AMX Modero NXA-WAP200G User manual

instruction manual
To u c h Pa n e l s a n d A c c e s s o r i e s
NXA-WAP200G
Modero Wireless Access Point and
External Antennas

AMX Limited Warranty and Disclaimer
AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three
(3) years from the date of purchase from AMX Corporation, with the following exceptions:
• Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch
overlay components that are warranted for a period of one (1) year.
• Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one
(1) year.
• AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting
products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the
control of dimmable loads that are properly connected to our lighting products. The dimming performance or
quality cannot be guaranteed due to the random combinations of dimmers, lamps and ballasts or transformers.
• Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year.
• AMX Software is warranted for a period of ninety (90) days.
• Batteries and incandescent lamps are not covered under the warranty.
This warranty extends only to products purchased directly from AMX Corporation or an Authorized AMX Dealer.
All products returned to AMX require a Return Material Authorization (RMA) number. The RMA number is
obtained from the AMX RMA Department. The RMA number must be clearly marked on the outside of each box.
The RMA is valid for a 30-day period. After the 30-day period the RMA will be cancelled. Any shipments received
not consistent with the RMA, or after the RMA is cancelled, will be refused. AMX is not responsible for products
returned without a valid RMA number.
AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform.
This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not
liable for any claim made by a third party or by an AMX Dealer for a third party.
This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort
claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of
liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX
Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such
damages. This limitation of liability, however, will not apply to claims for personal injury.
Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or
exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of
the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may
also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full
determination of rights.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO
OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX CORPORATION
EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY
IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS
LIMITED WARRANTY.

FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received; including interference that may cause undesired operation.
Federal Communications Commission (FCC)
Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed an operated with a minimum
distance of 20 centimeters between the radiator and your body.

Table of Contents
i
NXA-WAP200G Wireless Access Point
Table of Contents
Introduction ...............................................................................................................1
Specifications .................................................................................................................... 2
WAP200G Connector Locations ....................................................................................... 4
LEDs ........................................................................................................................................ 4
WAP200G Accessories ............................................................................................5
NXA-WAP2403A 3 dBi Ceiling Mount Omnidirectional Antenna....................................... 5
NXA-WAP2405A 5.5 dBi Rack/Ceiling Mount Antenna .................................................... 7
NXA-WAP2410A 10 dBi Directional Yagi Antenna ......................................................... 10
NXA-WAP2413A 13 dBi Indoor/Outdoor Directional Panel Antenna .............................. 13
Installation ...............................................................................................................17
WAP Location and Antenna Direction ............................................................................. 17
Mounting the WAP200G using the mounting holes ............................................................... 17
Connecting the Optional Accessory Antennas ................................................................ 18
Connecting the WAP to a LAN ........................................................................................ 18
Set the AP/BRIDGE Slide Switch.................................................................................... 18
Determining the Power Source (AC or PoE) ................................................................... 19
Configuring the Communication ...........................................................................21
Programming the Network Configuration ........................................................................ 21
Connecting to the WAP200G (cable connection)................................................................... 22
Connecting to the WAP200G (wirelessly) .............................................................................. 23
Wireless Device Communication Setup ...............................................................27
Logging into the WAP200G within Access Point Mode................................................... 27
WAP200G and Modero Unsecured Communication Setup ............................................ 28
Preparing the WAP for unsecured communication ................................................................ 28
Configuring the Modero panel for unsecured access............................................................. 30
Configuring the WAP200G for Secured Communication ................................................ 32
Configuring the Modero panel for secured access................................................................. 32
Preparing the WAP for secured communication .................................................................... 35
Configuring a secured connection on multiple wireless Moderos .......................................... 38
Configuring the WAP200G with a Static IP Address.............................................................. 39
Logging into the WAP200G within Bridge Mode ............................................................. 41
Configuring the WAP200G for Secured Bridge Mode Communication ........................... 42
Configuring the Modero panel for secured access (bridge mode) ......................................... 46
Upgrading the WAP200G On-Board Firmware ............................................................... 46

ii NXA-WAP200G Wireless Access Point
Table of Contents
AP/Repeater Configuration Utility Pages .............................................................49
Status Page..................................................................................................................... 49
Connected Devices Page................................................................................................ 50
Basic Wireless Configuration Page................................................................................. 51
Access Control Page....................................................................................................... 53
Repeater Configuration Page.......................................................................................... 55
Advanced Wireless Configuration Page.......................................................................... 57
Security and Encryption Settings Page........................................................................... 58
Configuration of a WEP security protocol .............................................................................. 59
WPA Configuration................................................................................................................. 59
802.1X Configuration ............................................................................................................. 59
IP Address Configuration Page....................................................................................... 60
Administration Page ........................................................................................................ 61
Help Page ....................................................................................................................... 62
Bridge Mode Configuration Utility Pages ............................................................63
Status Page (Bridge Mode)............................................................................................. 63
Basic Wireless Configuration Page (Bridge Mode) ......................................................... 65
Security and Encryption Settings Page (Bridge Mode) ................................................... 67
Advanced Wireless Configuration (Bridge Mode) ........................................................... 68
Administration Page (Bridge Mode) ................................................................................ 69
Help Page (Bridge Mode)................................................................................................ 71
Troubleshooting .............................................................................................................. 71
Appendix .................................................................................................................73
Glossary of Terms........................................................................................................... 73

Introduction
1
NXA-WAP200G Wireless Access Point
Introduction
AMX's new NXA-WAP200G 802.11g Wireless Access Point/Wireless Bridge (FG2255-01)
provides both high performance and increased security to support all of AMX's G4 Modero
wireless touch panels. The NXA-WAP200G provides convenient WLAN access for office/home
computers with connection speeds of up to 54Mbps.
The NXA-WAP200G integrates Power Over Ethernet (PoE), Repeater, and Bridge capabilities
which increase your deployment and coverage options while easing the installation process.
 PoE allows you to deploy access points within locations where it would normally be
difficult and time consuming to run electrical wiring. PoE is an IEEE 802.3af standard
for distributing power over either a CAT5 (capable of up to 10/100 Mbps transmission) or
CAT6 (capable of up to 1 Gbps transmission) Ethernet cable. Within this configuration,
power is integrated onto the Ethernet cable through the PoE injector switch. Power and
data are then sent across the Ethernet cable to the terminal device which then separates
the power and data.
The NXA-WAP200G can be deployed in one of three modes to increase its deployment to those
locations where it could prove difficult to wire CAT5 Ethernet cables:
 Access Point Mode - In this mode the WAP200G is connected to the LAN through a
CAT5 Ethernet cable and enables all of AMX's G4 Modero Wireless Touch Panels to
connect to the network wirelessly.
 AP/Repeater Mode - When trying to install the WAP200G in a location that has
electricity but does not have an Ethernet connection, such as a brick wall with an existing
electrical outlet; the WAP can be placed in the AP/Repeater mode. This configuration
allows it to provide coverage for that area and send network traffic through another AP
back to the wired network using the Wireless Distribution System (WDS).
 Bridge Mode - In this mode, the WAP200G allows devices with only wired 10/100
Ethernet ports (such as a Printer, PlayStation2, X-Box, PVR, etc.) to be connected to the
LAN wirelessly.
This 802.11g WAP is also fully compatible with IEEE 802.11b standards, so it can connect with
any existing 802.11b compliant devices.
In addition, the WAP200G functions in tandem with optional external antennas that meet a variety
of reception/transmission needs. Each antenna provides coverage which suits their particular
installation needs and site requirements. Refer to the WAP200G Accessories section on page 5 for
more information.

Introduction
2NXA-WAP200G Wireless Access Point
Specifications
The following table outlines the specifications for the NXA-80211G AMX Wireless Access Point.
Specifications
Dimensions (HWD): • Antenna fully lowered: 1.34" x 5.12" x 4.33" (34 mm x 130 mm x 110mm)
• Antenna fully raised: 3.94" x 5.12" x 4.33" (100 mm x 130 mm x 110mm)
Weight: • Stand-alone unit: 0.50 lbs (0.23 kg)
• Unit with power adapter: 0.85 lbs (0.39 kg)
Power: Linking State Current Draw:
• 650 mA @ 5 VDC
Full Load Current Draw (during transmission):
• 820 mA @ 5 VDC while transmitting at 54 Mbps
• 750 mA @ 5 VDC while transmitting at 11 Mbps
Full Load Current Draw (during reception):
• 750 mA @ 5 VDC while receiving at 54 Mbps
• 700 mA @ 5 VDC while receiving at 11 Mbps
Radio Specifications:
WLAN standards • IEEE802.11/11b Industry standards
• IEEE 802.11g draft standards
Media Access protocol • IEEE802.11
Frequency • 2.412 - 2.484 GHz (Industrial Scientific Medical Band)
Operating channels • 11b Mode:
- 11 Channels (USA, Canada)
- 13 Channels (Europe)
- 14 Channels (Japan)
- 4 Channels (France)
• 11g Mode:
- 11 Channels (USA, Canada)
- 13 Channels (Europe, Japan)
- 4 Channels (France)
Wireless Restrictions • In R&TTE countries, such as France, the 802.11g frequency band is
restricted to 2454 - 2483.5 MHz (2.454 - 2.4835 GHz) and a max power
output of 100 mW EIRP outdoors.
Data Rate • 1, 2, 5.5, 6, 9, 11, 12, 24, 36, 48, and 54 Mbps
Modulation technique • CCK for 11b mode (1, 2, 5.5, and 11 Mbps)
• OFDM for 11g mode (6, 9, 12, 24, 36, 48, and 54 Mbps)
Security • 64-bit & 128-bit WEP Encryption
Output power • 15 dBm @ 11M CCK
• 10 dBm @ 54M OFDM
Coverage area • Indoor: 100 ft (30.48 m)
• Outdoor: 100 ft (30.48 m)
Firmware/Software
Specifications:
Management • Built-in browser-based management with User Name/Password
authentication
Firmware upgrade • TFTP
IP configuration • Static IP or DHCP client
Protocols • Transparent to layer 3 protocols, such as PPoE and VPN

Introduction
3
NXA-WAP200G Wireless Access Point
Specifications (Cont.)
Front Components:
LEDs • Three blue activity and status LED indicators
• Refer to the following LEDs section on page 4 for more information.
Rear Components:
Power connector Two power options available:
•AC Adapter connects to an external power adapter.
•Power Over Ethernet (PoE) powers the device through the CAT5 cable.
Both Power and Data can be transmitted simultaneous through the CAT5
cable when using the appropriate equipment.
Reset button • Pressing this button for 10 seconds, restores the default settings.
Note: Resetting the WAP will erase all of your settings (WEP Encryption,
Wireless and LAN settings, Passwords, etc.) and restore them to their factory
default values. Do not reset the WAP if you want to retain these settings.
LAN port • One 10/100M (RJ-45) connector.
• This 10/100 Ethernet Port (RJ-45 Connector) is used to connect the WAP to
your LAN and/or to connect your Internet device to the LAN when the
NXA-WAP200G is used as a Bridge.
LAN/PC switch The NXA-WAP200G can operate as a Wireless Access Point or as a Bridge.
• Single AP - BRIDGE toggle switch
• When configured as a Wireless Access Point it allows multiple computers to
connect to the LAN wirelessly.
• When configured as a Bridge it allows devices with a 10/100 port, but without
wireless capability, to be connected to the wireless LAN, such devices
include desktop computers, printers, X-Boxes, PlayStation2s, PVRs,
Stereos, etc.
• When the NXA-WAP200G is used a Wireless Access Point the toggle switch
should be positioned to AP.
• When it is used as a Bridge it should be positioned to BRIDGE.
Antenna connector • Single 3 dBi external antenna with reversed SMA connector.
• This is the connection point for any of the four optional external antennas.
Refer to the WAP200G Accessories section on page 5 for more information.
Certifications: • FCC, IC, CE, TELEC
Security Features: • MAC Address filtering
• Disabling of Wireless Beacon
• Hiding of SSID information
• 64 and 128-bit WEP Encryption
Operating/Storage
Environments:
• Operating Temperature: 0°C (32°F) to 50°C (122°F)
• Storage Temperature: -25°C (-13°F) to 70°C (158°F)
• Relative Humidity: 10% to 90% non-condensing
Included Accessories: • One power adapter
• Four international plug adapters (US/Japan, Europe, UK, and Australia)
• Surface mounting kit (including two screws)

Introduction
4NXA-WAP200G Wireless Access Point
WAP200G Connector Locations
FIG. 1 shows the back panel of the NXA-WAP200G wireless access point:
LEDs
The LEDs are indicators of switch activity and performance. The following table shows the status
of the LEDs. You can check each connection by viewing the port status indicators shown in the
following table.
Specifications (Cont.)
Optional Accessories: • NXA-WAP2403A, 3 dBi Ceiling Mount Omnidirectional Antenna (FG2255-20)
• NXA-WAP2405A, 5.5 dBi Rack/Ceiling Mount Antenna (FG2255-21)
• NXA-WAP2410A, 10 dBi Directional Yagi Antenna (FG2255-23)
• NXA-WAP2413A, 13 dBi Indoor/Outdoor Directional Panel Antenna
(FG2255-22)
FIG. 1 NXA-WAP200G (rear view)
Device LED Descriptions
LED Status Description
PWR (power) Blue: On Power is supplied to the device
Blue: Off Power is disconnected from the device
WLAN - Link/Activity Blue: On Wireless LAN is active
Blue: Blinking Wireless data is being transmitted
LAN - Link/Activity Blue: On Connected to LAN/Internet Device
Blue: Blinking Indicates data activity
Power port
RESET button
Ethernet connector
AP/BRIDGE switch
Antenna connector

WAP200G Accessories
5
NXA-WAP200G Wireless Access Point
WAP200G Accessories
The following section outlines and describes the optional WAP200G accessory antennas:
 NXA-WAP2403A, 3 dBi Ceiling Mount Omnidirectional Antenna (FG2255-20)
 NXA-WAP2405A, 5.5 dBi Rack/Ceiling Mount Antenna (FG2255-21)
 NXA-WAP2410A, 10 dBi Directional Yagi Antenna (FG2255-23)
 NXA-WAP2413A, 13 dBi Indoor/Outdoor Directional Panel Antenna (FG2255-22)
Each antenna is designed to meet the needs required by a particular installation location.
NXA-WAP2403A 3 dBi Ceiling Mount Omnidirectional
Antenna
This 2.4 GHz Omni-directional antenna (FIG. 2) is designed for applications that require a
frequency coverage from 2.4 GHz to 2.5 GHz.
FIG. 2 NXA-WAP2403A Omnidirectional Ceiling Mount Antenna
Specifications for NXA-WAP2403A
Dimensions (HWD): • 5.00" x 10.0" x 0.12" (127.0 mm x 254.0 mm x 3.05 mm)
Description: • 3 dBi Ceiling Mount Omni-directional Antenna (@ 2.4 GHz).
Features: • 3 dBi antenna provides true omni-directional performance.
• 3 foot (0.915 m) UL910 Plenum cable can be installed in the strictest indoor
mounting locations (including air ducts).
• Dual 10-32 stud mount.\
• Utilizes UL94-V0 materials which provide the UL’s highest flame retardant
rating. This use of materials provides maximum placement flexibility while
meeting the most stringent building codes.
Weight: • 0.5 lbs (0.23 kg)
Max Power Input: • 20 Watts
Frequency Range: • 2400-2500 MHz
Nominal Gain: •3dBi
Isolation: • > 25 dB

WAP200G Accessories
6NXA-WAP200G Wireless Access Point
FIG. 3 represents the NXA-WAP2403A Elevation cut.
Specifications for NXA-WAP2403A (Cont.)
Horizontal Bandwidth: • 360°
Vertical Bandwidth: • 55°
VSWR: • < 2.0 : 1
Mounting Method: • Dual 10-32 stud mount.
Nominal Impedance: • 50 Ohms
Polarization: • Vertical, linear
Cable: • 3 foot (0.915 m) Plenum RG58/U
Connector Type: • Reverse polarity SMA
Operating Temperature: • -40°C to +70°C
Certifications: • FCC (United States)
• CE (Europe)
Included Accessories: • 3 dBi Omni-directional antenna.
• 3 foot (0.915 m) UL910 Plenum cable.
Optional Accessories: • NXA-WAP10C - 10' RG-58 Plenum Antenna Extension Cable (FG2255-26)
FIG. 3 NXA-WAP2403A Elevation cut

WAP200G Accessories
7
NXA-WAP200G Wireless Access Point
FIG. 4 represents the NXA-WAP2403A Azimuth cut.
NXA-WAP2405A 5.5 dBi Rack/Ceiling Mount Antenna
This antenna is designed to cover frequencies from 2400 to 2485 MHz with a VSWR of less than
1.5:1. The NXA-WAP2405A antenna (FIG. 5) design focuses energy where it is needed while
reducing extraneous transmissions.
FIG. 4 NXA-WAP2403A Azimuth cut
FIG. 5 NXA-WAP2405A Omnidirectional Rack/Ceiling Mount Antenna

WAP200G Accessories
8NXA-WAP200G Wireless Access Point
Specifications for NXA-WAP2405A
Dimensions (L & OD): • 9.8" L x 1.0" OD (248.9 mm x 25.4 mm)
Description: • 5.5 dBi Rack/Ceiling Mount Omnidirectional Antenna (@ 2.4 GHz).
Features: • 5.5 dBi Omnidirectional Antenna.
• An included 1/4-20 insert allows for easy installation onto ceiling tile rails.
• Optimized radiation pattern focuses energy where it is needed, while at the
same time, suppressing both upper and lower sidelobe energy.
• UL Plenum rated RG58 coax cable and UL94-V0 radome meet the strictest
safety specifications.
Weight: • 0.5 lbs (0.23 kg)
Wind Survival: • 125 mph (201.17 kph)
Max Power: • 5 Watts
Frequency Range: • 2400-2485 MHz
Nominal Gain: • 5.5 dBi
Horizontal Bandwidth: • 360°
Vertical Bandwidth: • 32°
VSWR: • < 1.5 : 1
Mounting Method: • 1/4-20 insert for clipping to a ceiling tile rail.
Nominal Impedance: • 50 Ohm
Polarization: • Vertical, linear
Cable: • 12" (30.5 cm) RG58
Connector Type: • Reverse polarity SMA
Operating Temperature: • -30°C to 75°C
Certifications: • FCC (United States)
• CE (Europe)
Included Accessories: • A 1/4-20 insert allows for easy installation onto ceiling tile rails.
Optional Accessories: • NXA-WAP10C - 10' RG-58 Plenum Antenna Extension Cable (FG2255-26)

WAP200G Accessories
9
NXA-WAP200G Wireless Access Point
FIG. 6 represents the NXA-WAP2405A Elevation cut.
FIG. 7 represents the NXA-WAP2403A Azimuth cut.
FIG. 6 NXA-WAP2405A Elevation cut
FIG. 7 NXA-WAP2405A Azimuth cut

WAP200G Accessories
10 NXA-WAP200G Wireless Access Point
NXA-WAP2410A 10 dBi Directional Yagi Antenna
This antenna can be used as bridge between two networks and/or point-to-point communications.
This design also provides improved front-to-back ratio and sidelobe suppression (reducing
interference). It features a robust mounting structure for consistent performance, regardless of
weather conditions. The NXA-WAP2410A antenna (FIG. 8) is field adjustable for vertical or
horizontal polarization with matched principal plane beamwidths (providing optimum performance
in either orientation).
FIG. 8 NXA-WAP2410A Outdoor Enclosed Yagi Antenna
Specifications for NXA-WAP2410A
Dimensions (L & OD): • 4.5" L x 3.0" OD (114 mm x 76 mm)
Description: • 10 dBi Directional Yagi Antenna (@ 2.4 GHz).
Features: • 10 dBi directional antenna.
• A 30 dB front-to-back ratio permits less physical separation on the tower, thus
adding mounting flexibility at installation sites where space is limited.
• Attractive weather-proof radome is constructed of UV resistant material. This
construction provides robust and trouble-free use in harsh outdoor
environments.
• Field adjustability allows for both vertical or horizontal polarity. This feature
eliminates co-channel interference from neighboring radiators.
• Includes a robust mast mount bracket which is designed to withstand up to
125 mph winds.
• Matched principal plane beamwidths provide excellent sidelobe suppression
and cross-polarization rejection of more than 20 dB.
• Provides superior signal quality (with enhanced gain performance) and
minimal interference from neighboring radiators.
• Polarity markings are molded onto the antenna and ensure installation in the
correct orientation.
• Small and unobtrusive 4.5" x 3" design enables a user to bridge any two
buildings without compromising the architecture.
Weight: • 1.0 lbs (0.5 kg)
Equivalent Flat Plate Area: • 0.060 ft2
Wind Survival: • 125 mph (201.17 kph)
Lateral Thrust at
Rated Wind:
• 5.8 lbs (2.63 kg)
Max Power: • 5 Watts
Front view Rear view

WAP200G Accessories
11
NXA-WAP200G Wireless Access Point
Specifications for NXA-WAP2410A (Cont.)
Frequency Range: • 2400-2485 MHz
Front to Back Ratio • 23 dB
Nominal Gain: • 10 dBi
Horizontal Beamwidth: • 55° (@ 1/2 power)
Vertical Beamwidth: • 55° (@ 1/2 power)
VSWR: • < 1.5 : 1
Mounting Method: • Heavy duty Yagi mounting bracket.
• MYK18 adjustable wall/pipe mount.
• Stacking harnesses.
Nominal Impedance: • 50 Ohms
Polarization: • Vertical or horizontal, linear (user adjustable)
Cable: • 3 foot (914.4 mm)
Connector Type: • Reverse polarity SMA
Operating Temperature: • -30°C to 75°C
Certifications: • FCC (United States)
• CE (Europe)
Included Accessories: • Heavy duty Yagi mounting bracket permits mast mounting on masts up to
2" O.D.
Optional Accessories: • NXA-WAP10C - 10' RG-58 Plenum Antenna Extension Cable (FG2255-26)

WAP200G Accessories
12 NXA-WAP200G Wireless Access Point
FIG. 9 represents the NXA-WAP2410A Elevation cut.
FIG. 10 represents the NXA-WAP2410A Azimuth cut.
FIG. 9 NXA-WAP2410A Elevation cut
FIG. 10 NXA-WAP2410A Azimuth cut

WAP200G Accessories
13
NXA-WAP200G Wireless Access Point
NXA-WAP2413A 13 dBi Indoor/Outdoor Directional Panel
Antenna
This antenna is designed to cover 2.4 GHz frequencies with a VSWR of less than 1.5:1. This allows
it to obtain a maximum gain, while still maintaining an attractive, low-profile package. The NXA-
WAP2413A antenna (FIG. 8) provides both efficient and stable performance, while providing both
indoor or outdoor mounting options.
FIG. 11 NXA-WAP2413A Indoor/Outdoor Directional Panel Antenna
Specifications for NXA-WAP2413A
Dimensions (HWD): • 8.8" x 8.1" x 1.6” (224.0 mm x 206.0 mm x 40.60 mm)
Description: • 13 dBi Indoor/Outdoor Directional Antenna (@ 2.4 GHz).
Features: • 13 dBi directional antenna.
• Attractive, low profile housing. Permits the unit to be mounted in either
vertical or horizontal polarity.
• Blends well with indoor and outdoor environments where aesthetic
considerations are important.
• Corner exit RG58 pigtail design permits the panel to be mounted in vertical or
horizontal polarity with a wide variety of connector options.
• Utilizes UL94-V0 materials and PC board that provide the UL’s highest flame
retardant rating for maximum placement flexibility. Meets most stringent
building codes.
Weight: • 1.2 lbs (0.54 kg)
Radome Material: • UL94-V0 plastic
Max Power Input: • 20 Watts
Frequency Range: • 2300-2500 MHz
Front to Back Ratio • > 18 dB
Nominal Gain: • 13 dBi
Horizontal Beamwidth: • 35° @ 3 dB
Vertical Beamwidth: • 35° @ 3 dB
VSWR: • < 1.5 : 1
Mounting Method: • Adjustable azimuth/elevation MPAB11 mount.
Nominal Impedance: • 50 Ohms
Lightning Protection: • DC grounded
Polarization: • Vertical or horizontal, linear
Top view Bottom view

WAP200G Accessories
14 NXA-WAP200G Wireless Access Point
FIG. 12 represents the NXA-WAP2413A Elevation cut.
Specifications for NXA-WAP2413A (Cont.)
Cable: • 12" (30.5 cm) RG58/U
Connector Type: • Reverse polarity SMA
Operating Temperature: • -40°C to +80°C
Certifications: • FCC (United States)
• CE (Europe)
Included Accessories: • Adjustable mounting brackets for indoor installation.
Optional Accessories: • Indoor corner mounting bracket and heavy duty outdoor mounting brackets
are also available.These provide maximum flexibility for both indoor or
outdoor installations.
• NXA-WAP10C - 10' RG-58 Plenum Antenna Extension Cable (FG2255-26)
• NXA-WAP2413AMB - Mounting Bracket for the NXA-WAP2413A
(FG2255-24)
• NXA-WAP2413ACMB - Corner Mounting Bracket for the NXA-WAP2413A
(FG2255-25)
FIG. 12 NXA-WAP2413A Elevation cut