300°F) 316SS and TFE
18 Corrosive material, 700-0001-022 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) TFE
higher pressure with 34.5 bar @ 149°C (500 PSI @ 300°F)
waterlike viscosity (4)
19 Interface Measurement 700-0002-023 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) 316SS and TFE
34.5 bar @ 149°C (500 PSI @ 300°F)
20 Miniature Pilot 700-0209-002 remote 6.9 bar @ 121°C (100 PSI @ 250°F) 316 SS and TFE
Plant Sensor (1)(7) 0 bar @ 232°C (0 PSI @ 450°F)
Fly Ash Precipitators, Baghouse, and Economizers (1) (6)
31 No hopper Installation 700-0029-001 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
32 Hopper Installation 700-0029-002 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 200mm (8 inches)
33 Hopper Installation 700-0029-003 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 406mm (16 inches)
34 Hopper Instalation 700-0029-004 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 521mm (20.5 inches)
35 Hopper Installation 700-0029-005 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 635mm (25 inches)
Plugged Chute Detection (1) (5)
50 Flush Mount Sensor 700-0207-001 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 304 SS and
305mm2(12 inches2) Polyurethane
heavy duty
51 Flush Mount Sensor 700-0207-002 remote 0.1 bar @ 149°C (1 PSI @ 300°F) 304 SS and TFE
305mm2(12 inches2)
higher temperature
52 Flush Mount Sensor 700-0207-003 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 304 SS and Neoprene
305mm2(12 inches2)
with curved radius 153, 229, 305 mm (6, 9, or 12 inches)
53 Flush Mount Sensor 700-0207-004 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 410 SS and UHMW
305mm2(12 inches2) Polyethylene
extra heavy duty
55 Flush Mount Sensor 700-0207-006 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 304 SS and
203mm2 (8 inches2) Polyurethane
heavy duty
67 3A Sanitary Sensor 700-3201-001 remote 13.8 bar @ 121°C (200 psi @ 250°F) 316 SS and PEEK
700-3201-002 integral
High Pressure / High Temperature
60 High Pressure & Temp. 700-0204-038 remote 137.9 bar @ 93°C (2000 PSI @ 200°F) 316SS and Ceramic
68.9 bar @ 260°C (1000 PSI @ 500°F)
61 High Temperature (1) 700-0204-002 remote 0 bar @ 816°C (0 PSI @ 1500°F) 316SS and Ceramic
62 High Pressure & Temp. 700-0204-048 remote 275.8 bar @316°C (4000 PSI @ 600°F) 316SS
ZZ Sensing Element Not Listed
Output
1One DPDT Relay, dry contacts, 5A, 120VAC (Min 100 mA / 12 VDC)
2One DPDT Relay, gold plated contacts (Max 200 mA / 12 VDC)
Housing
Technology
PRF Admittance
Input
LUniversal Power Supply 19-250 VAC, 18-200 VDC
Measurement Type
N Std Auto Cal
LStd 2 pF Fixed
T10 pF Auto Cal
V10 pF Fixed
HHi Sense .5 pF Auto Cal
PHi Sense .5 pF Fixed
GHi Sense Manual
MStd Sense Manual
Electronics
0Integral
1Remote, no cable
2Rmt. w/ 3 m (10 ft.) G.P. cable
3Rmt. w/ 7.6 m (25 ft.) G.P. cable
4Rmt. w/ 10.6 m (35 ft.) G.P. cable
5Rmt. w/ 15.2 m (50 ft.) G.P. cable
6Rmt. w/ 23 m (75 ft.) G.P. cable
IL CSL
xxxG 457 mm (18") 0 mm (0")
xxxH 914 mm (36") 254 mm (10")
xxxJ 914 mm (36") 0 mm (0")
xxxK 1219 mm (48") 254 mm (10")
xxxL 1524 mm (60") 254 mm (10")
P00X IL/CSL Other
A1BX IL/CSL factory set for Fly Ash
xxxZ Other
IL CSL
xxx1 457 mm (18") 152 mm (6")
xxx2 305 mm (12") 152 mm (6")
xxxA 152 mm (6") 51 mm (2")
xxxB 305 mm (12") 51 mm (2")
xxxC 305 mm (12") 89 mm (3.5")
xxxD 457 mm (18") 51 mm (2")
xxxE 457 mm (18") 89 mm (3.5")
xxxF 457 mm (18") 254 mm (10")
Mounting Type (See separate Mounting Chart for first three digits)
(1) Available with remote electronics only
(2) Use A1P mounting option
(3) Choose only sanitary mounting options
(4) Available with 0-inch CSL only
(5) Use P00X mounting option
(6) Use A1B mounting option
(7) Use A8B mounting option (¼-inch NPT)
(8) Choose from flange mounting only
(9) FM approved with remote electronics only
Not all mounting options available with all
sensing elements
7Rmt. w/ (25 ft.) Tri-Ax Cable
8Rmt. w/ (50 ft.) Tri-Ax Cable
9Rmt. w/ (75 ft.) Tri-Ax Cable
ARmt. w/ (10 ft.) Hi-Temp. Cable
BRmt. w/ (25 ft.) 1st 10ft Hi-Temp. Cbl.
CRmt. w/ (35 ft.) 1st 10ft Hi-Temp. Cbl.
DRmt. w/ (50 ft.) 1st 10ft Hi-Temp. Cbl.
ERmt. w/ (75 ft.) 1st 10ft Hi-Temp. Cbl.
FRmt. w/ (5 ft.) G.P. Cable
GRmt. w/ (5 ft.) Tri-Ax Cable
HRmt. w/ (10 ft.) Tri-Ax Cable
JRmt. w/ (35 ft.) Tri-Ax Cable
KRmt. w/ (5 ft.) Hi-Temp. Cable
Notes: CSL (Cote-Shield Length) should extend through Nozzle + Typical "Wall Buildup" + 2 Inches
Sensing Element
Application Sensing Element Pressure/Temperature Wetted Parts
00 General purpose 700-1202-001 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and PEEK
700-1202-021 integral
01 Floating roof with 700-1202-012 remote 13.8 bar @ 177°C (200 PSI @ 350°F) 316SS, Brass,
cable attachment 700-1202-022 integral and PEEK
and brass bottom weight
02 General purpose, 700-1202-014 remote 13.8 bar @ 177°C (200 PSI @ 350°F) 316SS and PEEK
longer insertion lengths 700-1202-024 integral
with cable attachment
and 316SS bottom weight
03 Proximity 700-1202-018 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and PEEK
700-1202-028 integral with 76 mm (3)
316SS proximity plate
04 General purpose, 700-1202-041 remote 69 bar @ 121°C (1000 PSI @ 250°F) 316SS and PEEK
high temperature 700-1202-042 integral 20.7 bar @ 232°C (300 PSI @ 450°F)
and pressure
06 General purpose with 700-1202-031 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and FDA grade
FDA approved 700-1202-032 integral PEEK
materials of construction
07 General purpose 700-1202-010 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and PEEK with
Granular materials 700-1202-020 integral 7/8 inch dia. 316SS collar
09 General purpose 700-1202-033 remote 13.8 bar @ 232°C (200 PSI @ 450°F) 316SS and FDA grade
Granular materials with 700-1202-034 integral PEEK with 7/8 inch dia.
FDA approved 316SS collar
materials of construction
10 Corrosive liquids (2)(4)(9) 700-0001-018 remote 3.4 bar @ 149°C (50 PSI @ 300°F) PFA
11 General purpose, 700-0201-005 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) 316SS and TFE
higher pressure 13.8 bar @ 232°C (200 PSI @ 450°F)
TFE compatibility required
12 Corrosive material, 700-0201-005 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) Hastelloy C and TFE
higher pressure Hastelloy C 13.8 bar @ 232°C (200 PSI @ 450°F)
13 Sanitary (3) Non 3A 700-0201-019 int/rem 13.8 bar @ 149°C (200 PSI @ 300°F) 316/316L SS and TFE
14 General Purpose, 700-0202-002 int/rem 3.4 bar @ 149°C (50 PSI @ 300°F) 316SS and TFE
low pressure 1.4 bar @ 232°C (20 PSI @ 450°F)
15 Heavy duty, agitated 700-0202-043 remote 69 bar @ 38°C (1000 PSI @ 100°F) 316SS and TFE
tanks or material 13.8 bar @ 232°C (200 PSI @ 450°F)
with high bulk density (1)
16 High Integrity Seal for 700-0002-360 int/rem 34.5 bar @ 149°C (500 PSI @ 300°F) PFA
Hazardous Materials
17 Sanitary (3) Non 3A LP 700-0202-029 int/rem 3.4 bar @ 149°C (50 PSI @ 300°F) 316SS and TFE
18 Corrosive material, 700-0001-022 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) TFE
higher pressure with 34.5 bar @ 149°C (500 PSI @ 300°F)
waterlike viscosity (4)
19 Interface Measurement 700-0002-023 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) 316SS and TFE
34.5 bar @ 149°C (500 PSI @ 300°F)
20 Miniature Pilot 700-0209-002 remote 6.9 bar @ 121°C (100 PSI @ 250°F) 316 SS and TFE
Plant Sensor (1)(7) 0 bar @ 232°C (0 PSI @ 450°F)
Fly Ash Precipitators, Baghouse, and Economizers (1) (6)
31 No hopper Installation 700-0029-001 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
32 Hopper Installation 700-0029-002 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 200mm (8 inches)
33 Hopper Installation 700-0029-003 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 406mm (16 inches)
34 Hopper Instalation 700-0029-004 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 521mm (20.5 inches)
35 Hopper Installation 700-0029-005 remote 0.1 bar @ 260°C (2 PSI @ 500°F) 316SS and TFE
up to 635mm (25 inches)
Plugged Chute Detection (1) (5)
50 Flush Mount Sensor 700-0207-001 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 304 SS and
305mm2(12 inches2) Polyurethane
heavy duty
51 Flush Mount Sensor 700-0207-002 remote 0.1 bar @ 149°C (1 PSI @ 300°F) 304 SS and TFE
305mm2(12 inches2)
higher temperature
52 Flush Mount Sensor 700-0207-003 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 304 SS and Neoprene
305mm2(12 inches2)
with curved radius 153, 229, 305 mm (6, 9, or 12 inches)
53 Flush Mount Sensor 700-0207-004 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 410 SS and UHMW
305mm2(12 inches2) Polyethylene
extra heavy duty
55 Flush Mount Sensor 700-0207-006 remote 0.1 bar @ 82°C (1 PSI @ 180°F) 304 SS and
203mm2 (8 inches2) Polyurethane
heavy duty
67 3A Sanitary Sensor 700-3201-001 remote 13.8 bar @ 121°C (200 psi @ 250°F) 316 SS and PEEK
700-3201-002 integral
High Pressure / High Temperature
60 High Pressure & Temp. 700-0204-038 remote 137.9 bar @ 93°C (2000 PSI @ 200°F) 316SS and Ceramic
68.9 bar @ 260°C (1000 PSI @ 500°F)
61 High Temperature (1) 700-0204-002 remote 0 bar @ 816°C (0 PSI @ 1500°F) 316SS and Ceramic
62 High Pressure & Temp. 700-0204-048 remote 275.8 bar @316°C (4000 PSI @ 600°F) 316SS
ZZ Sensing Element Not Listed
Output
08-16 mA
Housing
Technology
PRF Admittance
Input
TTwo Wire Power Supply 13 to 30 Vdc
Electronics
0Integral
1Remote, no cable
2Rmt. w/ 3 m (10 ft.) G.P. cable
3Rmt. w/ 7.6 m (25 ft.) G.P. cable
4Rmt. w/ 10.6 m (35 ft.) G.P. cable
5Rmt. w/ 15.2 m (50 ft.) G.P. cable
6Rmt. w/ 23 m (75 ft.) G.P. cable
IL CSL
xxxG 457 mm (18") 0 mm (0")
xxxH 914 mm (36") 254 mm (10")
xxxJ 914 mm (36") 0 mm (0")
xxxK 1219 mm (48") 254 mm (10")
xxxL 1524 mm (60") 254 mm (10")
P00X IL/CSL Other
A1BX IL/CSL factory set for Fly Ash
xxxZ Other
IL CSL
xxx1 457 mm (18") 152 mm (6")
xxx2 305 mm (12") 152 mm (6")
xxxA 152 mm (6") 51 mm (2")
xxxB 305 mm (12") 51 mm (2")
xxxC 305 mm (12") 89 mm (3.5")
xxxD 457 mm (18") 51 mm (2")
xxxE 457 mm (18") 89 mm (3.5")
xxxF 457 mm (18") 254 mm (10")
Mounting Type (See separate Mounting Chart for first three digits)
7Rmt. w/ (25 ft.) Tri-Ax Cable
8Rmt. w/ (50 ft.) Tri-Ax Cable
9Rmt. w/ (75 ft.) Tri-Ax Cable
ARmt. w/ (10 ft.) Hi-Temp. Cable
BRmt. w/ (25 ft.) 1st 10ft Hi-Temp. Cbl.
CRmt. w/ (35 ft.) 1st 10ft Hi-Temp. Cbl.
DRmt. w/ (50 ft.) 1st 10ft Hi-Temp. Cbl.
ERmt. w/ (75 ft.) 1st 10ft Hi-Temp. Cbl.
FRmt. w/ (5 ft.) G.P. Cable
GRmt. w/ (5 ft.) Tri-Ax Cable
HRmt. w/ (10 ft.) Tri-Ax Cable
JRmt. w/ (35 ft.) Tri-Ax Cable
KRmt. w/ (5 ft.) Hi-Temp. Cable
TP 0
NPT Threads
A1B ¾"NPT 316SS
A1C ¾"NPT Hastelloy C
A1P ¾"NPT PFA
A2B 1"NPT 316SS
A2C 1"NPT Hastelloy C
Sanitary TriClamps
C2B 1"TriClamp 316SS
C3B 1½"TriClamp 316SS
C4B 2"TriClamp 316SS
C5B 2-1/2" TriClamp 316SS
C6B 3” TriClamp 316SS
C7B 4" TriClamp 316SS
ANSI Flanges
DA1 1" 150# RF 316/316L SS
DB1 1½" 150# RF 316/316L SS
DC1 2" 150# RF 316/316L SS
DD1 2½" 150# RF 316/316L SS
DE1 1" 300# RF 316/316L SS
DF1 1½" 300# RF 316/316L SS
DG1 2" 300# RF 316/316L SS
DH1 2½" 300# RF 316/316L SS
DI1 3" 150# RF 316/316L SS
DJ1 3" 300# RF 316/316L SS
DK1 4" 150# RF 316/316L SS
DL1 4" 300# RF 316/316L SS
DM1 6" 150# RF 316/316L SS
DN1 6" 300# RF 316/316L SS
DA2 1" 150# RF CS
DB2 1½" 150# RF CS
DC2 2" 150# RF CS
DD2 2½" 150# RF CS
DE2 1" 300# RF CS
DF2 1½" 300# RF CS
DG2 2" 300# RF CS
DH2 2½" 300# RF CS
DI2 3" 150# RF CS
DJ2 3" 300# RF CS
DK2 4" 150# RF CS
DL2 4" 300# RF CS
DM2 6" 150# RF CS
DN2 6" 300# RF CS
DIN Flanges
E01 25 mm 16 bar RF 316/316L SS
EP1 25 mm 40 bar RF 316/316L SS
EQ1 50 mm 16 bar RF 316/316L SS
ER1 50 mm 40 bar RF 316/316L SS
ES1 80 mm 16 bar RF 316/316L SS
ET1 80 mm 40 bar RF 316/316L SS
EU1 100 mm 16 bar RF 316/316L SS
EV1 100 mm 40 bar RF 316/316L SS
EW1 150 mm 16 bar RF 316/316L SS
EX1 150 mm 40 bar RF 316/316L SS
E02 25 mm 16 bar RF CS
EP2 25 mm 40 bar RF CS
EQ2 50 mm 16 bar RF CS
ER2 50 mm 40 bar RF CS
ES2 80 mm 16 bar RF CS
ET2 80 mm 40 bar RF CS
EU2 100 mm 16 bar RF CS
EV2 100 mm 40 bar RF CS
EW2 150 mm 16 bar RF CS
EX2 150 mm 40 bar RF CS
NPT Threads
A1B ¾"NPT 316SS
A1C ¾"NPT Hastelloy C
A1P ¾"NPT PFA
A2B 1"NPT 316SS
A2C 1"NPT Hastelloy C
Sanitary TriClamps
C2B 1"TriClamp 316SS
C3B 1½"TriClamp 316SS
C4B 2"TriClamp 316SS
C5B 2-1/2" TriClamp 316SS
C6B 3” TriClamp 316SS
C7B 4" TriClamp 316SS
ANSI Flanges
DA1 1" 150# RF 316/316L SS
DB1 1½" 150# RF 316/316L SS
DC1 2" 150# RF 316/316L SS
DD1 2½" 150# RF 316/316L SS
DE1 1" 300# RF 316/316L SS
DF1 1½" 300# RF 316/316L SS
DG1 2" 300# RF 316/316L SS
DH1 2½" 300# RF 316/316L SS
DI1 3" 150# RF 316/316L SS
DJ1 3" 300# RF 316/316L SS
DK1 4" 150# RF 316/316L SS
DL1 4" 300# RF 316/316L SS
DM1 6" 150# RF 316/316L SS
DN1 6" 300# RF 316/316L SS
DA2 1" 150# RF CS
DB2 1½" 150# RF CS
DC2 2" 150# RF CS
DD2 2½" 150# RF CS
DE2 1" 300# RF CS
DF2 1½" 300# RF CS
DG2 2" 300# RF CS
DH2 2½" 300# RF CS
DI2 3" 150# RF CS
DJ2 3" 300# RF CS
DK2 4" 150# RF CS
DL2 4" 300# RF CS
DM2 6" 150# RF CS
DN2 6" 300# RF CS
DIN Flanges
E01 25 mm 16 bar RF 316/316L SS
EP1 25 mm 40 bar RF 316/316L SS
EQ1 50 mm 16 bar RF 316/316L SS
ER1 50 mm 40 bar RF 316/316L SS
ES1 80 mm 16 bar RF 316/316L SS
ET1 80 mm 40 bar RF 316/316L SS
EU1 100 mm 16 bar RF 316/316L SS
EV1 100 mm 40 bar RF 316/316L SS
EW1 150 mm 16 bar RF 316/316L SS
EX1 150 mm 40 bar RF 316/316L SS
E02 25 mm 16 bar RF CS
EP2 25 mm 40 bar RF CS
EQ2 50 mm 16 bar RF CS
ER2 50 mm 40 bar RF CS
ES2 80 mm 16 bar RF CS
ET2 80 mm 40 bar RF CS
EU2 100 mm 16 bar RF CS
EV2 100 mm 40 bar RF CS
EW2 150 mm 16 bar RF CS
EX2 150 mm 40 bar RF CS
(1) Available with remote electronics only
(2) Use A1P mounting option
(3) Choose only sanitary mounting options
(4) Available with 0-inch CSL only
(5) Use P00X mounting option
(6) Use A1B mounting option
(7) Use A8B mounting option (¼-inch NPT)
(8) Choose from flange mounting only
(9) FM approved with remote electronics only
Not all mounting options available with all
sensing elements
Notes: CSL (Cote-Shield Length) should extend through Nozzle + Typical "Wall Buildup" + 2 Inches
0 No Approvals(Remote), NEMA 4X/IP66, M20 X 1.5 conduit entries
1 No Approvals, NEMA 4X/IP66, ¾” conduit entries
2 ATEX / IECEx, NEMA 4X/IP66, M20 X 1.5 conduit entries
3 FM / FMc approved, NEMA 4X/IP66, ¾” conduit entries
5 No Approvals, NEMA 4X/IP66, M20 conduit entries, Dual Seal, Perm-a-Seal Sensors – only
6 FM / FMc approved (Integral), No Approvals (Remote), NEMA 4X/IP66, ¾” conduit entries, Dual Seal, Perm-a-Seal Sensors – only
7 FM / FMc approved (Remote), NEMA 4X/IP66, ¾” conduit entries, Dual Seal, Perm-a-Seal Sensors – only
8 No Approvals (Integral), NEMA 4X/IP66, ¾” conduit entries, Dual Seal, Perm-a-Seal Sensors – only
9 FM / FMc approved (Integral), No Approvals (Remote), NEMA 4X/IP66, M20 conduit entries, Dual Seal, Perm-a-Seal Sensors – only
A No Approvals (Remote), NEMA 4X/IP66, ¾” conduit entries, Dual Seal,Perm-a-Seal Sensors – only
B FM / FMc approved (Remote), NEMA 4X/IP66, ¾” conduit entries, Dual Seal, Perm-a-Seal Sensors – only
0No Approvals, NEMA 4X/IP66, M20 X 1.5 conduit entries
1No Approvals, NEMA 4X/IP66, ¾” NPT conduit entries
2ATEX / IECEx, NEMA 4X/IP66, M20 X 1.5 conduit entries
3FM / FMc, NEMA 4X/IP66, ¾” NPT conduit entries
5No Approvals, NEMA 4X/IP66, M20 conduit entries, Dual Seal, Perm-a-Seal sensors – only
6No approvals, NEMA 4X/IP66, ¾” NPT conduit entries, Dual Seal, Perm-a-Seal sensors – only
7FM / FMc Approved, NEMA 4X/IP66, ¾” NPT conduit entries, Dual Seal, Perm-a-Seal sensors – only
9No approvals, NEMA 4X/IP66, M20 conduit entries, Dual Seal, Non Perm-a-Seal sensors – only
ANo Approvals, NEMA 4X/IP66, ¾” NPT conduit entries, Dual Seal, Non Perm-a-Seal sensors – only
BFM / FMc Approved, NEMA 4X/IP66, ¾” NPT conduit entries, Dual Seal, Non Perm-a-Seal sensors – only
Measurement Type
N Std Auto Cal
LStd 2 pF Fixed
T10 pF Auto Cal
V10 pF Fixed
HHi Sense .5 pF Auto Cal
PHi Sense .5 pF Fixed
GHi Sense Manual
MStd Sense Manual

The Point™ Series Introduction
4
Figure 1-3
Compartment Housing Detail
Equipotential Terminal
(CENELEC Systems)
4.5"
(114mm)
6.5"
(165mm)
4.75"
(121mm)
1.4 Housing Dimensions

ThePoint™ Series Installation
5
Section 2: Installation
2.1 Unpacking
Carefully remove the contents of the shipping carton and
check each item against the packing list before destroying
any packing material. If there is any shortage or damage,
immediately report it to the factory at + 215-674-1234.
2.2 Mounting and Installation Guidelines
WARNING:
ThePoint equipment is rated explosion-proof. When
installing in explosion hazardous areas [rated
“potential hazardous” (EU) or “hazardous classied”
(USA)] observe all national and local regulations as well as
specications in the certicate.
CAUTION:
ThePoint instrument must be powered after it is installed
in the application and with material below the sensing
element.
ThePoint instrument can be mounted vertically, horizontally,
or at an angle. Mounting location should be as free as
possible from vibration, corrosive atmospheres, and any
possibility of mechanical damage. Ambient temperatures at
electronics should be between -30 to 70ºC (-22 to 158ºF).
NOTE:
To reduce possibility of damage caused by water in conduit,
install drip loop and breather drain in conduit to purge any
accumulating moisture as shown in Figure 2-1.
Cable ttings
supplied are weather-
resistant.
They are NOT
certied as
explosionproof (XP) or
ameproof (d) unless
they are specically
marked.
Figure 2-1
Recommended
Conduit Connection

ThePoint™ Series Installation
6
After system is installed and level is below sensing element,
apply power. ThePoint series instrument does not require
any calibration or setpoint adjustments and is ready to detect
change in level.
If properly installed, the green LED will light when power is
applied. Neither the green nor red LED should be ashing.
If either of the LEDs are ashing, refer to, Section 3,
Troubleshooting,
Mount sensing element per guidelines in Figure 2-2.
NOZZLE
NOZZLE
Wall build-up
does not extend
past first
insulator.
Cote-shield must
extend through
nozzle and wall
build-up by 2".
Wrong
Nozzle too long;
Cote-shield too short.
Factory-supplied Cote-shield
extends through nozzle and
wall build-up.
Best
Best
No Nozzle
Good
Long Nozzle
2.2 Mounting and Installation Guidelines (continued)
The Point RF
instrument is rated
Intrinsically Safe
(I.S.) when power is
provided from and
I.S. supply.
Figure 2-2
Installation
Considerations
• When installing ThePoint instrument, ambient
temperature at electronics must not exceed 70°C
(158°F).
• When installing ange-mounted sensing elements,
keep mating surfaces and bolts free of paint and
corrosion to ensure proper electrical contact with
vessel. Avoid using excessive amounts of TeonTM tape
when installing threaded sensing elements.
• Install systems with threaded NPT connection via
wrench ats on the process connection ONLY.
• Locate sensing element to avoid enhancing
electrostatic discharge from process medium, as is
good practice with any thermowell, displacer, or
sampler. This includes correct bonding to tank or silo
wall.

ThePoint™ Series Installation
7
• If installation area is rated explosion-proof and
requires conduit seal ttings, they should be used in
accordance with company standards and local codes.
• Mounting sensing element inside a pipe is not
recommended.
• Do not mount a Cote-Shield sensing element through a
nozzle that exceeds length of rst insulator.
• Ensure that there are no obstructions or agitator
blades to interfere with sensing element.
• Rigid sensing elements can be mounted at any angle.
2.2.1 Installation of Flush-Mounted Sensing Elements
These instructions apply to all ush on/off sensing elements,
models 700-0207-001, 700-0207-002, 700-0207-003, 700-0207-
004, 700-0207-006. These systems will sense presence of
material (no ow or plugged chute) and absence of material
(ow or empty chute) at the sensing element. The Flush
Sensing Element will ignore free falling material.
Material Backed-Up Above
Sensing Element
(No Flow)
Sensing Element at the Top of a Chute.
• The ush sensing element should be mounted
In The Flow Stream.These sensing elements
are designed and built to withstand the impact
of coal, rock, wood, chips, etc. This location
is important to prevent excessive build up of
material on the face of the sensing element.
• Excessive build up, typically consisting of wet
and/or sticky nes, can occur if the sensing
element is protected from falling material.
Sensing Element in an angle chute.
• Do not mount on the top or bottom.
• Best mounted on either side
Sensing Element at the Bottom
• Mount on any side.
• Low-Level sensors can be used to
detect a plug or to insure that a
seal is present (chute is full at this
point).
2.2 Mounting and Installation Guidelines (continued)

ThePoint™ Series Installation
8
32
L2L1
1
G
GND
Loop
13-30Vdc
2.3 Input Wiring
WARNING:
If ThePoint instrument is located in a hazardous
environment, do not open enclosure cover or make/break any
electrical connections without rst disconnecting electrical
power at the source. Ensure that wiring, electrical ttings,
and conduit connections conform to electrical codes for the
specic location and hazard level.
Figure 2-3
Input Wiring
Figure 2-4
Output/LED Status
LED
On
LED
Off
RED
Power
GREEN
High Level FailSafe
Tank Empty
High Level FailSafe
Tank Full
Low Level FailSafe
Tank Full
Low Level FailSafe
Tank Empty
Tank Condition
LED
On
LED
On
RED
Power
GREEN
LED
On
LED
On
RED
Power
GREEN
LED
On
LED
Off
RED
Power
GREEN
LED Output Status
2.4 Output and LED Status
There are two status LEDs located on top of the Electronic
Unit. The green LED is used to indicate that the unit has
power. The red LED is used to indicate the output condition.
See Figure 2-4.
LED
On
LED
Off
RED
Power
GREEN
High Level FailSafe
Tank Empty
High Level FailSafe
Tank Full
Low Level FailSafe
Tank Full
Low Level FailSafe
Tank Empty
Tank Condition
LED
On
LED
On
RED
Power
GREEN
LED
On
LED
On
RED
Power
GREEN
LED
On
LED
Off
RED
Power
GREEN
LED Output Status
LED
On
LED
Off
RED
Power
GREEN
High Level FailSafe
Tank Empty
High Level FailSafe
Tank Full
Low Level FailSafe
Tank Full
Low Level FailSafe
Tank Empty
Tank Condition
LED
On
LED
On
RED
Power
GREEN
LED
On
LED
On
RED
Power
GREEN
LED
On
LED
Off
RED
Power
GREEN
LED Output Status

ThePoint™ Series Installation
9
Figure 2-5
Electronic Unit
Adjustments
2.5 Electronic Unit
Remove housing lid to access status LEDs, time delay
adjustment, and conguration jumpers. See Figure 2-5.
2.5.1 Time Delay
Time delay adjustment is used to avoid an oscillating output
due to agitation or waves in the vessel. The time delay
adjustment can be eld adjusted from 0 to 60 seconds. Unit is
shipped with time delay setting at zero seconds.
The Time Delay adjustment is a 270-Degree turn pot and is
at zero seconds when in the full counter-clockwise position.
Do not force the pot past the stop or damage will occur.
2.5.2 Time Delay Action
Time delay action describes whether the output is delayed
from going into the alarm state or recovering from an alarm
state.
• FWD: Delays system from coming out of alarm.
• REV: Delays system from going into alarm.
• The instrument is supplied with time delay action set
in forward mode (FWD) position.
• Time delay action is eld-selectable using a jumper
located on top of Electronic Unit. See Figure 2-5.
2.5.3 Current Output Assignment
The output current can be congured using the jumpers as
follows:
• Jumper on pin #1 and #2 creates:
8mA - Normal
16mA - Alarm
• Jumper on pin #2 and #3 creates:
8mA - Alarm
16mA - Normal
VIEW
TIME DELAY JUMPER
Right = Forward Acting
Left=Reverse Acting
TIME DELAY
ADJUSTMENT
0-60 SEC.
PIN #1
FAILSAFE JUMPER
Right = High Level
Left=Low Level
OUTPUT
Right = 8mA Alarm
16 mA Normal
Left = 8mA Normal
16 mA Alarm
GREEN LED - POWER
RED LED - ALARM
MANUAL CALIBRATION
ADJUSTMENT POT
RESET/RECAL
BUTTON
NOTE:
DO NOT PUSH the ReCal button without first
ensuring that the material being measured is
below the sensing element.

ThePoint™ Series Installation
10
2.5.4 Failsafe
Failsafe describes the level condition that causes the
transmitter to go into alarm.
• High Level FailSafe (HLFS) is the condition when the
probe is covered, the unit goes into alarm.
• Low Level FailSafe (LLFS) is the condition when the
probe is uncovered, the unit goes into alarm.
• Instrument is supplied with failsafe jumper set in high
level (HLFS) position.
• Failsafe is eld-selectable using a jumper located on top
of the Electronic Unit. See Figure 2-5.
2.5.5 RECAL
CAUTION:
ThePoint instrument must be powered after it is installed in
the application and with material below the sensing element.
If system is powered on the bench prior to installation, or
moved from one tank to another, RECAL is necessary to
allow software to capture the air capacitance generated by
sensing element in tank.
Merely press and hold the RECAL button (See Figure 2-5).
for at least ve seconds. Both LED's ash for 60 seconds
before reset occurs. [Remove power from the system while the
LED's are ashing and recalibration will occur immediately].
NOTE:
Do Not Push the Recal Button without rst ensuring
that the material being measured is below the sensing
element.

ThePoint™ Series Installation
11
2.6 Spark Protection
Applications involving insulating granulars and insulating
liquids may produce a static discharge that can damage the
electronics. The RF series instrument is supplied with
integral heavy-duty spark protection to prevent static
discharges from damaging the electronic circuits.
2.7 Sensing Element Connection (Integral Sensing Elements)
Sensing element connects to the rear side of the circuit board
and is factory-installed.
The sensing element is sealed to the housing and cannot be
removed without permanent damage.
Figure 2-6
Sensing Element
Connection
(Integral Housing)
MODEL
NUMBER
LABEL

ThePoint™ Series Installation
12
Figure 2-7
Sensing Element Connection
(Remote Housing)
For ThePoint instruments mounted remotely from sensing
element, cable connections from sensing element to
Electronic Unit are made to terminals beneath the Electronic
Unit. See Figure 2-7.
2.7 Sensing Element Connection (Continued)
GROUND
(GREEN)
COTE-SHIELD
(RED)
CENTER WIRE
(BLUE)
REMOVE
ELECTRONIC
UNIT TO ACCESS
SENSOR HARNESS
(2.5mm Hex-Head Screws)
Cable Fitting
(M20 AdapterOptional)
EQUIPOTENTIAL
TERMINAL
+
SHIELD WIRE MUST BE CLIPPED BY USER
CLIPPED SHIELD WIRE MUST NOT TOUCH CONDULET HOUSING
2 TERMINAL PROBE (TYP)
3 TERMINAL PROBE (TYP)
Ground Wire
(GREEN)
Ground Wire
(GREEN)
Center Wire
(BLUE)
Shield Wire
(CLIPPED)
Center Wire
(BLUE)
Shield Wire
(RED)

ThePoint™ Series Installation
13
2.8 Calibration
ThePoint™ level measurement switch features both Auto-
Cal and manual calibration. The standard Auto-Calibration
mode is applicable to most liquids and slurries point level
measurements. If preferred, the manual calibration can be
used and is recommended for some application. ThePoint
electronic unit has auto and manual calibration modes
built into the standard unit and can be accessed through
a simple routine (see section 2.8.5). The inclusion of these
calibration modes allows the Drexelbrook RF Point Level
Products application exibility that is far greater then any
other point level product on the market. This RF Point Level
switch can be used in Liquids, Solids, Slurries, and Interface
applications.
2.8.1 Selecting the Calibration Mode for your application.
The following table is a list of measurement types and the
recommended calibration mode for each of these applications.
ThePoint has eight calibration modes however; only four are
used on the majority of applications.
ThePoint will be shipped in the standard Auto-Cal mode #2
unless pre-ordered in a specic mode. To determine if the
ThePoint has been shipped in a mode other than #2, look
at the label on the inside of the unit housing. The model
number will start with PXL1. The “X” indicates the pre-set
mode typically an “L” for mode #2.
Common Calibration Modes
Mode 2 = L - Fixed Cal 2pF: 2pF differential, set point
locked 2pF above starting capacitance
Mode 6 = P - Fixed Cal 0.5pF: 0.5pF differential, set point
locked 0.5pF above starting capacitance
Mode 7 = M - Manual calibration standard sensitivity – pots
adjusts from 0 to 65pF
Mode 8 = G - Manual calibration High sensitivity – pot
adjusts from 0 to 27 pF
Additional calibration modes for specialty applications
(consult factory)
Mode # 1 = N
Mode # 3 = T
Mode # 4 = V
Mode # 5 = H
For explanation of mode See Section 2.8.5

ThePoint™ Series Installation
14
Application Guide
(For instructions on how to access alternate modes see 2.8.4)
2.8.1 Selecting the Calibration Mode for your application (Continued)
Application Calibration Mode
Liquids and Slurries Auto-Cal Mode #2
Granular /Solids with Bulk Density
greater than 20#’s per cubic foot
Manual Cal Mode #7
Granular/Solids with Bulk Density
Under 20#’s per cubic foot
Manual Cal Mode #8 (high
sensitivity)
Interface Measurement Manual calibration Mode #7
Plugged Chute Indication for Solids
(Bulk density greater than 20 #’s per
cubic foot)
Manual calibration Mode #7
Plugged Chute Indication for Solids
(Bulk density under 20 #’s per cubic foot)
Manual calibration Mode #8
(high sensitivity)
2.8.2 Using ThePoint with Auto-Calibration mode #2
After ThePoint is installed in the vessel, simply apply power.
ThePoint electronic unit will auto calibrate.
Caution
The material being measured must be below the sensing
element when power is applied (Sensing element uncovered).
Calibration is complete.
If power has been applied to ThePoint prior to installation
(on a test bench) or, if ThePoint is moved from one vessel to
another, RECAL is necessary for the unit to capture the new
air value.
Merely press and hold the RECAL button (shown in Figure 2-
8) for ve (5) seconds. After ve seconds, the two LED’s ash
for sixty seconds before reset occurs. [Remove power from
ThePoint while the LED’s are ashing and reset will occur
immediately upon next power up].
The Point is now ready for installation.