Amit RB-MVB/AN02 User manual

rb-mvban02_g_en_100
RB-MVB/AN02
MVB analyser
Operation manual
Version 1.00

RB-MVB/AN02
rb-mvban02_g_en_100 2/30
AMiT, spol. s r. o. does not provide any warranty concerning the contents of this
publication and reserves the right to change the documentation without
obligation to inform any body or authority about it.
This document can be copied and redistributed under following conditions:
1. The whole text (all pages) must be copied without any changes.
2. All redistributed copies must retain the AMiT, spol. s r. o. copyright notice
and any other notices contained in the documentation.
3. This document must not be distributed for purpose making of profit.
The names of products and companies used herein can be trademarks or
registered trademarks of their respective owners.
AMiT is a registered trademark.
Copyright (c) 2016, AMiT, spol. s r. o.
Producer: AMiT, spol. s r. o.
Naskové 1100/3, 150 00 Praha
www.amit-transportation.com
Technical support: [email protected]

RB-MVB/AN02
3/30 rb-mvban02_g_en_100
Contents History of revisions.........................................................................................4
Related documentation...................................................................................4
1. Definition of used abbreviaions .........................................................5
2. Definition of used terms......................................................................6
3. Introduction..........................................................................................7
4. Technical parameters..........................................................................8
4.1. Dimensions...................................................................................................10
4.2. Recommended drawing symbol ...................................................................11
5. Product marking ................................................................................12
5.1. Producer type label.......................................................................................13
6. Conformity assessment ....................................................................14
6.1. Other tests....................................................................................................15
7. Power supply......................................................................................16
8. Communication lines.........................................................................17
8.1. MVB-ESD.....................................................................................................17
8.2. MVB-EMD ....................................................................................................18
8.2.1 MVB line state indication..............................................................................19
8.3. Ethernet........................................................................................................20
8.3.1 Ethernet line state indication ........................................................................21
9. Inputs/outputs....................................................................................22
9.1. Trigger output...............................................................................................22
10. Indications and settings....................................................................23
10.1. System LEDs................................................................................................23
10.2. Service mode and factory setting .................................................................24
10.3. Mounting, installation rules...........................................................................25
11. Ordering information and completion .............................................26
11.1. Completion ...................................................................................................26
12. Packing ...............................................................................................27
13. Storing.................................................................................................28
14. Maintenance .......................................................................................29
15. Waste disposal...................................................................................30

RB-MVB/AN02
rb-mvban02_g_en_100 4/30
History of revisions
Document name: rb-mvban02_g_en_100.pdf
Revision
Date
Author of change
Changes
100
4. 10. 2016
Petrovský J.
New document
Related documentation
1. RB-MVB/AN02 –MVB analyser –Programmers manual
file: rb-mvban02_1_ms_en_100.pdf

RB-MVB/AN02
5/30 rb-mvban02_g_en_100
1. Definition of used abbreviaions
Bus Administrator
Electrical Middle Distance
Medium Attachment Unit
Multifunction Vehicle Bus
Message Data
Process Data
To Be Defined
Train Communication Network
BA
EMD
MAU
MVB
MD
PD
TBD
TCN

RB-MVB/AN02
rb-mvban02_g_en_100 6/30
2. Definition of used terms
Bus Administrator
MVB device with Bus Administrator functionality is able to work as MVB bus
Master. This function supposes the device is able to transfer the process data
and reports as well as transmit and receive the Device Status type information.
Electrical Middle Distance
This is a type of physical interface of MVB line, where a twisted pair of shielded
wires is used for interconnection with implementing of transformer coupling for
galvanic isolation. EMD medium is used for up to 32 nodes and for distances to
200 m.
Electrical Short Distance
Type of physical interface of the MVB line, with shielded twisted pair, used for
connection. Usage of galvanic isolation is not a mandatory, but some
implementations offer possibility of galvanic isolation. ESD medium is used for
up to 32 nodes on up to a distance of 20 m.
TCN Gateway
MVB device with TCN Gateway function is able to access to other buses. This
function supposes the device is able to transfer the process data and reports as
well as transmit and receive the Device Status type information.

RB-MVB/AN02
7/30 rb-mvban02_g_en_100
3. Introduction
RB-MVB/AN02 is an MVB analyser. Analyser contains doubled MVB interface
in ESD and EMD connection, Ethernet interface and BNC connector for
triggering.
Device is supplied from factory only with loader. Before first use all required
domains must be loaded into device (see Programming manual).
2 × MVB interface (in EMD and ESD version, doubled line)
1 × Ethernet 10/100 Mbps interface, RJ45
1 ×output trigger with BNC connector
Power supply voltage 24 V DC
Design according to EN 50155:2007
MVB interface complies with IEC 61375-3-1: 2012
Basic features

RB-MVB/AN02
rb-mvban02_g_en_100 8/30
4. Technical parameters
MVB Standard
IEC 61375-3-1: 2012
Number of MVB lines
1 × EMD, 1 × ESD
Number of MVB channels
2
MVB Classification
Class 1
Galvanic isolation
Yes
Insulation strength
500 V AC / 1 minute *)
Physical layer
EMD, ESD
Communication rate
1.5 Mbps 0.01 %
Max. number of devices
32
Max. segment length without repeater
200 m for EMD / 20 m for ESD
Characteristic impedance
120 Ω 0.10 % **)
Connection point
2 × 2 D-sub DE-9 (concatenation)
connector fixing by M3 bolt
*) Isolation must not be used for dangerous voltage separation.
**) Terminators are included.
Voltage level
5 V
Output impedance
50 Ω
Connection point
BNC connector
Number of ports
1
Data communication rate
10/100 Mbps
Galvanic isolation
Yes
Galvanic isolation strength
500 V AC / 1 minute *)
Connection point
RJ45 connector according to IEEE802.3
Recommended cabling
STP CAT5
Maximum segment length
100 m
Nominal power supply voltage
24 V DC
Power supply voltage range
16.8 V to 33.6 V DC
Power consumption
Max. 0.6 A at 24 V DC
Starting peak current
Max. 15 A / < 1 ms at 24 V DC
Galvanic isolation
Yes
Insulation strength
500 V AC / 1 minute *)
Connection point
Connector WAGO 769-103/021-000
Wire cross section
0.5 mm2 to 4 mm2
*) Isolation must not be used for dangerous voltage separation.
Mechanical design
Metal case
Surface finish
Powder coating
Colour
RAL7035
Mounting
2 × ø 6 mm hole
Ingress protection rate
IP20
Weight –netto
–brutto
0.9 kg ±5 %
1.14 kg ±5 %
Dimensions (w × h × d)
(50 × 228 × 113) mm
Package dimensions (w × h × d)
(260 × 180 × 115) mm
MVB interface
Trigger output
Ethernet
Power supply
Mechanics

RB-MVB/AN02
9/30 rb-mvban02_g_en_100
Unit overall mass of plastics
144 g
Included mass of self-extinguishing
plastics
144 g
Module does not contain
PUR, PVC, Asbestos
Module complies
2011/65/EU (ROHS)
1907/2006EU (REACH)
Operating temperature
-40 °C to 70 °C
Storage temperature
-40 °C to 70 °C
Maximum ambient humidity
< 95 % non-condensing
Expected MTBF
> 150 000 h
Expected lifetime
15 years
None
Equipment is intended to operate up to 1 400 m above the sea level.
Equipment is designed to meet the Temperature Class TX.
According to EN 61373:2010 standard, the equipment is classified in terms of
vibrations into Category 1, Class A (mounting to vehicle body).
Permissible supplying voltage drop-outs duration: max 10 ms (Class S2 according to
Chapter 3.1.1.2 of EN 50155:2007).
For supply voltage switching are permissible conditions of C1 and C2 Class.
The device is not classified according to EN 50128:2011 Railway applications –
Communications, signalling and processing systems –Software for railway control
and protection systems.
The device is not classified according to EN 50129:2003 Railway applications –
Communication, signalling and processing systems –Safety related electronic
systems for signalling.
Device is supplied with loader, which enables software downloading using ADS
Manager application via serial service line.
Dangerous
materials
Temperatures
Others
Components
with reduced
lifetime
Claims EN
50155:2007
Safety
classification
Software

RB-MVB/AN02
rb-mvban02_g_en_100 10/30
4.1. Dimensions
xxxxxxx S/N:
WEIGHT: 0.87 kg
DATE: 09.06.2015
MAC: xx-xx-xx-xx-xx-xx
HiPot: HiPot - OK
TEST: OK-JE
LDR: 1.0
POWER: 24 V DC / 0.6 A
TYPE:
RB-MVB/AN02
50
187 203 228
6
78
113
Fig. 1 - RB-MVB/AN02 mechanical dimensions in mm