AMI MI982 User manual

MI982
Intel® H81 Based Mini-ITX board
Mini ITX Motherboard
USER’S MANUAL
Version 1.0

ii MI982 User’s Manual
Acknowledgments
AMI is a registered trademark of American Megatrends Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel and Intel® 4th Generation Core DC/QC Processor are
registered trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Fintek is a registered trademark of Fintek Electronics Corporation.
All other product names or trademarks are properties of their
respective owners.

MI982 User’s Manual iii
Table of Contents
Introduction .......................................................1
Product Description.............................................................1
Checklist..............................................................................1
MI982 Specifications...........................................................2
Board Dimensions................................................................4
Installations........................................................6
Installing the Memory...........................................................7
Setting the Jumpers...............................................................8
Connectors on MI982.........................................................14
BIOS Setup........................................................28
Drivers Installation......................................54
Intel Chipset Software Installation Utility..........................55
VGA Drivers Installation...................................................56
Realtek HD Audio Driver Installation ...............................57
LAN Drivers Installation...................................................58
Intel® Management Engine Interface..................................59
Intel® USB 3.0 Drivers .....................................................60
Appendix............................................................62
A. I/O Port Address Map...................................................62
B. Interrupt Request Lines (IRQ) .......................................63
C. Watchdog Timer Configuration .....................................64

iv MI982 User’s Manual
This page is intentionally left blank.

INTRODUCTION
MI982 User’s Manual 1
Introduction
Product Description
The MI982 Mini ITX motherboard is based on the latest Intel®H81
chipset. The platform supports Intel®4th Generation Core™DT i7/i5/i3
processors.Thelatest Intel®processors provide advanced performance in
both computing and graphics quality. This meets the requirement of
customersin the gaming, POS, digitalsignage and server market segment.
The platform supports two SO-DIMM sockets that can accommodate up
to16GB ofDDR3-1600 Non ECC memory. The Intel® 4th Gen. Core™
DT processor integrated HD graphics supports 3 independent displays,
Direct X 11.1, OpenGL3.2, and Open CL 1.2. Display interfaces are for
HDMI, DisplayPort and VGACRT.
With two Gigabit Ethernets, the MI982 Mini ITX board utilizes the
dramatic increase in performance provided Intel’s latest cutting-edge
technology. Expansion is provided by PCIe(16x), one full sized MiniPCIe
and a half sized MiniPCIe. Onboard connectors support 4x SATA III, 4x
or 6x USB 2.0 depending on the MI982 model and 6x COM ports. The
board measures 170mm x 170mm.
Checklist
Your MI982 package should include the items listed below.
The MI982 MINI ITX motherboard
This User’s Manual
1 CD containing chipset drivers and flash memory utility

INTRODUCTION
2 MI982 User’s Manual
MI982 Specifications
Model Name
MI982EF
Form Factor
Mini ITX
CPU Type
- Haswell Refresh 4th Generation Intel®CoreTM i7/i5/i3/Pentium DT
processor & FCLGA1150 package [37.5 mm x 37.5mm]
-TDP: 35W ~ 84W
CPU Speed
Up to 4.0GHz
Cache Size
Up to 8MB
CPU Socket
LGA1150 (Socket H3)
Chipset
Intel®H81 PCH
Package =23 mm x 22 mm, 0.65 mm ball pitch
BIOS
AMI BIOS
Memory
Haswell Refresh 4th Generation Intel®CoreTM DT processors integrated
memory controller,
-DDR3-1600 M[email protected]
-SO-DIMM x 2, Max. 16GB (Non-ECC)
VGA
Haswell Refresh 4th Generation Intel®DT processor integrated HD Gfx,
supports 3 independent displays, Direct X 11.1, OpenGL 3.2, Open CL
1.2
-DVI-D x 1 (Thru port C, with level shifter ASM1442K)
-DisplayPort x 1 (Thru port D)
-VGA x 1 (Thru PCH)
LAN
1. Intel® I217LM PHY GbE
2. Intel® I211AT PCIe GbE as 2nd LAN
USB
USB 2.0 host controller [H81 Integrated], support 8 ports
-4 ports via the rear panel I/O
-2 ports via MiniPCIe socket
-2 ports via pin-header
USB 3.0 host controller [H81 Integrated], support 2 ports
-2 ports via the rear panel I/O
Serial ATA
Intel®H81 PCH built-in SATA controller, support 4 ports
-2 x SATA III (6Gbps) + 2 x SATA II (3Gbps)
Audio
Intel®H81 PCH built-in High Definition Audio controller + Realtek
ALC892 w/ 7.1 channels
LPC I/O
Fintek F81866AD-I (128-pin LQFP [14mm x 14 mm])
-COM #1 (RS232/422/485) support ring-in with power @500 mA
(selectable for 5V or 12V) [EXAR SP339EER1 232/422/485
transceiver x 1 for jumper-less]
-COM #2~COM #6 (RS232 only)
Hardware Monitor (2 thermal inputs,4 voltage monitor inputs & 2 Fan
headers)
-CPU FAN x 1(PWN Fan type, 4-pin connector)
-SYS fan x 1(PWM Fan type, 4-pin connector)]
Digital IO
4 in & 4 out

INTRODUCTION
MI982 User’s Manual 3
Expansion
Slots
- PCI-Express (16x) x1 [Gen 2.0 PEG]
- Mini PCI-Express x 2 port [1 x Full-sized,1 x Half-sized] , both support
USB 2.0 signal
Edge
Connectors
Dual DB9 stack connector for COM #1 / #2
VGA + DVI-D stack connector x1
DisplayPort + dual USB (2.0) stack connector x1
RJ-45 + dual USB (3.0) stack connector x1
RJ-45 + dual USB (2.0) stack connector x1
Triplet type Jack 3x1 for Audio port [Line-in / Line-out / Mic-in]
Onboard
Header/Conn
ector
2 ports x SATA III [Blue color]
2 ports x SATA II
DF-11 2x4 header x 1 for 2 ports USB 2.0
DF-11 2x5 box header x 4 for COM 3/4/5/6 (RS232 only)
2x5 header for Digital IO
2x5 header for front Audio
2x4 header for front panel I/O (2.54 pitch)
2x2 pin ATXpower connector x1
1x ATXstandard 24-pin type for power connector
Watchdog
Timer
Yes (256 segments, 0, 1, 2…255 sec/min)
System
Voltage
ATX standard 24-pins type
4 pin type (+12V only)
Other
-LAN Wakeup
-EuP/ErP
-iSMART 3.0
Environment
Operation Temperature: 0~60 degree C
Storage Temperature: -20~80 degree C
Relative humidity: 0~90%, non-condensing
Board Size
170mm x 170mm
Operation
System
Windows 7, Windows 8, Linux

INTRODUCTION
4 MI982 User’s Manual
[
Board Dimensions

INSTALLATIONS
MI982 User’s Manual 5

INSTALLATIONS
6 MI982 User’s Manual
Installations
This section provides information on how to use the jumpers and
connectorsonthe MI982 in order to set up a workable system. The topics
covered are:
Installing the Memory......................................................................6
Setting the Jumpers .........................................................................7
Connectors on MI982....................................................................12

INSTALLATIONS
MI982 User’s Manual 7
Installing the Memory
The MI982 board supports two DDR3 memory modules for a maximum
total of 16GB in DDR3 SODIMM memory type.
Installing and Removing Memory Modules
To install the DDR3 modules, locate the memory slot on the board and
perform the following steps:
1. Hold the DDR3 module so that the key of the DDR3 module aligned
with that on the memory slot.
2. Gentlypush theDDR3module in anuprightpositionuntiltheclipsof the
slot close to hold the DDR3 module in place when the DDR3 module
touches the bottom of the slot.
3. To remove the DDR3 module, press the clips with both hands.
DDR3 Module
Lock
Lock
Lock
Lock

INSTALLATIONS
8 MI982 User’s Manual
Setting the Jumpers
Jumpers are used on MI982 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on MI982 and their respective functions.
Jumper Locations on MI982.............................................................9
JP1: COM2 RS232 RI/+5V/+12V Power Setting..............................11
JP2: COM1 RS232 RI/+5V/+12V Power Setting..............................11
JP4: Power Good Selection............................................................12
JP5: Flash Descriptor Security Override (Factory use only)...............13
JBAT1: Clear CMOS Contents.......................................................13

INSTALLATIONS
MI982 User’s Manual 9
Jumper Locations on MI982

INSTALLATIONS
10 MI982 User’s Manual
Jumpers on MI982.....................................................................Page
JP1: COM2 RS232 RI/+5V/+12V Power Setting..............................11
JP2: COM1 RS232 RI/+5V/+12V Power Setting..............................11
JP4: Power Good Selection............................................................12
JP5: Flash Descriptor Security Override (Factory use only)...............13
JBAT1: Clear CMOS Contents.......................................................13

INSTALLATIONS
MI982 User’s Manual 11
JP1: COM2 RS232 RI/+5V/+12V Power Setting
JP1
Setting
Function
Pin 1-3
Short/Closed
+12V
Pin 3-4
Short/Closed
RI
Pin 3-5
Short/Closed
+5V
JP2: COM1 RS232 RI/+5V/+12V Power Setting
JP2
Setting
Function
Pin 1-3
Short/Closed
+12V
Pin 3-4
Short/Closed
RI
Pin 3-5
Short/Closed
+5V
5 1
6 2
5 1
6 2

INSTALLATIONS
12 MI982 User’s Manual
JP4: Power Good Selection
JP4
Function
Short
Factory use only
Open
Normal
1 2

INSTALLATIONS
MI982 User’s Manual 13
JP5: Flash Descriptor Security Override (Factory use only)
JP5
Flash Descriptor Security Override
Open
Disabled (Default)
Close
Enabled
JBAT1: Clear CMOS Contents
JBAT1
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
1 2
3
1

INSTALLATIONS
14 MI982 User’s Manual
Connectors on MI982
Connector Locations on MI982 ......................................................15
CN1: COM1 and COM2 Serial Ports ..............................................17
CN2: VGA and DVI-D Connector ..................................................17
CN3: USB2.0 Connector ...............................................................18
CN4: DP Connector ......................................................................18
CN5: Gigabit LAN (Intel I217LM) / USB3.0 ...................................18
CN6, CN7, CN8, CN9: SATA Connectors......................................18
CN10: Gigabit LAN (Intel I211AT) / USB2.0..................................18
CN11: HD Audio Connector ..........................................................18
J1: ATX 12V Power Connector......................................................19
J4: ATX Power Supply Connector..................................................19
J7: Digital I/O................................................................................20
J9: Mini PCIE Connector...............................................................21
J10: Mini PCIE Connector .............................................................21
J11: SPI Flash Connector (Factory use only) ...................................22
J12: MCU Flash Connector (factory use only) .................................22
J13: Debug 80 Port Connector (factory use only).............................22
J14: Front Panel Function Connector ..............................................23
J15, J16, J17, J18: COM3/COM4/COM5/COM6 Connector.............24
J20: USB Connectors ....................................................................24
J22: Audio Front Header................................................................25
PCIE1: PCI-E X16 Slot.................................................................25
CPU_FAN1: CPU Fan Power Connector........................................26
SYS_FAN1: System Fan1 Power Connector ...................................26

INSTALLATIONS
MI982 User’s Manual 15
Connector Locations on MI982

INSTALLATIONS
16 MI982 User’s Manual