AMX RDA-ENC2 User manual

Installation Guide
RDA-ENC2/ENC4/ENC6
Overview
The AMX Lighting™ RDA-ENC2 (FG606-10), RDA-ENC4 (FG606-11), and
RDA-ENC6 (FG606-12) enclosures provide secure mounting for all Radia
controllers/modules. The enclosures are CE, UL, and C-UL approved.
Installation Instructions
• For indoor use only.
• Mount on vertical surface only.
• Maintain 12" (304.88 mm) minimum clearance above and below the enclo-
sure.
• Route class 1 conductors through upper conduit knockouts.
• Route class 2 conductors through lower conduit knockouts.
• Use 75°C (167°F) copper conductors only.
• Install filler plate #28-10500 (RDA-EFP) in all unused openings.
• Install only UL approved modules (see the UL Number Cross Reference to
AMX Lighting ID table).
Enclosure Weights
• RDA-ENC2: 4.5 lb. (2.04 kg)
• RDA-ENC4: 7.5 lb. (3.40 kg)
• RDA-ENC6: 9.5 lb. (4.31 kg)
Radia enclosures must be mounted on a vertical surface with a minimum of 12"
(304.8 mm) clearance above and below the enclosure.
Dimensions between center lines (from FIG. 2):
RDA-ENC2:
• A to B = 5.25" (133.4 mm)
• B to C = 11.0" (279.4 mm)
RDA-ENC4:
• A to B = 10.0" (254.0 mm)
• B to C = 11.0" (279.4 mm)
RDA-ENC6:
• A to B = 16.0" (406.4 mm)
• B to C = 11.0" (279.4 mm)
FIG. 1 Top, front, bottom, and side views of the RDA enclosures
RDA-ENC2 RDA-ENC4
RDA-ENC6
Side View
(for all enclosures)
12.0"
(304.8 mm)
6.0" (152.4 mm)
0.75" (19.05 mm)
12.0"
(304.8 mm)
6.0"
(152.4 mm)
18.0"
(457.2 mm)
FIG. 2 Bracket configuration
A to B
B to C
Bottom slot
To p s l o t
Configuration for
right and left
mounting brackets
for all Radia
enclosures.
Maximum mounting
screw size: #12

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
11/08
©2008 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax [phone] • technical support 800.932.6993 • www.amx.com
93-0606-12 REV: A
UL Number Cross Reference to AMX Lighting ID
The following table provides a cross reference between the UL ID module
numbers and AMX Lighting module IDs. The modules identified are the only
modules that can be used in the RDA-ENC2, RDA-ENC4, and RDA-ENC6
enclosures.
UL Number Cross Reference to AMX Lighting ID
UL ID AMX ID
10-28400 RDM-DC, RDM-2DC, RDM-3DC
10-28410 RDM-FDB, RDM-2FDB, RDM-3FDB
28-10100 RDC-DC/120
28-10110 RDC-DC/240
28-10120 RDC-DC/277
28-10130 RDC-PDC/120
28-10133 RDC-PDC/240
28-10140 RDD-DM6/120
28-10150 RDD-DM6/240
28-10160 RDD-DM6/277
28-10170 RDA-PSM/120
28-10200 RDM-INC
28-10210 RDM-2INC
28-10220 RDM-INC50
28-10230 RDM-ZC, RDM-2ZC, RDM-PR, RDM-2PR
28-10240 RDM-ZC50
28-10260 RDM-SWM, RDM-2SWM, RDM-3SWM
28-10270 RDM-HSW, RDM-2HSW, RDM-3HSW
28-10280 RDM-MR, RDM-2MR, RDM-3MR
28-10290 RDM-MR35
28-10300 RDM-MR60
28-10310 RDM-MDM
28-10340 RDA-CHK
28-10350 RDM-HFDB
28-10360 RDM-DPSM
28-10370 RDM-HDC