Amiko HD8140C SE User manual

1. Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4. Remote Control. . . . . . . . . . . . . . . . . . . . . . 4
5. Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . 6
6. Rear Panel. . . . . . . . . . . . . . . . . . . . . . . . . . 9
7. Connecting Your System . . . . . . . . . . . . . .11
8. Basic Operations . . . . . . . . . . . . . . . . . . . 15
8.1 Turn On Stb . . . . . . . . . . . . . . . . . . . . . 15
8.2 Power . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.3 Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.4 Pause . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.5 Recall . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.6 Favorite . . . . . . . . . . . . . . . . . . . . . . . . 15
8.7 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.8 Information . . . . . . . . . . . . . . . . . . . . . . 15
8.9 EPG . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.10 Tv/Radio . . . . . . . . . . . . . . . . . . . . . . . 16
8.11 Channel List . . . . . . . . . . . . . . . . . . . . 16
8.12 Sleep . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.13 Page Up/Page Down . . . . . . . . . . . . . 17
8.14 Text. . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.15 Subtitle . . . . . . . . . . . . . . . . . . . . . . . . 17
8.16 Find . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.17 Zoom . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.18 TV/Sat . . . . . . . . . . . . . . . . . . . . . . . . 17
8.19 Menu . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.20 Video Format . . . . . . . . . . . . . . . . . . . 17
8.21 Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
9. Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
9.1 Organizing Service . . . . . . . . . . . . . . . . 17
9.2 Organizing Favourites . . . . . . . . . . . . . 19
10. Installation. . . . . . . . . . . . . . . . . . . . . . . . 19
10.1 Satellite Installation. . . . . . . . . . . . . . 19
10.2 Fastscan Satellite . . . . . . . . . . . . . . . 20
10.3 Auto Installation . . . . . . . . . . . . . . . . 20
10.4 Satellite Guide . . . . . . . . . . . . . . . . . 20
10.5 Terrestrial Installation . . . . . . . . . . . . 21
10.6 Cable Installation . . . . . . . . . . . . . . . 21
11. System. . . . . . . . . . . . . . . . . . . . . . . . . . . 21
11.1 Language . . . . . . . . . . . . . . . . . . . . . 21
11.2 A/V Control . . . . . . . . . . . . . . . . . . . . 22
11.3 Ethernet Setting . . . . . . . . . . . . . . . . 22
11.4 Time Setting . . . . . . . . . . . . . . . . . . . 23
11.5 Timer . . . . . . . . . . . . . . . . . . . . . . . . . 23
11.6 Parental Control . . . . . . . . . . . . . . . . 24
11.7 Miscellaneous Settings . . . . . . . . . . . 24
11.8 Software Upgrade . . . . . . . . . . . . . . . 24
11.8.1 Upgrade By Usb. . . . . . . . . . . . . . . 24
11.8.2 Http Upgrade . . . . . . . . . . . . . . . . . 24
11.8.3 Ftp Upgrade . . . . . . . . . . . . . . . . . . 25
11.8.4 Upgrade By Rs232: . . . . . . . . . . . . 25
11.8.5 Backup To Usb. . . . . . . . . . . . . . . . 25
11.9 Default Setting . . . . . . . . . . . . . . . . . 25
11.9.1 Default Value:. . . . . . . . . . . . . . . . . 26
11.9.2 Delete All Channel: . . . . . . . . . . . . 26
11.9.3 Save Default Value . . . . . . . . . . . . 26
11.10 Information . . . . . . . . . . . . . . . . . . . 26
12. Conditional Access . . . . . . . . . . . . . . . . 26
12.1 Ca Setting. . . . . . . . . . . . . . . . . . . . . 26
12.2 Common Interface . . . . . . . . . . . . . . 26
13. Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
13.1 Record . . . . . . . . . . . . . . . . . . . . . . . 27
13.2 Movie . . . . . . . . . . . . . . . . . . . . . . . . 27
13.3 Music . . . . . . . . . . . . . . . . . . . . . . . . 27
13.4 Image . . . . . . . . . . . . . . . . . . . . . . . . 28
13.5 PVR Setting . . . . . . . . . . . . . . . . . . . 28
13.6 Disk Manage. . . . . . . . . . . . . . . . . . . 29
13.7 Remove Usb Device Safely!. . . . . . . 29
14. Application . . . . . . . . . . . . . . . . . . . . . . . 29
14.1 Youtube. . . . . . . . . . . . . . . . . . . . . . . 29
14.2 Rss Reader. . . . . . . . . . . . . . . . . . . . 30
14.3 Weather Forecast . . . . . . . . . . . . . . . 30
14.4 Google Maps . . . . . . . . . . . . . . . . . . 30
14.5 FTP. . . . . . . . . . . . . . . . . . . . . . . . . . 30
14.6 Web TV. . . . . . . . . . . . . . . . . . . . . . . 31
15. EPG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
16. New Features . . . . . . . . . . . . . . . . . . . . . 31
16.1 Time Shift . . . . . . . . . . . . . . . . . . . . . 31
16.2 Record . . . . . . . . . . . . . . . . . . . . . . . 31
17. Trouble Shooting . . . . . . . . . . . . . . . . . . 32
18. Specifications . . . . . . . . . . . . . . . . . . . . . 32
CONTENTS
European Union Directive on Waste Electrical and Electronic Equipment (WEEE)
This symbol applies to European countries only and indicates that the equipment carrying this mark must
NOT be thrown into trash. At the end of its useful life, always dispose of E-waste in a manner which is
consistent with local laws and regulations. For more information on the EU WEEE Directive, please see
http://ec.europa.eu/environment/waste/weee_index.htm

1. SAFETY
This HD Receiver has been manufactured to satisfy the international safety standards. Please read the following safety precautions
carefully.
MAINS SUPPLY: 100~240V AC, 50/60Hz
OVERLOADING: Do not overload wall outlet, extension cord or adapter as this may result in fire or electric shock.
LIQUIDS: Keep liquids away from the HD Receiver. The apparatus shall not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed on the apparatus.
CLEANING: Disconnect the HD Receiver from the wall outlet before cleaning .Use a light damp cloth (no solvents) to dust the HD
Receiver.
VENTILATION: The slots on top of the HD Receiver must be left uncovered to allow proper airflow to the unit. Do not stand the HD
Receiver on soft furnishings or carpets. Do not expose the HD Receiver to direct sunlight or do not place it near a heater. Do not
stack electronic equipments on top of the HD Receiver.
ATTACHMENTS: Do not use any attachments that are not recommended as these may cause hazard or damage the HD Receiver.
CONNECTION TO THE SATELLITE DISH LNB: Disconnect the HD Receiver from the mains before connecting or disconnecting
the cable from the satellite dish.
FAILURE TO DO SO CAN DAMAGE THE LNB.
CONNECTION TO THE TV: Disconnect the HD Receiver from the mains before connecting or disconnecting the cable from the
satellite dish.
FAILURE TO DO SO CAN DAMAGE THE TV.
EARTHING: The LNB cable MUST BE EARTHED to the system earth for the satellite dish.
LOCATION: Place the HD Receiver indoor in order not to expose to lightening, rain or sunlight.
2. INTRODUCTION
Thank you for purchasing the HD Receiver.
This HD Receiver is fully compliant with the international DVB standard and thus transmits digital images, sounds, information
guides and teletext directly to your TV through the satellite broadcasting.
Now you can comfortably see and receive digitally transmitted music, news, movie and sports satellite broadcasts in your office or
at your home. You can enjoy interesting games embedded in HD Receiver.
In service search section, both the automatic service search method and the manual search mode are provided. Also it supports
DiSEqC 1.0, 1.2 and USALS, enabling you to move your antenna in order to focus preferred satellite. You can save up to 6000 TV
and Radio services and work around with the favorite, Lock, Delete, Move and Sort functions.
The menu is very modern and supports multiple languages. All functions can be carried out using the remote control and some
of the functions can also be carried out using the front panel. The HD Receiver is easy to use and adaptable for future advances.
Please be aware that new software may change the functions of the HD Receiver.
If you have any difficulties concerning the operation of your HD Receiver, please refer to the relevant section of this manual, includ-
ing the ‘Troubleshooting’. This Manual will provide you with useful information on using the HD Receiver.
3. FEATURES
● MPEG-Fully DVB-S / DVB-S2 (H.264) HD compliant
● 6000 channels (TV and Radio) programmable
● Multilingual menu text support
● Channel switching time less than 1 second
● Channel list editing
● Favorite channel list editing
● True-color On-Screen Display (OSD)
● Full Picture In Graphic (PIG) function
● Electronic Program Guide (EPG) for on screen channel information
● Subtitle supported
● Teletext supported by VBI insertion and software emulation
● Parental lock facility by channel and program event
● Program and Channel information transfer from receiver to receiver
● Exciting games embedded
● Dolby Digital Bit-Stream output via HD OUT
● DiSEqC 1.0, 1.1, 1.2 ,USALS and Unicable
● Full HD (1080p) Video/Audio Output
● 2x USB 2.0 Host
● RTC (Real-Time-Clock)
● Time Shift
● Video Recording
● Recording one channel and Time Shifting another channel (optional)
● 3G Network Function Supported
3
USER’S MANUAL

4. REMOTE CONTROL
(AMIKO HD8140C SE / HD8142 / HD8155 / HD8265+ / MINI HD265 / MINI
COMBO EXTRA / MIRA WIFI / IMPULSE T2C)
You can power on/off the receiver, operate on screen menu, and use a variety of
hot key function.
POWER To switch your receiver on from standby or standby to on.
MUTE Used to enable or disable the audio
NUMERIC KEYS Used to select channels or enter programming parameters
TV / RADIO Receiver switches between TV and Radio mode.
(ZOOM) Press key select zoom times, from X1 to X16.
RECALL Return to the previous menu or status.
TV/SAT Receiver switches between TV and receive mode.
INFO To display channel status or various program information of current service.
EPG (Electronic Program Guide) Display the Programs guide on screen when
available.
MENU Displays the Main Menu on the screen, or return to the previous menu or
status.
EXIT Cancel the user selection and return to the viewing mode from a menu.
OK To select menu option, or to updated on entry.
◄/► KEY To adjust volume level, or to move cursor left or right in the menu.
▼/▲ KEY To change channels, or to move cursor up or down in the menu.
PAGE
► /PAGE ► To move up the cursor to the next or previous page in the
menu or channel list.
G REC Has different functions per menu.
Teletext Shows teletext information of the current channel supports.
Subtitle Subtitle Display.
UHF In case your TV is connected through RF Modulator (UHF), select output
channel number between CH21 and CH69 with up and down key.
(FIND) Use to prompt find channels sort by character.
TIMER Press timer key you can setup up the Standby time.
V.FORMAT Press V.FORMAT button to switch the display mode among „AUTO”,
„By Native TV”, ”480p”, „576P”, „720P_50”, ”720P_60, ”1080i_50”, ”1080i_60” ,
”1080P_50” and ”1080P_60”
FAV (FAVORITE) To set receiver to the favorite server mode, display the favorite
channel.
FOLDER Press this button to enter the Record Manager menu directly.
AUDIO (Red Key) Audio channels setup, to select audio mode; Left, Right ,
Stereo, Mono.
OPTION (GREEN KEY) Shows NVOD information of the current channel supports.
SAT Display the satellite list at normal picture.


Play Mode Select the play mode in MP3 or JPEG player.
USB To remove the USB Hard Disk safely.
TMS (Time Shift) Press this button to display Time Shift info bar.
► Play To play the MP3, JPEG, or Record files.
Stop To stop the Time Shift, recording, or MP3/JPEG player.
II PAUSE Used to select the freeze function. Press once to freeze the screen
picture.
◄◄ FB To start Fast Backward function.
►► FF To start Fast Forward function.
◄I SB To start Slow Backward function.
I ► SF To start Slow Forward function
◄◄/ ►► I PREV/NEXT Switch to preview or next file in play mode
4
USER’S MANUAL

5
USER’S MANUAL
(AMIKO T60 / T70)
POWER To switch your receiver on from standby or standby to on.
MUTE Used to enable or disable the audio
NUMERIC KEYS Used to select channels or enter programming parameters
TV / RADIO Receiver switches between TV and Radio mode.
(ZOOM) Press key select zoom times, from X1 to X16.
(RECALL) Return to the previous menu or status.
(AUDIO) Audio channels setup, to select audio mode; Left, Right , Stereo, Mono.
INFO To display channel status or various programme information of current
service.
EPG (Electronic Programme Guide) Display the Programmes guide on screen
when available.
MENU Displays the Main Menu on the screen, or return to the previous menu or
status.
EXIT Cancel the user selection and return to the viewing mode from a menu.
OK To select menu option, or to updated on entry.
VOL-, VOL+ KEY To adjust volume level, or to move cursor left or right in the
menu.
CH-, CH+ KEY To change channels, or to move cursor up or down in the menu.
PAGE+/PAGE- To move up the cursor to the next or previous page in the menu or
channel list.
Red Key Has different functions per menu.
TTX (GREEN KEY) Shows teletext information of the current channel supports.
SUBTITLE (YELLOW KEY) Subtitle Display.
(FIND) Use to prompt find channels sort by character.
FAV (FAVOURITE) To set receiver to the favourite server mode, display the
favourite channel.
Archive Press this button to enter the File Manager menu directly.
► Play To play the MP3, JPEG or recording file, or start timeshift function.
Stop To stop MP3/JPEG player, recording file , Time Shift, or playback.
G Record To start recording.
◄◄ Fast Backward To start Fast Backward function.
►► Fast Forward To start Fast Forward function .
V.FORMAT Press VFORMAT button to switch the display mode among „Auto-> by
native TV<->1080i->1080p etc.
TV/STB Receiver switches between TV and receive mode.

6
USER’S MANUAL
5. FRONT PANEL
AMIKO HD8140C SE
AMIKO HD8142
AMIKO HD8155
AMIKO HD8265+
STANDBY KEY: To switch the receiver power on/stand by.
MENU KEY: To enter the Main Menu.
OK KEY: To see TV/Radio channel list, or to confirm in the menu.
V-/V+ KEY: To adjust volume level, or to move cursor left or right in the menu.
CH-/CH+ KEY: To change channels, or to move cursor up or down in the menu.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One CA Interface for Conax.
Display: (LED type) Indicates operating status of receiver.
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
USB: USB 2.0 Host, connect to USB hard disk, flash disk, WiFi dongle, 3G dongle. (On the right side of the receiver)
Display: (LED type) Indicates operating status of receiver.
POWER KEY: To switch the receiver power on/stand by.
CH-/CH+ KEY: To change channels, or to move cursor up or down in the menu.
Card Slot: One slot CA Interface for Conax Smartcard (on left side).
POWER KEY: To switch the receiver power on/stand by.
MENU KEY: To enter the Main Menu.
OK KEY: To see TV/Radio channel list, or to confirm in the menu.
V-/V+ KEY: To adjust volume level, or to move cursor left or right in the menu.
CH-/CH+ KEY: To change channels, or to move cursor up or down in the menu.
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One CA Interface for Conax.
USB A: USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
Display: (LED type) Indicates operating status of receiver.
POWER KEY: To switch the receiver power on/stand by.
MENU KEY: To enter the Main Menu.
OK KEY: To see TV/Radio channel list, or to confirm in the menu.
LEFT/RIGHT KEY: To adjust volume level, or to move cursor left or right in the menu.
UP/DOWN KEY: To change channels, or to move cursor up or down in the menu.
Remote Sensor: Detects infrared signal from remote control unit.

USER’S MANUAL
AMIKO MINI HD265
AMIKO MINI COMBO EXTRA
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One CA Interface for Conax.
USB (on the side): USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
Display: (LED type) Indicates operating status of receiver.
RS 232 (on the side): This is used to connect your receiver to a computer through a serial cable.
IR IN( on the side): Connect an External IR-Sensor (Infrared).
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One CA Interface for Conax.
Common Interface: One socket for Conditional Access Modules CAM.
USB A: USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
Display: (LED type) Indicates operating status of receiver.
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One CA Interface for Conax.
USB (On the side): USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
Display: (LED type) Indicates operating status of receiver.
AMIKO MIRA WIFI
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One CA Interface for Conax.
USB (On the side): USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
Display: (LED type) Indicates operating status of receiver.
7

8
USER’S MANUAL
AMIKO IMPULSE T2C
AMIKO T60
AMIKO T70
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One CA Interface for Conax. Under the receiver.
USB: USB 2.0 Host, connect to USB hard disk, or flash disk (on the right side of the receiver).
Display: (LED type) Indicates operating status of receiver.
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
USB: USB 2.0 Host, connect to USB hard disk, or flash disk (on the right side of the receiver).
Display: (LED type) Indicates operating status of receiver
Buttons: (Standby, CH-, CH+, V-, V+) to operator the receiver.
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
USB: USB 2.0 Host, connect to USB hard disk, or flash disk (on the right side of the receiver).
Display: (LED type) Indicates operating status of receiver
Buttons: (Standby, CH-, CH+) to operator the receiver.

6. REAR PANEL
9
USER’S MANUAL
AMIKO HD8140C SE
AMIKO HD8142
AMIKO HD8155
RF IN: This port is to connect the coaxial cable from Cable Antenna.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
USB: USB 2.0 Host, connect to USB hard disk, or flash disk,and wifi dongles.
TV: This is used to connect your TV through SCART cable.
DV OUT: Audio and Video output socket for TV set with DV OUT Input Jack only.
RS 232 SERIAL PORT: This is used to connect your receiver to a computer through a serial cable.
Ethernet: Network port, you can get a new software updates from this port.
POWER ON/OFF SWITCH: To switch ON/OFF the receiver power supply.
RF IN: This port is to connect the coaxial cable from Cable Antenna.
Ethernet: Network port, you can enjoy the network application function via this port, or you can get new software updates or new
games.
HD OUT: Audio and Video output socket for TV set with HDMI Input Jack only.
RS 232 SERIALPORT: This is used to connect your receiver to a computer through a serial cable.
VIDEO: This RCA connector is used to connect any external video.
AUDIO R/L: These RCA connectors are used to connect any external audio amp or system.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
HDD: To connect internal HDD.
DC 12V: This is used to connect an external 12V adapter.
Please refer to the diagram above for all possible connections of your receiver
Do not connect the unit to the mains socket until all other connections have been made and checked.
LNB IN 13/18V 400mA MAX: This port is to connect the coaxial cable from LNB of your Dish.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
HDMI: Audio and Video output socket for TV set with HDMI Input Jack only.
RS 232: This is used to connect your receiver to a computer through a serial cable.
Ethernet: Network port, you can get a new software updates from this port.
TV: This SCART connector is used to connect TV using SCART cable.
POWER ON/OFF SWITCH: To switch ON/OFF the receiver power supply.
USB: USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
AMIKO HD8265+
Please refer to the diagram above for all possible connections of your receiver
Do not connect the unit to the mains socket until all other connections have been made and checked.
LNB IN 13/18V 400mA MAX: This port is to connect the coaxial cable from LNB of your Dish.
RF IN: This port is to connect the coaxial cable from Terrestrial/Cable Antenna.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
USB B: USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
AV OUT: This RCA connector is used to connect any external video and audio.
HD OUT: Audio and Video output socket for TV set with HDMI Input Jack only.
RS 232 SERIAL PORT: This is used to connect your receiver to a computer through a serial cable.
Ethernet: Network port, you can get a new software updates from this port.
IR IN: Connect an External IR-Sensor (Infrared).
DC 12V: This is used to connect an external 12V adapter.

10
USER’S MANUAL
AMIKO MINI COMBO EXTRA
AMIKO IMPULSE T2C
AMIKO MINI HD265
AMIKO MIRA WIFI
Please refer to the diagram above for all possible connections of your receiver
Do not connect the unit to the mains socket until all other connections have been made and checked.
LNB IN 13/18V 400mA MAX: This port is to connect the coaxial cable from LNB of your Dish.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
HD OUT: Audio and Video output socket for TV set with HDMI Input Jack only.
Ethernet: Network port, you can get a new software updates from this port.
RCA: This RCA connector is used to connect TV using AV cable.
DC 12V: This is used to connect an external 12V adapter.
Please refer to the diagram above for all possible connections of your receiver
Do not connect the unit to the mains socket until all other connections have been made and checked.
LNB IN 13/18V 400mA MAX: This port is to connect the coaxial cable from LNB of your Dish.
RF IN: This port is to connect the coaxial cable from Terrestrial/Cable Antenna.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
HD OUT: Audio and Video output socket for TV set with HDMI Input Jack only.
RS 232: This is used to connect your receiver to a computer through a serial cable.
Ethernet: Network port, you can get a new software updates from this port.
AV OUT: This RCA connector is used to connect TV using RCA cable.
IR IN: Connect an External IR-Sensor (Infrared).
DC 12V: This is used to connect an external 12V adapter.
Please refer to the diagram above for all possible connections of your receiver
Do not connect the unit to the mains socket until all other connections have been made and checked.
LNB IN 13/18V 400mA MAX: This port is to connect the coaxial cable from LNB of your Dish.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
HD OUT: Audio and Video output socket for TV set with HDMI Input Jack only.
TV: This SCART connector is used to connect TV using SCART cable.
IR IN: Connect an External IR-Sensor (Infrared).
DC 12V: This is used to connect an external 12V adapter.
DC 5V:This is used to connect an external 5V adapter.
TV: This is used to connect your TV through SCART cable.
HDMI: Audio and Video output socket for TV set with HDMI Input Jack only.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
RF IN: This port is to connect the coaxial cable from Terrestrial/Cable Antenna.
AV OUT: This RCA connector is used to connect TV using RCA cable.

11
USER’S MANUAL
AMIKO T60
AMIKO T70
DC 5V:This is used to connect an external 5V adapter.
TV: This is used to connect your TV through SCART cable.
HD OUT: Audio and Video output socket for TV set with HDMI Input Jack only.
RF IN: This port is to connect the coaxial cable from Terrestrial/CableAntenna.
DC 5V: This is used to connect an external 5V adapter.
TV: This is used to connect your TV through SCART cable.
HD OUT: Audio and Video output socket for TV set with HDMI Input Jack only.
RF IN: This port is to connect the coaxial cable from Terrestrial/CableAntenna.
7. CONNECTING YOUR SYSTEM
There are two ways to connect the receiver to your existing TV system. We recommend using one of the following cases for the
best result:
1. If you have a high definition television set, you should use a HDMI cable for best result, Plug one end of the cable into the HD
OUT socket on the receiver, and the other end into the matching socket on your television. In this case, you do not have to make
audio connections because the HDMI connector can output stereo audio or Dolby Digital audio.
2. Connect one end of RCA cable to the RCA jack on the back of the receiver and the other end to a RCA jack on your TV.
AMIKO HD8140C SE
AMIKO HD8142

12
USER’S MANUAL
AMIKO HD8155
AMIKO HD8265+
AMIKO MINI HD265

13
USER’S MANUAL
AMIKO
MINI COMBO
EXTRA
AMIKO IMPULSE T2C
AMIKO MIRA WIFI

14
USER’S MANUAL
AMIKO T60
AMIKO T70

8. BASIC OPERATIONS
8.1 TURN ON STB
First, open the power switch to turn on the unit.
When the STB is first used, there will play the first channel from
the default Channel List. If the STB is not first used, STB will
play the same channel as last time before turning off.
8.2 POWER
1. Press [Power] Key can enter the Standby state
2. In Standby state, press [Power] Key again can call back the
unit and go on play the previous channel
3. User can also disconnect the device’s main power to end the
Standby state.
8.3 MUTE
1. Press [MUTE] key to mute the sound and the screen will
show up mute OSD.
2. Press [MUTE] key again to restore sound.
8.4 PAUSE
1. In playing mode, press [Pause] key, the picture will be
paused, but the sound of the channel will still continues.
2. Press [Pause] key again, the screen’s picture will skip over to
the current playing picture, and the sound of the channel will
corresponding playing.
8.5 RECALL
Press [RETURN] key will directly switch to the previous channel
that you played before current channel.
8.6 FAVORITE
1. In full screen, press [FAV] key, it will display a window of
”Favorite list” on the left of the screen, which you can watch
like below.
2. In the window of ” Favorite list ”, you can move highlight by
press [Channel Up/Channel Down] key to select favorite
Channels.
3. In the window of ” Favorite list ”, you can press [Left/Right]
key to select favorite groups Pressing [P-/P+] keys can imple-
ment the ”Page up/Page down” function
4. Press [Exit] key to exit the current window.
8.7 AUDIO
1. In full screen, press [AUDIO] key can open the ”Audio” win-
dow on the screen.
2. You can modify the audio track by press [Channel Up /
Channel Down] key and modify the audio mode by press[left/
right] key.
3. Mode: Left/Right/Stereo/Mono
8.8 INFORMATION
In full screen, press [INFO] key (press [INFO] key and [RED]
key) can open information screen, in the window shows the
parameters of current channel.
8.9 EPG
1. The STB has an Electronic Program Guide (EPG) to help you
navigate channels through all the possible viewing options.
The EPG supplies information such as channel listings and
starting and ending times for all available channels. Press
[EPG] key to display EPG screen.
2. Press [Red] key can select the channels by different group,
such as by Favorite/Satellite/Provider/CAS etc.
3. Press [Green] key to select different display mode among
Now EPG, Next EPG, More and Schedule, like the following
picture:
15
USER’S MANUAL

4. Press [Yellow] key in EPG menu can set one record timer or
go to Timer List menu.
5. In EPG menu, when you select one event by high light item,
you can set this event to record timer list directly by press
[REC] button.
6. In EPG menu, press [Exit] to close EPG screen.
8.10 TV/RADIO
In TV mode, pressing [TV/RADIO] key can switch to Radio
mode. In Radio mode, press [TV/RADIO] key to switch to TV
mode.
8.11 CHANNEL LIST
1. In full screen, press [OK] key can enter ”Channel List”.
2. Press [Red] key to change the different group. Which you can
watch like below.
3. Press [Green] key to display details information for EPG Now.
4. Press [Yellow] key you can change the current channel’s
property, such as FAV/ Lock/ Skip/ Delete/ Rename.
5. Press [Blue] key can open the ”Sort” window like below.
There are five kinds of sorting ways. You can press [Channel
Up/Channel Down] key to move highlight and press [OK] key
to confirm you selection.
6. The five kinds of sorting way are:
• Default: Sorting by scanning result.
• FTA/$: Sort channel through free and scramble sequence.
Free channel will in the front of channel list and scramble
channel will at the rear of channel list
16
USER’S MANUAL

• Lock: Accumulated all locked channels and list in the last of
TV Channel List.
• Name (A-Z): Sorting in Alphabetical Order, ignore ”$” symbol.
• Name (Z-A): Sorting in Alphabetical Order, ignore ”$” Symbol.
7. Press [Up/Down] key to move highlight and press [OK] key to
play the highlighted channel.
8. Press [Page Up/Down] key to page up and page Down.
9. Press [Exit] key to exit the channel list.
8.12 SLEEP
1. This function can set sleep timer. When you set a sleep timer
and the time arrive, the system will enter to standby automati-
cally.
2. Pressing [SLEEP] key, it will switch the mode between Sleep
Timer Off /10/30/60/90/120 minutes.
8.13 PAGE UP/PAGE DOWN
In Channel list, press [Page+/Page-] key can page up and page
down the channel list.
8.14 TEXT
1. Press [TTX] key in full screen, you can open teletext page on
the channel which has teletext information.
2. If the channel has no teletext information, it will show ”No
Teletext Data” on the screen.
8.15 SUBTITLE
1. Press [SUBTITLE] key in full screen you can select the subti-
tle language or off on the channel which has subtitle.
2. If you set the Auto subtitle option as ON in Miscellaneous set-
tings menu, the subtitle will be showed automatically.
8.16 FIND
1. Press[Find] key in full screen can open the ”Find” window like
above. You can press[Up/Down/left/right ]key to move high-
light and press[OK]key to input the selected symbol or letter
into the dialogue.
2. After input each character, the program list on the left will
search the channel according your input, and list the matched
channel.
3. Move highlight to ”OK” and press [OK] key can close ”Find”
window and you can select channel from the channels list
directly.
8.17 ZOOM
1. The [ZOOM] key allows you to magnify a certain area on the
images
2. Press [ZOOM] key again, the image will enlarge rotate as x1,
x2, x4, x6, x8, x12, x16.
3. In ”x2 ~ x16” image, using [Up/ Down/ Up/ Down] keys to
move the image center area you want to see.
4. In zoom mode, press [Exit] to close ”Zoom” window.
8.18 TV/SAT
Press [TV/Sat] key can switch between TV mode and STB
mode
8.19 MENU
Press [MENU] key can open the menu, exit the current menu to
last menu or close the window.
8.20 VIDEO FORMAT
Press [V. Format] key under Full Screen playback for 1st, it
will show the current system outputting video resolution, con-
tinuously press this key, system will switch its outputting video
resolution by sequence ” 480i-> 480P-> 576i-> 576p-> 720P->
1080i->1080p”.
8.21 EXIT
1. Press [EXIT] key can exit the current menu to last menu or
close the window.
9. SERVICE
When you press [Menu] key to enter menu, there will display the
picture like below:
1. Press[Left/Right] key you can select the submenu of
Organizing services and Organizing favourites.
2. Press [OK] key to enter the ”Organizing Service”. If Menu
Lock is ”On”, it will display an dialogue for user to key in
password. The default Password is ”0000”.
3. Press [Menu] key to go back to main menu.
9.1 ORGANIZING SERVICE
When you enter to ”Organizing Service” menu, there will display
the screen like below.
1.
You can move highlight by press [Channel Up/Channel Down]
key and [OK] key to select the programs which you want to edit.
2. You can press [Page Up/Page Down] key to implement the
Page Up/Page Down function.
3. You can use [Red] key to switch different Group.
4. You can press [Green] key to select the programs by different
select mode.
17
USER’S MANUAL


5. Press color key can implement the corresponding function in
”Organizing Services”.
Groups

1. Press [Red] key can open the ”Groups” window like above
2. You can press [Up/Down] key to move highlight and press
[OK] key to select group.
3. Press [Menu] key to close ”Groups” List.
Options
1. Press [Green] key can open the ”Options” window like above.
2. You can press [Up/Down] key to move highlight and press
[OK] key to confirm the select mode.
3. Press [Menu] key to close ”Options” List.
Move
1. Select the channels which you want to edit in channel list by
press [OK] key or other select mode.
2. Then press [Right] key to move the high light to right toolbar.
3. Select Move icon by press [Channel Up/Channel Down] key
and [OK] key.
4. Move the channels to the position which you want and press
[OK] key to confirm. Like the following picture:

Lock
1. Select the channels which you want to edit in channel list by
press [OK] key or other select mode.
2. Then press [Right] key to move the high light to right toolbar.
3. Select Lock icon by press [Channel Up/Channel Down] key
and [OK] key.
4. Lock the channel by press [OK] key. Like the following pic-
ture:
Delete
1. Select the channels which you want to edit in channel list by
press [OK] key or other select mode.
2. Then press [Right] key to move the high light to right toolbar.
3. Select Delete icon by press [OK key to delete channel one
by one.
4. When you high light in channel list ,you can press [OK] key
to select more channels ,and repeat b and c step to deleted.
Skip and rename
Follow the same way you can set the channel’s Skip or give the
new name for high light channel.
Find
1. Press[Find] key can open the ”Find” window like above.
You can press[Up/Down/left/right]key to move highlight and
press [OK] key to input the selected symbol or letter into the
dialogue.
2. After input each character, the program list on the left will
search the channel according your input, and list the matched
channel.
18
USER’S MANUAL

3. Move highlight to ”OK” and press [OK] key can close ”Find”
window and you can select channel from the channels list
directly.
9.2 ORGANIZING FAVOURITES
This menu is helpful in adding and deleting services to and from
the favorite group.

1. FAV List
To choose the FAV List by press ”FAV” button.
2. Add
To add services into favorites, Mark the desired services by
press ” OK ” button in Service List, press ► to choose Add
mode and press ” OK ” button.
3. Remove
To remove services from favorites, Mark the desired services by
press ” OK ” button in Favorite List, press
◄ to choose Remove
mode and press ” OK ” button.
4. Move
You can reorder and move the service to the preferred position
in Favorite List.
5. Rename
Select the desired FAV List by press ”FAV” button, using
◄/► ,
buttons to choose Rename mode and press ” OK ” button to
display keyboard, and rename it.
6. Group, Options and Find functions
Please refer to the ”Organizing Services” part in this manual.
10. INSTALLATION
1. Press [Left/Right] key to select menu pages among Satellite
Installation,FastScan Satellite,Auto installation,Satellite
Guide,Terrestrial Install,Cable Installation.
2. Press [OK] key to enter the ”Installation”. If Menu Lock is
”On”, it will display an dialogue for user to key in password.
The default Password is ”0000”.
3. Press [Up/ Down] key to select menu items. Press [menu]
key to go back to main menu.
10.1 SATELLITE INSTALLATION
Satellite
1. Satellite: Press[OK]key to enter the Satellite list.
2. Press [Up/ Down] key to select satellite. Press [Page] key to
page up or page down.
LNB Type
In this item, press[Left/Right]key can switch among ”Standard”,
”User” and ”Universal” , ”Unicable” mode.
DiSEqC
DiSEqC: You can press [OK] and [Up/ Down] key to switch
options. There are several options for your selection:
19
USER’S MANUAL

a) Disable: without DiSEqC.
b) 1/2, 2/2: two ports DiSEqC
c) 1/4, 2/4, 3/4, 4/4: 4 ports DiSEqC
d) 1/8, 2/8… 8/8: 8 ports DiSEqC
e) 1/16, 2/16….16/16: 16 ports DiSEqC
Positioner
Positioner In ”Positioner” item, you can press [Left/Right]key
to switch ”Off / DiSEqC 1.2 / USALS” functions.
22K
You can use [Volume Up/ Volume Down] key to switch ”ON /
Off”. When this item is switched to ”ON”, receiver will receive TV
and radio input signal from 22K port. If the item is switched to
”Off”, the receiver will receive all signal from 0K port.
! Notice: When you choose LNB type ”Universal”, you can not
modify 22K.
Polarity
In ”Polarity” item, [Left/Right]key to switch ”Auto / H / V” func-
tions.
LNB Power
In ”LNB POWER” item, you can press [Left/Right] key to switch:
” On/Off” functions.
TP Edit
When you enter to ”TP Edit” menu, there will display the screen
like below:
1. In ”Satellite” item, press[Left/Right]key to switch satellite that
you want to scan or press[OK]key to enter satellite list for
selection.
2. In ”TP Index” item, you not only can use [Left/Right]key to
select transponder but also can use [Add] and [Delete] func-
tions.
• When you press[Green] key, it will display ”New TP” in ”TP
Index” item; You should set the parameters of ”TP Frequency”
and ”Symbol Rate” for this new transponder. The param-
eters of ”TP Frequency” and ”Symbol Rate” can set by num-
ber keys. The available range are ”3000~13450 MHz” and
”1000~45000Ks/s”.
• When you press[Yellow] key, there will show up a warning
message for reminding whether you will delete the current
transponder or not. If you select ”Yes”, the current transponder
will be deleted, and the total account of transponder will
reduce 1 correspondingly.
• When you press [Blue] key, there will show up a warning mes-
sage for reminding whether you will delete all transponders or
not. If you select ”OK”, all transponders will be deleted.
3.
For the existed transponder, you also can use number keys to
modify the parameters of ”TP Frequency” and ”Symbol Rate”.
4. When you complete your modification, Press [Red] key, it will
show up a dialog to ask you scan mode, program type, scan
type and NIT Search on/off. After you set up, press [OK] key
to start scanning.
5. In the ”TP Scan” item, press [Exit] key to exit the scanning
and save the current parameters.
Single Scan
1. Press [Red] key, it will show up a dialog to ask you scan
mode (means you want to scan all channels or only scan
free channels), program type (means you want to scan all
channels or only scan TV/Radio channels), scan type (means
preset scan, that is searching the existed TP. Automatic
Scan means blind scan. It is no need existed TP info) and
NIT Search on/off. After you set up, press [OK] key to start
scanning.
2. Press [White] key into the blind scanning immediately.
TP Scan
Press [Green] key to scan current TP’s programs.
Auto DiSEqC
Press [Blue] key to run Auto DiSEqC function, it can find the
satellite connect to which port automatically.
Blind Scan
Press [White] key can directly into blind scan mode to scan the
current satellite.
10.2 FASTSCAN SATELLITE
In this menu, you can search the channels fast by select the
provider and press OK button on Start Search item.
10.3 AUTO INSTALLATION
”Auto Installation” is a very new and convenient function. It will
automatically detect all dishes connecting to this machine and
scan the available services belonging to the satellite matched
according to satellites and transponders data in current data-
base. You don’t have to input any parameter of your antenna
settings. Just press ” OK ” button to enter this ”Auto Installation”
menu then it starts scanning and shows you the result at the
end of scanning.
10.4 SATELLITE GUIDE
When you enter to ”Satellite Guide” menu, you will see the
screen like below:
20
USER’S MANUAL