amphis SOLEADO User manual

SOLEADO
2400W FAR INFRARED (FIR) RADIANT HEATER
INSTALLATION MANUAL
108100, 108101

1
SOLEADO – INSTALLATION MANUAL
Thank you for purchasing this quality Amphis product.
Please read carefully before installation.
WARRANTY
This Amphis product is covered by a 3-year residential warranty. The warranty period starts
from date of purchase. Proof of purchase will be required.
Warranty will be void if the heater is not assembled and installed by a licensed electrician,
is used with a non-compatible dimmer, or if there is any damage due to improper usage or
modification to the luminaire.
RADIANT HEATER THEORY
Infrared radiant heaters produce heat through a unique design process and the application of
an alloy radiation panel embedded with a heating element. The heating element generates
and transfers heat to people and objects, instead of warming the air, similar to the way the
sun’s rays can be felt even on a cold day. Warming the surfaces of your room, instead of
the air, will not lead to air convection, meaning that the air is fresh and clean. It is easier to
maintain a relative indoor humidity and heat distribution, feels more natural and fresh, and you
feel more comfortable, as though being bathed in the warmth of the sun.
PERFORMANCE FEATURES
Comfort – No wind, light or odour will be caused during the running of this heater. Indoor air is
clean and without floating dust particles.
Energy-saving – The heater has a high heat generation efficiency and good heat radiation
effect, controlling the temperature intelligently, which saves power and energy.
Reliable – The indoor temperature can be adjusted freely, despite outside temperatures.
Health benefits – Radiant heat has been found to have health benefits as it interacts with
the body’s molecules. It can change body microcirculation, cell organisation under the skin
producing resonance, adjust and balance the nervous system and promote metabolism.

2
SOLEADO – INSTALLATION MANUAL
WORKING CONDITION
Ambient Temperature: -30˚C to 30˚C
Power Source: GPO Plug
Rated Voltage: 220-240V
Rated Frequency: 50Hz/60Hz
Relative Humidity: less than 95%
INSTALLATION CONDITIONS
1 Supply voltage fluctuation range should be within ±10%. If this range is not met, it must be
revised before installation.
2 If there is a serious security risk in the users’ electricity environment the installation should be
refused, until the elimination of the security risks is carried out.
3 Electrical lines must be equipped with earth leakage protection devices and master switch.
INSTALLATION CONDITIONS
MODEL NO. POWER (W) RATED
CURRENT (A) VOLTAGE (V) CABLE LENGTH (mm)
108100 2400 10 220-240 2000
108101 2400 10 220-240 2000

3
SOLEADO – INSTALLATION MANUAL
INSTALLATION INSTRUCTIONS
MODEL NO. DIMENSION A DIMENSION B DIMENSION C
108100 1875mm 1200mm –
108101 1500mm 1200mm 95mm
A
B(min)
LENGTH
SPAN OF EXPANSION SCREWS
AC
LENGTH
B(min)
SPAN OF EXPANSION SCREWS
108100
108101

4
SOLEADO – INSTALLATION MANUAL
INSTALLATION INSTRUCTIONS
ADJUSTING BRACKET
SLIDING BRACKET
SCREW, FLAT WASHER,
SPRING WASHER AND
NUT (SPEC M6)
SLIDING BRACKET
Step 1 Connect heater adjusting bracket and sliding bracket.
Step 2 Install sliding bracket on heater (as arrow directs).

5
SOLEADO – INSTALLATION MANUAL
EXPANSION SCREWS
ADJUSTING BRACKE
T
BUTTERFLY HAND SCREW
SCREW, FLAT WASHER,
SPRING WASHER AND
NUT (SPEC M5)
Step 3 Fix wall adjusting bracket into the wall with expansion screws.
Step 4 Connect the two (heater and wall) adjusting brackets; make sure to lock
brackets tightly using the butterfly hand screw.
INSTALLATION INSTRUCTIONS

6
SOLEADO – INSTALLATION MANUAL
15˚
60˚
15˚
60˚
135mm
85mm
WALL INSTALLATION
CEILING INSTALLATION 1
(ADJUSTABLE MOUNT)
CEILING INSTALLATION
CEILING INSTALLATION 2
(NON-ADJUSTABLE MOUNT)
INSTALLATION INSTRUCTIONS

7
SOLEADO – INSTALLATION MANUAL
OPERATING THE REMOTE
1. On/off Button
Press ON/OFF button to turn the heater on and off.
2. Clock Button
Remote is powered on (as shown in picture 2-1). Present time is 00:00.
Set the time as follows:
Press Clock button. The hours will flash (as show in picture 2-2).
Press up or down button to change hour setting.
Press Clock button. The minutes will flash (as shown in pictures 2-3).
Press up or down button to change minute setting.
Press Clock button. The seconds will flash (as shown in picture 2-4).
Press up or down button to change hour setting.
Press Clock button again. The seconds will stop flashing and the setting is finished.
POWER
PERCENTAG
E
POWER
TIME
TIME ON
TIME OFF
HEAT
LEVEL
STANDBY SENDING FAST HOT
REMOTE APPEARANCE REMOTE LED DISPLAY
2-1 2-2 2-3 2-4

8
SOLEADO – INSTALLATION MANUAL
OPERATING THE REMOTE
3. Level Button
Press Level button to adjust the power when the heater is on (as shown in picture 3-1).
4. Fast Hot Button
Press Fast Hot button to turn the Fast Hot function on and off. The Fast Hot function lets the
heater run at full power for a certain time, to achieve the purpose of rapid heating.
5. Timer On Button
If the heater is off, to set a timer to turn the heater on do the following:
1 Press Timer On button. Display will show “ ON” --:-- (as shown in picture 5-1).
2 Press up or down to change the hour (as shown in picture 5-2).
3 Press Timer On button. The hours will stop flashing and the minutes will flash.
4 Press up or down to change the minutes (as shown in picture 5-3).
5 Press Timer On button again to finish timer function. Display will show the present time
and “ ON”. (Example in picture 5-4 shows current time of 4:30pm and that timer is set
to turn on, with timer having been set to 8:30pm as in previous steps).
5-1 5-2 5-3 5-4
3-1
4-1 4-2

9
SOLEADO – INSTALLATION MANUAL
6. Timer Off button
If the heater is on, to set a timer to turn the heater off do the following:
1 Press Timer Off button. Display will show “ OFF” --:-- (as shown in picture 6-1).
2 Press up or down to change the hour (as shown in picture 6-2).
3 Press Timer Off button. The hours will stop flashing and the minutes will flash.
4 Press up or down to change the minutes (as shown in picture 6-3).
5 Press Timer Off button again to finish timer function. Display will show the present time
and “ OFF”. (Example in picture 6-4 shows current time of 4:30pm and that timer is set
to turn off, with timer having been set to 8:30pm as in previous steps).
LED INDICATORS
6-1 6-2 6-3 6-4
1234 5
HEATER LED INDICATOR APPEARANCE
LED indicators 1 – 4 show the heater’s power level or timer settings (as detailed below)
LED 5 is the far-infrared receiver.
All LED indicators off = heater is off
OPERATING THE REMOTE