AmpliVox W-450 User manual

Easy Step-By-Step Instructions for
W/S/SW-450 Presidentia P us Lectern Assemb y
Featuring Quickfit-Expando 6 Connectors
1-800-267-5486
The Presidential Plus Lectern is designed
for easy assembly. If you have any questions
about assembling or using your new sound
system, or if you want more information
about accessories, call AmpliVox’s customer
service line.
The lectern is carefully packed
to minimize shipping damage. If your unit
was damaged in shipping call our toll-free
customer service line or visit our web site at
http://www.ampli.com
NOTES ON ASSEMBLY
Use CAUTION during assembly
board edges can be sharp and
may chip if mishandled.
Remove staples from carton and
use carton to set parts on during
assembly.
ASSEMBLY INSTUCTIONS
1. Unpack all the pieces. Be sure
to save the packing and the box
in case you need to return the
lectern. Check that you have all
the pieces and that they are not
damaged. [figure 1]
2. Insert the steel pins. With your
thumb [use phillips screwdriver
to ease insertion], push the steel
pins into the holes in the two
sides. Make sure the plastic
collar is flush with the wood
surface. [figure 2]
Hardware :
14 Quickfit-Expando 6 Connectors
[pre-installed]
14 Push-in Quickfit 6 Expanding
dowels
4 Minibloc Connectors[pre-installed]
8 Minibloc crewpins
4 Plate Casters [2 Locking]
16 #10 x 3/4 PPH crews
Tools Needed :
Phillips crewdriver
POWER TOOLS ARE NOT
RECOMMENDED
Edge of board
Edge of board
3. Inspect the Quickfit-Expando 6
Connectors. The flat edge of the
connector must be facing the
outer edge of the board.
Use phillips screwdriver to rotate,
if needed.
UNLOCKED LOCKED
TURN COUNTERCLOCKWISE
TO UNLOCK
LOCKED UNLOCKED
#10 x 3/4 PPH S rew
[16 required]
Plate Caster
Lo king
[2 required]
Plate Caster
Nonlo king
[2 required]
Qui kfit-6
Expanding Dowel
[14 required]
Qui kfit-Expando 6
Conne tors
[14 required]
Pre-inserted
Qui kfit-Expando Miniblo
Conne tors
[4 required]
Packing List:
Reading Table
Bottom Panel
2 ide Panels, left and right
Front-Dual peaker Panel
Center helf
Black peaker Grille [ / W450]
Hand Held Microphone [ / W450]
Microphone Cable [ / W450]
Gooseneck [ / W450]
hock Mount Microphone Holder [ / W450]
Amplifier [ 450]
Wireless Amplifier [ W450]
figure 1
Minibloc Screwpins
[8 required]

figure 2
figure 3 figure 4
4. Attach front panel to left side. With the
left side panel laying on the work surface,
attach the front panel by sliding the connectors
over the steel pins. Both bottom unfinished edges
should be on the side. Use a phillips screwdriv-
er to tighten the 3 Quickfit-Expando 6 connec-
tors. Turn 1/2 turn clockwise.
Do not overtighten the connectors. Over
tightening can break the connectors. [figure 3]
5. Install ottom panel. Push Minibloc connec-
tors in the bottom panel. Place bottom panel in
the slot on the leftsidepanel,flat unfinished edge
against the front panel. Using a phillips screw-
driver, install 4Minibloc crewpins through the
Minibloc holes into the predrilled holes in the
side panel. [figure 4]
6. Attach right side panel. Place the right side
onto the front and bottom panel, tighten the 3
Quickfit-Expando 6 connectors in the
front panel and install 4 Minibloc
crewpins in the 2 Minibloc connectors on
the bottom panel. Carefully roll unit onto
front panel.
7. Install reading ta le and shelf. lide read-
ing
table over steel pins and tighten 4 Quickfit-
Expando 6 connectors. lide shelf over steel pins
and tighten 4 Quickfit-Expando 6 connectors.
Install 2 locking casters on the finished side of
the bottom panel and 2 non-locking casters using